INSTRUCTIONS FOR ASSEMBLY, OPERATION, SERVICING & STORAGE DELUXE 50 GALLON UTV SPRAYERS 12VUTV-M 320.340.
320.340.6464 TABLE OF CONTENTS TOOLS REQUIRED & INCLUDED HARDWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 UTV SPRAYER COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 UTV SPRAYER ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 IMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 GENERAL CHEMICAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . .
20.340.6464 1/2” SOCKET WRENCH PLIERS LON TAP EF E T TOOLS REQUIRED TEFLON TAPE INCLUDED HARDWARE NOTE: SOME PARTS MAY BE SHIPPED INSIDE THE TANK! CLOSELY INSPECT ALL CONTENTS IN THE SHIPPING CARTON • If you have damaged components: Contact the freight company that delivered the unit and file a claim. • If you have missing components: Contact us at 320-340-6464.
SPRAYER COMPONENTS SPRAYER COMPONENTS SPRAYER COMPONENTS 320.340.6464 Drain Cap Tether (1) 33-103219 Drain Cap Gasket (1) 33-103220 Drain Cap (1) 33-103218 Wand Bracket (1) 31-100411 3/4” Bolts (2) 33-200120 Boom Mount Bracket (2) 31-100420 Wing Nut (2) 33-103068 3.
320.340.6464 UTV SPRAYER ASSEMBLY 2. TOOLS PARTS TOOLS 1. None None PARTS Creates Drain Cap Assembly Applies Drain Cap to Drain Port Press the Drain Cap Gasket into the Drain Cap until fully seated. Locate Sprayer Tank drain outlet. Attach the Drain Tether to the top of the Drain Cap. Place other end of Tether over tank drain outlet. Thread Drain Cap over drain until hand tight. 4. PARTS PARTS TOOLS 3. TOOLS 5 None Installs Tank Lid Thread Tank Lid onto Sprayer Tank.
320.340.6464 6. PARTS LON TAP EF E T TOOLS PARTS TOOLS 5. Attaches Gun Assembly to Sprayer Wrap Teflon Tap around threads of Pressure Gauge. Place Hose Clamp over the Spray Gun Hose, then push the hose onto the bottom hose barb of the Pressure Regulator Assembly. Twist Pressure Gauge into top port of the Pressure Regulator Assembly. Don’t Over-tighten. Tighten the 1/2” Hose Clamp with a pliers and place the Spray Gun in the Spray Gun Bracket. 8. TOOLS PARTS TOOLS 7.
320.340.6464 10. PARTS TOOLS PARTS TOOLS 9. None Attaches Boom Mounting Brackets Attaches Boom Inlet Hose to Pump Scew the Boom Inlet Hose onto the Boom Shut-Off Valve. Place the Boom Mounting Bracket in front of the Boom Mounting Arm with the angled side facing the inside top as shown above. Insert the Square U-Bolt from behind the Boom Mounting Arm and attach with included nuts. Tighten with a Socket Wrench.
320.340.6464 OPERATION - IMPORTANT SAFETY INFORMATION Now that you have assembled your sprayer, there is some important safety and health information you need to know with regard to handling and spraying chemicals. TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS SECTION IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PROPERTY DAMAGE, INJURY OR DEATH.
320.340.6464 DURING SPRAYING • Over Application: DO NOT over apply pesticide. Apply at a rate recommended by chemical manufacturer. Excess pesticide can be dangerous to humans, damage desirable plants, and contaminate soil and water sources. • Never Point Spray Gun: NEVER point the spray gun at people or animals. • Children & Pets: ALWAYS exercise extra caution when spraying near areas accessible to children and pets.
320.340.6464 PREPARING SPRAYER USING SPRAYER (CONTINUED) • Review Safety Information: Review safety information in this manual and manufacturer chemical label before use. • Sprayer Attachment: Ensure the sprayer is securely attached to the vehicle. • Empty Tank: Ensure the sprayer has been thoroughly flushed and drained of all residual chemical prior to uses. • Clean Suction Strainer: Clean suction strainer of any chemical residue with fresh water. USE RUBBER GLOVES for extra safety.
320.340.6464 OPERATION - CLEANING, DECONTAMINATING & STORAGE SPRAYER STORAGE When done using the sprayer, it is always important to clean the sprayer and decontaminate yourself. Do not store the sprayer with chemicals in the tank, as it is unsafe and could also result in damage. Prepare the sprayer for end-of-season storage by running RV anti-freeze through the system. This will keep internal parts lubricated, protect against corrosion, and keep the unit from freezing.
320.340.
320.340.6464 BREAKDOWN 50 GALLON UTV SPRAYER ID Part Number Description Qty ID Part Number Description 1 1124DAB100 Pressure Gauge 1 13 33-103220 Drain Cap Gasket Qty 1 2 33-100025 Square U-Bolt 2 14 33-103910 50 Gallon Tank 1 3 31-100411 Spray Gun Bracket 1 15 3E34 3/4” MGHT x 1/2” MPT Adapter 1 4 31-100412 Tank Strap 2 16 EF3000-QA 3.
320.340.
320.340.
PLEASE FOLLOW ALL WARNINGS IN THIS MANUAL, FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE &320.340.6464 INJURY. 320.340.
