Replacement Part List

“D SERIES” HG
Master Appliance Corp.
2420 18
th
St.
Racine, WI 53403-2381 USA
Tel: [phone]
Email: [e-mail]
www.masterappliance.com
58278E REV A
pg. 1 of 6
Available kits
Motor Replacement- Part No’s. 30073 (120V), 30074 (220-240V)
Element Connector Replacement– 30089, 30090 (HG-801D only)
Switch & Bezel Kits Replacement– 30075
Cordset Replacement-– 30079 (120V 15 Amp), 30080 (120V 20 Amp),
30081 (220V UL/CUL), 30097 (220-240V EU), 30098 (220-240V UK)
Nozzle shield replacement 30077
Handle Replacement 30091
What’s in the kit
MOTOR KIT:
• MOTOR, (1)
• SCREW, #6-32 x .50 LONG (2)
• SCREW, M3 x 0.5 x 10mm LONG (1)
• CABLE TIE (2)
• SHRINK TUBE (1)
CORDSET KIT:
• CORDSET (1)
• CABLE GUARD (1)
• SCREW, #6-32 x .31 GREEN (1)
• CABLE TIE (2)
• SHRINK TUBE (1)
• CORD CLAMP, USED WITH (220 – 240 VAC) units (1)
NOZZLE SHIELD KIT
• NOZZLE ASSEMBLY, (1)
• SHIELD, (1)
• SCREW, #6-32, (2)
HANDLE KIT
• HANDLE SET RT & LT (1)
• SCREWS, #6-19, (4)
ELEMENT CONNECTOR KIT:
• ELEMENT CONNECTOR ASSY (1)
• CABLE TIE (2)
• SHRINK TUBE (2)
SWITCH & BEZEL KIT:
• SWITCH/BEZEL/JUMPER ASSY (1)
• BARRIER, ELECTRICAL (1)
MASTER HEAT GUN REPLACEMENT PARTS AND ACCESSORIES ARE ENGINEERED AND MANUFACTURED TO PRECISE MASTER APPLIANCE SPECIFICATIONS. REPLACEMENT PARTS AND ACCESSORIES FROM
OTHER MANUFACTURERS ARE NOT PRODUCED TO THESE PRECISE SPECIFICATIONS. FAILURE TO USE MASTER APPLIANCE REPLACEMENT PARTS OR FAILURE TO INSTALL MASTER APPLIANCE REPLACEMENT
PARTS EXACTLY AS INSTRUCTED MAY CAUSE PHYSICAL INJURY OR DAMAGE TO THE HEAT GUN. MASTER APPLIANCE CANNOT ASSUME RESPONSIBILITY FOR PHYSICAL INJURY OR DAMAGE TO THE HEAT GUN
RESULTING FROM THE USE OF ANY OTHER BRAND OF REPLACEMENT PART OR IMPROPER INSTALLATION OF MASTER APPLIANCE REPLACEMENT PARTS OR ACCESSORIES.
WARNING: Disconnect heat gun power cord and allow the heat gun to cool before disassembly.
READ THE SERVICE INSTRUCTIONS CAREFULLY. FAILURE TO EXACTLY FOLLOW THE INSTRUCTIONS
COULD RESULT IN PERSONAL INJURY OR DAMAGE TO YOUR HEAT GUN. ALL REPAIRS MUST BE
PERFORMED BY A QUALIFIED REPAIR TECHNICIAN.
AVERTISSEMENT : Débrancher le cordon du pistolet thermique et laisser celui-ci refroidir avant de le
démonter.
LIRE ATTENTIVEMENT LES INSTRUCTIONS D’ENTRETIEN. OMETTRE D’OBSERVER EXACTEMENT CES
INSTRUCTIONS POURRAIT ENTRAÎNER DES BLESSURES OU ENDOMMAGER VOTRE PISTOLET THERMIQUE.
SEUL UN RÉPARATEUR QUALIFIÉ PEUT EFFECTUER LES RÉPARATIONS.
ADVERTENCIA: Desconecte el cable de la pistola térmica y deje que ésta se enfríe antes de desarmarla.
LEA CON ATENCIÓN LAS INSTRUCCIONES DE SERVICIO. EL NO SEGUIR EXACTAMENTE LAS
INSTRUCCIONES PUEDE RESULTAR EN DAÑO A LA PISTOLA TÉRMICA. TODAS LAS REPARACIONES DEBEN
SER REALIZADAS POR UN TÉCNICO DE REPARACIONES CALIFICADO.
Do not touch
nozzle until cool
Ne pas toucher la
buse avant qu’elle
ait refroidi
No toque
la boquilla hasta que
se haya enfriado
TOOLS REQUIRED
#1 DRIVE PHILLIPS
SCREWDRIVER
#2 DRIVE PHILLIPS
SCREWDRIVER
1/8 inch HEX KEY
(ALLEN WRENCH)
UTILITY KNIFE