Technical data

ManualsBrandsMaster ManualsDehumidifiersDH 41 H

Manual – MOVI-PLC® advanced DH.41B Controller

MOVI-PLC® advanced DHE41B control card

Technical Data and Dimension Drawings

8.2 MOVI-PLC

advanced DHE41B control card

MOVI-PLC

advanced DHE41B.. control card

Part number •MOVI-PLC

advanced DHE41B control card: 1821 160 7

Electrical supply The following data applies to all units (MDX, MX, compact controller):

• You must supply the binary inputs and outputs separately with DC 24 V (X31:1/2).

Integrated in MOVIDRIVE

MDX61B:

• Power consumption: P

max

= 6.8 W

• Voltage is supplied to the MOVI-PLC

advanced DHE41B control card through MOVIDRIVE

MDX61B via the backplane connector.

• When the power supply is disconnected, the function of the control card is maintained through the

DC 24 V back up supply (external DC 24 V supply must be provided at X10:9/10 on MOVID-

RIVE

MDX61B.

Integrated in MOVIAXIS

master module (MXM):

• Power consumption: P

max

= 8.5 W

• U = DC 24 V (–15 % / +20 %)

•I

max

= 600 mA

• Voltage can be supplied to the MOVI-PLC

advanced DHE41B control card either by the MOVIAXIS

switched-mode power supply module (MXS) or by an external voltage source. To do so, connect X5

between the individual units.

• If the MOVI-PLC

advanced DHE41B control card is supplied with DC 24 V via the MOVIAXIS

switched-mode power supply module, the functionality of the MOVI-PLC

advanced DHE41B..

control card is maintained when the power supply is disconnected (external DC 24 V supply at X16 of

the MOVIAXIS

switched-mode power supply module is required).

Potential levels MOVI-PLC

advanced DHE41B has the following potential levels:

• Potential control / CAN 1 / COM1

• Potential COM2

• Potential binary inputs and outputs

• Potential system bus CAN 2

Memory • Program memory: 8 MByte (for user program, incl. IEC libraries)

• Data memory: 4 MByte (for IEC application)

• Retain data: 32 kByte

• System variables (retain): 8 kByte

Binary inputs

X31:3...X31:10

Internal resistance

Signal level

Isolated (optocoupler), PLC-compatible (IEC 61131-2), cycle time 1 ms, unfiltered and filtered (filter

constant ca. 2 ms)

Can be configured as binary inputs or outputs

X31:6...X31:10 are interrupt-capable (response time <100 μs)

≈ 3kΩ, I

≈ 10 mA

DC (+13 V...+30 V) = "1" = Contact closed (in accordance with IEC 61131)

DC (–3 V...+5 V) = "0" = Contact open (in accordance with IEC 61131)

Binary outputs

X31:3...X31:10

Signal level

PLC-compatible (IEC 61131-2), response time 1ms

Can be configured as binary inputs or outputs

Maximum permitted output current I

A_max

= DC 150 mA per binary output

All 8 binary outputs can be subject to the maximum permitted output current I

A_max

at the same time.

"0" = 0 V "1" = DC+24 V

System bus CAN 2

X32:1 ... X32:3

• System bus CAN 1 and CAN 2 to CAN specification 2.0, part A and B, transmission technology to

ISO 11898

• The CAN 2 system bus is electrically isolated

• Max. 64 stations per CAN system bus

• Max. 64 SCOM transmit objects / 32 receive objects per CAN system bus

• Address range 0...127

• Baud rate: 125 kBaud...1 MBaud

• If X32 or X33 is the bus terminator, you must connect a terminating resistor (120 Ω) externally.

• You can remove connector X32 or X33 without interrupting the system bus

• The system bus can be run in layer 2 (SCOM cyclic, acyclic) or in accordance with the SEW-

MOVILINK

protocol.

System bus CAN 1

X33:1 ... X33:3

Ethernet 1 System bus, reserved

Ethernet 2 • TCP/IP

• Connection options: engineering PC, other control, intranet

USB USB 1.0 to connect an engineering PC (in preparation)

kVA