Technical data
Light Bulb Replacement (Figure 9)
WARNING!
• Turn the power off and remove the plug from
the outlet before replacing light bulb.
• To reduce the risk of fire, use 10 watt,
12 volt light bulb only.
1.Remove screws from top of light bulb cover.
2.Remove light bulb cover.
3.Gently push in on bulb and rotate
counterclockwise to release.
4.Insert new bulb into socket, push gently and
rotate clockwise to secure.
5.Replace light bulb cover and screws.
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all
instructions listed below may result in electric shock and/or serious personal injury.
NOTE: This stationary tool has been manufactured in accordance with the applicable
standard and equipment safety legislation. When using electrical appliances, it is important
to take safety precautions to avoid possible injury and damage. For that reason, you should
carefully read and store these instructions so that this information is available at all times.
SAVE THESE INSTRUCTIONS.
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and
adjusting wrenches are removed from tool before turning it on.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4. DON'T USE IN DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations, or
expose them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.
7. DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don't force tool or attachment to do a job for which it was not designed.
9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. Table 1, Minimum Gage for Power Cord shows the correct size to use depending
on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear
protective hair covering to contain long hair.
11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.
12.SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your
hand and it frees both hands to operate tool.
13. DON'T OVERREACH. Keep proper footing and balance at all times.
14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
15.DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters,
and the like.
16.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before
plugging in.
17.USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended accessories.
The use of improper accessories may cause risk of injury to persons.
18.NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
19.CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function - check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
1
10
GENERAL SAFETY RULES
WARNING: RISK OF PERSONAL INJURY. Use only accessories that are recommended by
the manufacturer for your model. Accessories that may be suitable for one tool may become
hazardous when used on another tool.
Recommended Accessories:
Model: 60701240 6" diameter grinding, polishing or buffing wheels
Model: 60701250 8" diameter grinding, polishing or buffing wheels
ACCESSORIES
FIGURE 9
Light Cover
Screws
Light Bulb
Bulb Socket
Light Bulb