80 Lake Ave North Paynesville, MN 56362 Phone: (320) 340-6464 www.master-mfg.
Note: Do not return product to the distributor/dealer for warranty work. Call Master Manufacturing at (320) 340-6464 for any warranty work or replacement parts. INTRODUCTION The purpose of this manual is to assist you in the assembly, operation and maintenance of your Master Gardner sprayer. Please read through this manual completely too fully understand how to operate and maintain your equipment.
ASSEMBLY The Master Gardner is assembled at the factory, with the exception of a few components to protect them from damage during shipping. Follow the steps below to complete assembly: Handle Assembly Align the Handle and Wire Clamp with the Lower Frame. Slide the Wire Clamp over the Lower Frame, and the Handle into the Lower Frame. Adjust the Handle to a comfortable height for the operator, and find the hole nearest this position that aligns with the hole in the Lower Frame.
Secure the Wire Clamps on the Handle and Lower Frame using the Phillips Screwdriver. Wiring Assembly Locate the Switch on the Upper Handle and make sure it is in the OFF position as shown. Locate the Wiring Harness Connector at the base of the Handle. Locate the Connector under the Back Panel, and connect it to the Wiring Harness Connector, making sure it is fully seated. Verify Pump and Switch operation by turning the Switch to the ON position.
Spray Gun Clips Locate the Spray Gun Clips in the bag marked GC-100Kit. These clips are used to hold the Spray Gun to the Cart. The Clips can be mounted on the tank or on the Upper Handle. When mounting to the Upper Handle, Insert the 10-24 x 1” screws through the Clips and then the hole located in the Flat Bar of the Hose Wrap on the Handle Upright (as shown). Fasten using the 10-24 Nyloc nuts and tighten.
Using the Master Gardner as a Trailer If the Master Gardner will be used with a garden tractor a trailer tongue can be attached to the sprayer for towing. Attach the trailer tongue (Item 8, figure B) to the sprayer frame (Item 7, figure B) aligning the holes and using the pin and hair pin (Item 3, figure B). Setup Charging the Battery 1.) Obtain the battery charger (Item 27, figure B).
Determine MPH Determining the proper walking speed can be done by marking off a length of 100 feet. The speed chartindicates the number of seconds it takes to travel 100 feet. Speed MPH 1 2 3 4 Time required to travel 100 ft 68 Sec. 34 Sec. 23 Sec. 17 Sec. Caution Do not spray on windy days. Protective clothing must be worn in some cases. Be sure to read the chemical label carefully.After all calibrations have been completed, add water and chemical to the tank.
o To spray with the wand, ensure the wand nozzle is pointed in the direction meant to be sprayed and pull the lever handle. To stop spraying with the wand release the lever handle on the spray wand and the pump will deactivate after reaching pressure. o To spray with the nozzle located on the front of the tank, ensure the power switch is in the off position and the spray wand is firmly attached to the tank or frame handle. Turn the valve located on the back panel to the ON position.
TROUBLE SHOOTING Pump will not turn on: 1. Ensure the battery is at full charge. Follow the directions for charging the battery in the Setup directions of this manual. 2. Ensure the power switch is in the on position (the I position is ON and the O position is OFF). Switch will be lighted in the on position only. 3. Check and Ensure all electrical connections are tight. Inspect the 3 pin connector at the lower base of the handle and ensure the two halves are pushed together completely.
WARRANTY PARTS SERVICE . Products sold shall be warranted from defects in workmanship and material when used within the service and scope for which they were designed for a period of one year from date of purchase. Warranty covers replacement parts ONLY. Contact Master Manufacturing for warranty parts at (320) 340-6464. Do not return product to your distributor/dealer. Please have your original sales receipt or other proof of purchase date when requesting any warranty parts.
Master Gardner Frame Figure A Parts List Master Gardner Frame Figure A Item # 1 2 3 4 5 6 7 8 9 11 Part Number 33-100158 33-100157 33-100156 TWA12 x1.75 -1/2 33-100155 33-100154 33-100158 33-100158 33-100160 Qty 1 1 1 2 2 1 1 1 4 Description Frame, Handle (Only available as entire frame) Handle adjustment knobs (pair with bolts) Hitch Pin Wheel, Composite, 12’ Dia x 1.
Master Gardner Tank Assembly Figure B 12
