User manual

ManualsBrandsMASCOT ManualsBattery ChargersVRLA charger Blei-Lader 36 V, 2,3 A 36 V Lead-acid, SLA, Lead acid membrane

• Output cables having a modular plug ( similar to

a telephone connector) must never be connec-

ted to a telephone outlet.

• Products with a welded plastic housing are

not repairable. Please contact your supplier for

replacement part.

• This product contains hazardous voltages and

there are no user replaceable parts inside the

product. Never attempt to remove the cover.

• WARNING: No modiﬁcation of this equipment is

allowed. Any repair/service should be carried out

by qualiﬁed personnel who may get assistance

by contacting the manufacturer or the manu-

facturer’s agent.

• Products speciﬁed to have automatic polarity

protection must be switched off if a battery is

connected with reverse polarity. The protection

will be automatically reset when the polarity has

been corrected.

• In chargers speciﬁed to have a replaceable fuse

as polarity protection the fuse must be replaced

if the battery has been connected with reverse

polarity. When replacing the fuse; a fuse of the

same type and rating must be used.

• If the product is speciﬁed to comply with the

standard for Medical Electrical Equipment (stan-

dards based on IEC60601-1) it complies with

some of the requirements for medical electrical

equipment and may be used in medical applica-

tions and hospital environments.

• The product must not be used in the vicinity of

ﬂammable anesthetic gases or in other environ-

ments with ﬂammable or explosive atmosphere.

• If the product is speciﬁed to comply with the

standard for Medical Electrical Equipment

for Home Healthcare Environment (standard

IEC60601-1-11) it may be used in medical

applications used in a home healthcare environ-

ment.

NOTE: Products relying on safety earth for

protection (Class I) may not be used in home

healthcare environment unless they are perma-

nently wired to the building installation:

Installation must only be carried out by qualiﬁed

service personnel, following the below instructions:

- The protective earth conductor must be min.

0.75 mm

- Connect the protective earth conductor to the

external protective earthing system.

- Verify that the protective earth terminal used is

connected to the external protective earthing

system.

- Verify the integrity of the external protective

earthing system.

• This product converts the mains voltage to

a safety extra low voltage.

The output from products applying with 2MOPP

insulation ( model names followed by ”P”) may

be treated as Applied Part Type B or Type BF

according to standard EN/IEC 60601-1 and

may come in physical contact with a patient.The

housing of the product shall not be allowed to

contact the patient.

• This product must be operated in an environ-

ment within temperature range +5 to +40°C,

humidity 15 - 93 % RH and atmospheric pres-

sure 70 - 106 kPa (700 - 1060 hPa).

• Expected service life of this product and acces-

sories delivered with this product is three (3)

years, if operated as indicated above. However;

the guarantee times indicated in document

”TERMS OF SALES AND DELIVERY FOR MAS-

COT AS” apply (available at www.mascot.com).

• Environmental parameters during transport and

storage between uses: temperature range -25 to

+85 °C, humidity 15 - 93% RH NC and atmosp-

heric pressure 70 - 106 kPa (700 - 1060 hPa).

• If stored for longer periods of time the

environmental parameters should be within

the temperature range +5 to +35°C, humidity

range 10 - 75% RH NC and atmospheric pres-

sure 70 - 106 kPa (700 - 1060 hPa) to maintain

the products expected service life.

• Expected shelf life of this product is one (1) year,

if stored as indicated above.