Owner`s manual

32
Activate the opener with any of the following:
• The Remote Control Transmitter. Hold push button
down until the door starts to move.
• The Door Control. Hold push bar down until the door
starts to move.
• The Outside Keylock or Keyless Entry. (See
Accessories)
When the opener is activated with the safety reversing
sensor installed and correctly aligned:
1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for entry
and exit of pets and for fresh air).
4. If the door has been stopped in a partially open position,
it will close.
5. If obstructed while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
7. The garage door will reverse in the closing cycle, and the
opener lights will blink for 5 seconds, when the invisible
beam is broken. If fully open, the door will not close
when the beam is broken. The sensor has no effect in the
opening cycle.
If the sensor is not installed, or is not aligned correctly, the
door won't close from any remote transmitter. However, you
can close the door with the Door Control, the Outside
Keylock, or Keyless Entry, if you activate them until down
travel is complete. If you release them too soon, the door
will reverse.
Opener Lights will turn on under the following conditions:
When the opener is initially plugged in; when the power is
interrupted; when the opener is activated. They will turn off
automatically after 4-1/2 minutes or provide constant light
when the Light feature on the Multi-Function Door Control is
activated. Bulb size is 100 watts maximum.
Lights will also turn on when someone walks through the
open garage door. With a Multi-function Door Control, this
feature may be turned off as follows: With the opener lights
off, press and hold the light button for 10 seconds, until the
light goes on and off again. To restore this feature, start with
the opener lights on, then press and hold the light button for
10 seconds.
NOTICE
Manual
Release
Handle
(Pull at 45° angle)
Trolley
Trolley
Release Arm
Lockout position
(Manual disconnect)
To reconnect
Weak or broken springs could allow an open door to fall
(either rapidly or unexpectedly), resulting in serious
injury, death or property damage. If possible, use the
manual release rope and handle only when the door is
fully closed.
Operation of Your Opener
WARNING
To open the door
manually:
The door should be fully
closed if possible. Pull
down on the manual release
handle (so that the trolley
release arm snaps into a
vertical position) and lift
the door manually. The
lockout feature prevents
the trolley from recon-
necting automatically, and
the door can be raised and
lowered manually as often
as necessary.
To reengage the trolley:
Pull the manual release
handle toward the opener at
a 45° degree angle so that
the trolley release arm is
horizontal. The trolley will
reconnect on the next UP or
DOWN operation, either
manually or by pressing the
Door Control push bar.
Trolley
NOTICE
Trolley
ReleaseArm
(in Manual
Disconnect
Position)
Door Control Push Bar: Press the white square to open
or close the door. Press again to
reverse the door during
the closing cycle or to
stop the door while it's opening.
Light Feature: Press the Light button. If the opener light is
off, it will turn on . If the opener light is on, (even in the 4-1/2
minute automatic cycle) it will turn
off.
But if you use the Light button to turn the lights on and then
activate the opener, the lights will turn
off after 4-1/2
minutes.
The 4-1/2 minutes interval can be changed to 1-1/2, 2-1/2, or
3-1/2 minutes as follows: Press and hold the Lock button
until the light blinks (about 10 seconds). A single blink
indicates that the timer is reset to 1-1/2 minutes. Repeat the
procedure and the light will blink twice, resetting the timer to
2-1/2 minutes. Repeat again for a 3-1/2 minute interval, etc.,
up to a maximum of four blinks and 4-1/2 minutes.
The Light button will not control the opener lights when the
door is in motion.
Lock Feature: The Lock feature is designed to prevent
operation of the door from remote controls. However, the
door will
open and close from the Door Control push bar,
the Outside Keylock and the Keyless Entry Accessories.
To Activate: Press and hold the Lock button for
2 seconds. The push bar light will flash as long as the
Lock feature is
on.
To turn off: Press and hold the Lock button again for
2 seconds. The push bar light will stop flashing. Normal
operation will resume. The Lock feature will also turn off
whenever the “Smart” button on the opener panel is
activated.
Operation of the Multi-Function Door Control
(See additional programming features, next page.)