User's Manual

ManualsBrandsMaster Lock ManualsElectronics3681

www.masterlock.com

Master Lock Company LLC, Milwaukee, WI 53210 U.S.A. | 800-308-9244

Master Lock Canada, Oakville, Ontario L6H 5S7 Canada | 800-227-9599

P52953

1. Open box

• To prevent damage to the lock, DO NOT USE a sharp object to open packaging

• Keypad module and lock module will be in same package

2. Remove keypad module and lock module from package

3. Open locker door

4. With one hand, align front housing through 2 mounting holes on the front of the locker door. (A)

• Pull the connection ribbon through the large middle mounting hole

• Note: The diameter of the mounting holes must be 7/32in minimum for proper installation

and ﬁt. If the holes are undersized, a 7/32in drill bit can be used to widen them.

5. With your other hand, line up the lock module on the back of the door and attach the

connection ribbon (B)

6. Feed excess ribbon cable back into center mounting hole (C)

7. Line up the threaded screws from the keypad module with the holes in the lock module (D)

8. Install nuts on the threaded screw and tighten with 3/8in nut driver (E)

• Note: Tighten fastener to a maximum torque of 3N-m (20-25in-lbs) to avoid product damage

or lock failure

9. Close locker door

10. Test lock for functionality (Refer to Multi-User and Single-User Instructions)

Notes:

1. Battery included

2. Lock is conﬁgured to work on 1/32in, 1/2in, and 3/4in door depths

3. Lock is conﬁgured to work on left and right hinged doors

(D)

(E)

1. Low Battery

2. Settings Mode

3. Locked

4. Unlocked

5. Single-User Mode

6. Bluetooth Mode -

ADA Model Only

(FOB Required)

7. Invalid Code

8. Bolt Jam

9. Entered Code

10. Awaiting Code

1. Low Battery

2. Settings Mode

3. Locked

4. Unlocked

5. Single-User Mode

6. Bluetooth Mode -

ADA Model Only

(FOB Required)

7. Invalid Code

8. Bolt Jam

9. Entered Code

10. Awaiting Code

1. Low Battery

2. Settings Mode

3. Locked

4. Unlocked

5. Single-User Mode

6. Bluetooth Mode -

ADA Model Only

(FOB Required)

7. Invalid Code

8. Bolt Jam

9. Entered Code

10. Awaiting Code

Display Screen Key

10 9

Notice: This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept

any interference including interference that may cause undesired operation of the device.

Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Changes or modiﬁcations made to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

any interference including interference that may cause undesired operation of the device.

interference received, including interference that may cause undesired operation.

Changes or modiﬁcations made to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

any interference including interference that may cause undesired operation of the device.

interference received, including interference that may cause undesired operation.

Changes or modiﬁcations made to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

The Bluetooth

word mark and logos

are registered trademarks owned by

Bluetooth SIG, Inc. and used under

license by Master Lock Company LLC.

La palabra marca Bluetooth

y los logos son marcas registradas

de propiedad de Bluetooth SIG, Inc.

y utilizadas bajo licencia por

Master Lock Company LLC.

Le mot servant de marque Bluetooth

et les logos sont des marques

enregistrétés de Bluetooth SIG, Inc.

et, utilisés sous license par

Master Lock Company LLC.