OPERATING GUIDE for your NAPCO FREEDOM F-64TPG Garage Touchpad Home Security System SYSTEM READY 10/15/06 12:05PM R Freedom F-64TPG Touchpad © NAPCO 2006 PATENTED OI320A 9/06 1 F-64TPG_OI320A.03_USER_2...
INTRODUCTION Congratulations on your purchase of a new Freedom Garage Door Security System. This revolutionary new concept in residential security makes using your system easier than ever before possible, because the system uses its computerized control panel to continually monitor the status of your garage door.
T AB L E O F C O N T E N T S TABLE OF CONTENTS INTRODUCTION................................................................................ 2 TESTING THE SYSTEM.................................................................... 2 GARAGE TOUCHPAD INDICATORS AND CONTROLS .................. 4 ARMING WHEN LEAVING ................................................................ 6 BYPASSING FAULTED ZONES ....................................................... 7 ARMING STAY: PROTECTING YOURSELF AT HOME...........
F - 6 4 T P G T O U C H P AD C O N T R O L S & I N D I C AT O R S 1 18 19 20 21 BYPASS FIRE FIRE TBL SYS TBL 22 2 SYSTEM READY 10/15/06 12:05PM 14 15 3 16 5 6 10 7 11 12 8 4 9 4 17 13 4 F-64TPG_OI320A.03_USER_2...
F - 6 4 T P G T O U C H P AD C O N T R O L S & I N D I C AT O R S 1 2 3 4 5 6 LCD Window – 32 character LCD displays system status messages, zone descriptions, system troubles, etc. STATUS Light. Lights (green) to indicate that the system is ready for arming. If a zone is not secured, the light will be off and the zone will display in the window. If a zone has been bypassed, the STATUS light will blink while armed. ARMED Light. Lights (red) to indicate that the system is armed.
A R M I N G W H E N L E AV I N G If you are leaving with no other family members remaining home: 1 2 SYSTEM READY Check the Touchpad indicators. The green STATUS light must be ON-STEADY, and the LCD display will read "SYSTEM READY", indicating that the system is ready to arm. • If the green STATUS light is off and zones are scrolling in the display, a perimeter zone is faulted or a monitored deadbolt (other than your exit door) is unlocked.
B Y P AS S I N G F A U L T E D Z O N E S If you are trying to arm with a faulted zone or zones, the LCD display will clearly indicate which zone(s) are faulted. If you cannot repair the zone(s), they may be temporarily removed from the system, or bypassed, using the following procedure: 1 2 3 Press the BYPASS button. BYPASS YES× NOØ BYPASS 4 "Press down arrow to scroll through zone list and press BYPASS to select zone to bypass" The LCD window will list all zones in your system.
A R M I N G S T A Y : P R O T E C T I N G Y O U R S E L F AT H O M E Arming in the Stay mode allows you to remain home with the perimeter protection active but with the interior protection off, so that you may move freely within the premises. Arm Stay at the Garage Touchpad as follows: 1 2 Check the Touchpad indicators. The green STATUS light must be ON-STEADY, and the LCD disSYSTEM READY play will read "SYSTEM READY", indicating that the system is ready to arm.
A R M I N G AN D L E AV I N G W I T H O T H E R S S T A Y I N G If you are arming and leaving with other family members remaining home: 1 2 SYSTEM READY Check the Touchpad indicators. The green STATUS light must be ON-STEADY, and the LCD display will read "SYSTEM READY", indicating that the system is ready to arm. • If the green STATUS light is off and zones are scrolling in the display, a perimeter zone is faulted or a monitored deadbolt (other than your exit door) is unlocked.
E X I T I N G W I T H T H E S Y S T E M AL R E A D Y A R M E D If the system is Armed STAY and you are leaving with other family members remaining home: 1 Press the STAY button. STAY ARMED The Touchpad will voice prompt the correct action. "The system is arming in Stay mode" The red ARMED light will turn on steady, indicating that you have up to 3 minutes to exit through the garage and close the door. 2 Open the garage door from the inside. System will disarm. 3 Exit the garage.
E X I T I N G W I T H T H E S Y S T E M AL R E A D Y A R M E D If the system is Armed STAY and you are leaving with NO other family members remaining home: 1 Press the AWAY button. AWAY The Touchpad will voice prompt the correct action. • If you change your mind after pressing AWAY, press SILENCE to clear arming. ARMED The red ARMED light will turn on steady, indicating that you have up to 3 minutes to exit through the garage and close the door. 2 Open the garage door from the inside.
EMERGENCY BUTTONS Emergency Buttons (Only available if programmed). The Emergency Buttons, if programmed, are always active, whether the system is armed or disarmed. The Emergency Button must be Held Down for 2 seconds to activate the emergency alarm and transmit the signals to central station. Fire Emergency Hold down the Fire button to alert the central station of a fire emergency.
D I S AR M I N G T H E S Y S T E M DISARMING WHEN RETURNING HOME: When returning home, open your garage door from the outside to automatically disarm the system. The red ARMED light turn off and the green STATUS light will turn on. If an alarm has occurred while you were away, opening the garage door will initiate an entry delay sequence. The I-FOB must be used to disarm the system or an alarm will be initiated within a short interval.
S I L E N C I N G A N AL AR M If an alarm occurs while you are at home: ALARM The Touchpad siren will sound and the red ARMED light will flash. The LCD display will read "ALARM". Proceed with caution! If you suspect that an intruder may still be in the premises, leave immediately and call authorities from a neighbor's telephone. To silence the alarm, insert your I-FOB key into the I-FOB slot on the face of the Touchpad and remove when alarm has silenced.
FIRE PROTECTION* FIRE 1 2 3 4 If a fire is detected, the siren will sound a distinct pulsating tone and the LCD window will flash the word FIRE. If a Fire Alarm does occur: If a fire is in progress, evacuate the premises immediately! Call the Fire Department from an outside phone. If there is no evidence of a fire, press RESET OR insert your I-FOB key into the Touchpad.** The siren will silence, and the word FIRE in the Touchpad LCD window will stop flashing.
FIRE PROTECTION Preparing a Fire Escape Plan Even with the most advanced fire alarm system, adequate protection requires an escape plan. To prepare your plan, draw floor plans of your building. Show two exits - a front or back door and a window from each room. (Make sure the window works. You may need a special fire-escape ladder if the window is high up). Write down your outside meeting place. Family Rehearsal Rehearse each of the following activities: 1. Everyone in his room with the doors closed. 2.
T O U C H P AD M E N U M O D E The Touchpad can provide access to a wide assortment of utility functions, each displayed on the Touchpad LCD window in a prompting “YES/NO” format. 1 To enter Touchpad Menu Mode, press MENU. 2 To skip a function, press NO. 3 To select and execute a function, answer YES. • Press RESET to return to normal Touchpad operation. The Touchpad will automatically return to its normal operating mode if no activity is detected for longer than one minute.
T O U C H P AD M E N U M O D E continue to chime when system is armed. CHANGE KEYPAD BEEP VOLUME Y/N CHANGE VOICE VOLUME ACTIVATE SIREN TEST DISPLAY FIRE ALARM DISPLAY FIRE TROUBLE Y/N Y/N CHANGE KEYPAD BEEP VOLUME - When the Touchpad buttons are pressed or when an entry warning activates, the Touchpad beeper sounds. This function allows the Touchpad beeper volume to be adjusted. Press YES to increase, press NO to decrease. Selections are HIGH, MED-HIGH, MED, LOW and OFF.
T O U C H P AD M E N U M O D E ACTIVATE FAULT FIND RESET SYSTEM TBL ACTIVATE DIALER TEST ENTER LOG MENU ACTIVATE PROGRAM Y/N Y/N Y/N Y/N Y/N ACTIVATE FAULT FIND - Activates a multiple diagnostic test report. For installer's use only. If accidentally enabled, press RESET to exit. Note: This selection only appears with a Master I-FOB inserted in the Touchpad. RESET SYSTEM TBL - System troubles display and sound at the Touchpad.
T O U C H P AD M E N U M O D E ACTIVATE DOWNLOAD Y/N ACTIVATE LOST KEY MODE Y/N ACTIVATE PIR TEST Y/N ACTIVATE DOWNLOAD - For installer's use only. If accidentally enabled, press RESET to exit. Note: This feature is disabled while armed. Note: This selection only appears with a Master I-FOB inserted in the Touchpad. ACTIVATE LOST KEY MODE - In the event that the keys to your deadbolt are lost or stolen, the system may still be used by arming in the Lost Key Mode.
USER PROGRAM MODE User Program Mode Your Installer has programmed into your system a uniquely coded digital Master I-FOB that can be used to not only disarm the system and silence the siren, but also allows access to the User Program Mode. User Program Mode allows you to program various options, such as adding other User Codes, setting the system Time and Date, enrolling new I-FOB's, etc.
USER PROGRAM MODE to the right. 2. Repeat this process to increment (or decrement) the minute as needed. Press ENTER move the cursor to the right and press the YES or NO buttons to toggle between "A" and "P" (for AM and PM). When finished, press MENU to save and proceed to the next option, "ENROLL MASTER I-FOB Y/N".
USER PROGRAM MODE to the system. Create a User I-FOB as follows: 1. Obtain a new I-FOB from your security professional (order part F-IFOB). 2. With “CREATE USER I-FOB Y/N” displayed in the LCD window, press "Y" and the LCD window will request to insert the new I-FOB into the Touchpad. 3. After 5 seconds, the I-FOB will be programmed, and you will be prompted to remove the I-FOB from the Touchpad.
SYSTEM TROUBLE ERROR CODES Your control panel is capable of detecting a variety of troubles that may affect system performance. In the unlikely event that a problem should occur, the SYS TBL (system trouble) icon will display on the left side of Touchpad window along with one or more of the following error codes. If the problem is related to a specific zone or device, the corresponding number will also be indicated.
SYSTEM TROUBLE ERROR CODES Trouble Indication System Trouble Condition Action E04-NN Wireless Transmitter Supervisory Failure A problem has been detected with a wireless transmitter. Call installing company for service E05-NN Wireless Transmitter Low Battery The battery in a wireless transmitter is low and should be replaced. This transmitter is on the zone corresponding to the number NN.
SYSTEM TROUBLE ERROR CODES Trouble Indication System Trouble Condition Action E10-NN Touchpad Response Failure Call installing company for service. E11-NN Touchpad Tamper A keypad or Touchpad has been removed from the wall. Call installing company for service if problem cannot be repaired. E12-NN Expansion Zone Module Response Failure Call installing company for service. E13-NN Expansion Module Tamper The cover has been removed from a zone expansion module.
SYSTEM TROUBLE ERROR CODES Trouble Indication E19-00 System Trouble Condition Action User Program Memory Call installing company for service. Error E20-00 Dealer Program Memory Error Call installing company for service. E21-00 System Shutdown Call installing company for service. E22-NN Sensor Watch Activity A Motion Sensor on the zone indicated has failed the programmed Sensor Watch activity test.
SYSTEM TROUBLE ERROR CODES Trouble Indication System Trouble Condition E40-00 RF Self Test Failure E41-NN Fire Trouble E51-00 Bell/Siren Trouble There is a problem with the Bell or Siren. Call installing company for service. E58-00 Telemetry Trouble Call installing company for service. E59-00 Telemetry Failure Call installing company for service. E66-00 E99-00 Action A wireless motion sensor on the zone indicated has failed its automatic self test routine.
USER I-FOB LIST • The space below is for recording the names of those in possession of User I-FOB's in your system. If an I-FOB is lost, be sure to delete its I-FOB number from the system (using the procedure on the previous page) as soon as possible.
L O S T G AR AG E D O O R O P E N E R M O D E Lost Opener Mode In the event that your garage door remote control (or key that operates your garage door opener) is lost or stolen, the system may still be used by arming in the Lost Garage Door Opener Mode. In Lost Garage Door Opener Mode, the system may be armed as usual. However, manually opening the garage door will not disarm the system. The system may only be disarmed with the I-FOB digital key.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 STATEMENT This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. This equipment uses the following jacks: An RJ31 X is used to connect this equipment to the telephone network.
WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: • Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. • Intrusion detectors (e.g.
WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM (Continued) • Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the situation. In the case of a monitored alarm system, authorities may not respond appropriately. • This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time.
NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
written, are either merged herein or are expressly cancelled. NAPCO neither assumes, nor authorizes any other person purporting to act on its behalf to modify, to change, or to assume for it, any other warranty or liability concerning its products. In no event shall NAPCO be liable for an amount in excess of NAPCO's original selling price of the product, for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure of the product.
THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits for a Class-B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
NOTES 37 F-64TPG_OI320A.03_USER_2...
NOTES 38 F-64TPG_OI320A.03_USER_2...
NOTES 39 F-64TPG_OI320A.03_USER_2...
333 Bayview Avenue Amityville, New York 11701 For Sales and Repairs, (800) 645-9445 For Technical Service, (800) 645-9440 R Publicly traded on NASDAQ Symbol: NSSC © NAPCO 2006 40 F-64TPG_OI320A.03_USER_2...
