OPERA TING OPERATING INSTRUCTIONS FOR THE X-07/CEX -07 -07/CEX-07 HIGH SECURITY ELECTRONIC LOCK (TYPE 1F) Please read all instructions carefully before putting your X-07/CEX-07 into operation.
TABLE OF CONTENTS OPENING THE X-07 USING THE PRE-SET COMBINATION ............... 3 If You Pass Your Target Number When Dialing ............................... 5 Redial Entire Combination If... ......................................................... 6 SETTING OPERATING MODE AND NEW COMBINATIONS ................ 7 Setting the Operating Mode ............................................................ 7 Alternate Method to Set Operating Mode ........................................ 9 Setting Combinations ...
OPENING THE X-07 USING THE PRE -SET COMBINA TION PRECOMBINATION TO OPEN THE X-07: 1. Dial left (counterclockwise) 4-6 turns to “power up” the lock. Numbers will appear on the LCD display screen. 3 OPENING THE X -07 X-07 Your X-07 lock has been shipped pre-set in the Single Combination Mode with the combination set to 50-25-50. Practice opening the lock several times before you set a new combination.
OPENING THE X -07 X-07 2. Continue dialing left to the first number in the combination (50). Stop. The number 50 will be displayed on the screen. 3. Now dial in the opposite direction (right, clockwise) to 25. Stop. 4. Now dial left to 50. Stop. 5. Now dial right. After OP (OPen right) appears on the display screen, continue dialing to the right to pull the lock bolt.
IF Y OU P ASS Y OUR T ARGET NUMBER WHEN DIALING YOU PASS YOUR TARGET A. Example: target number-25. If you pass your target number by 4 or more (photo 1), continue dialing in the same direction (photo 2), until you reach the target number again (photo 3). B. Example: target number-25. If you pass the target number by no more than 3 numbers (photo 1), you may reverse directions slowly (photo 2) and the display will “jump back” 4 numbers (photo 3).
REDIAL ENTIRE COMBINA TION IF ... COMBINATION A. The Lightning Bolt symbol is displayed. B. The screen goes blank before the lock bolt is withdrawn. When you feel comfortable opening the X-07 using the pre-set combination, you are ready to put the lock into operation.
SETTING OPERA TING MODE AND OPERATING NEW COMBINA TIONS COMBINATIONS SETTING THE OPERA TING MODE OPERATING Use the Change Key (photo 1) provided with your X-07 to set the desired operating mode and combinations. If at any time during the process you see the Key and Lightning Bolt symbols displayed (photo 2), stop the sequence and return to Step 3. If at any time you see a Lightning Bolt symbol displayed (photo 3), stop and return to Step 2. 1. Retract the bolt by entering the correct combination(s).
SETTING OPERA TING MODE AND NEW COMBINA TIONS OPERATING COMBINATIONS (The first time use the pre-set combination: 50 left-25 right-50 left). NOTE: Release the bolt mechanism on the container so the dial will turn freely. Different containers have different release mechanisms. 2. Insert the Change Key into the slot on the back of the lock. 3. Dial to the left (counterclockwise). The Change Key symbol will appear in the display. The lock will never open when the Change Key symbol is displayed. 4.
AL TERNA TE METHOD TO SET OPERA TING MODE ALTERNA TERNATE OPERATING This alternate method replaces steps 1-4. If you have lost or forgotten the current combination and have access to the back of the lock, you can select a mode of operation to set new combinations using the serial number found on the inside cover of the lock. This serial number will not open the lock; it will only allow you to set new combination. A. Dial an incorrect combination to obtain the Lightning Bolt error symbol. B.
5. Dialing right, the symbol SL (for Select Mode) will be displayed (photo 1). Now dial left to select the mode of operation: 1 — for Single Combination Mode (photo 2) 2 — for Dual Combination Mode (photo 3) 3 — for Supervisory/Subordinate Mode (photo 4) 6. Stop on the number of your selection. Now dial right to set the mode. The symbol EC or El will be displayed depending upon the mode selected. SETTING COMBINA TIONS COMBINATIONS 7a.
(2) The display will flash the new combination three times and then display the symbol PO (for Pull Out Change Key) (photo 1). Remove the Change Key (photo 2). This will cause the Change Key symbol to disappear. The display will show the symbol CC (Confirm Combination(s)) (photo 3). (3) To confirm the combination(s), redial the new combinations. When the symbol OP (OPen right) appears on the display, continue dialing to the right to retract the bolt. The combination is now set. 7b.
The display will flash the new combination three times then show the symbol E2 (Enter second combination). (2) Dial the new second combination in the correct sequence: (Example 25-50-75) Dial: Left to the first number. Stop. (photo 1) Right to the second number, Stop. (photo 2) Left to the third number. Stop. (photo 3) Right until display flashes the new combination. (photo 4) The display will flash the new combination three times, then display the symbol PO (Pull Out Change Key).
(3) Remove the Change Key. This will cause the Change Key symbol to disappear. The display will show the symbol CC (Confirm Combination(s)). (4) To confirm the combinations, redial the new combinations: In Dual Combination Mode: Dial either of the new combinations (photo 1). The symbol E2 (Enter second combination) will be displayed (photo 2). Enter the remaining combination (photo 3). In Super/Sub Mode: Dial Supervisory combination first (photo 1).
When the display stops flashing, it will re-display EC, E1 or E2 depending upon which combination you were entering. Now reinsert the Change Key and dial in the new combination of your choice. NOTE: If you misdial or do not properly finish the Change Key sequence in any way, the X-07 automatically reverts to the previous combination(s). The old combination remains valid until a new combination is confirmed. Let the lock completely power down and then try the combination again.
USING THE X -07 X-07 SINGLE COMBINA TION MODE COMBINATION In this mode the X-07 functions much like a standard combination lock. It will open any time the three-number combination is correctly dialed. Dial left to “power up” the lock. 15 X-07 USING THE X -07 When numbers appear on the display, continue dialing: (Example 25-50-75) Dial: Left to the first number. Stop. (photo 1) Right to the second number. Stop. (photo 2) Left to the third number. Stop.
DU AL COMBINA TION MODE DUAL COMBINATION In this mode, two combinations must be correctly and consecutively entered to open the lock. Either combination may be entered first. However, the operator must begin entering the second combination within 40 seconds of the first combination. USING THE X -07 X-07 First Operator: Dial left to “power up” the lock. When numbers appear on the display, continue dialing: (Example 25-50-75) Dial: Left to the first number in the first combination. Stop.
If the dial remains stationary for more than 40 seconds the computer will reset (LCD will go blank) requiring the operator to redial both combinations. If you pass your number when dialing, please refer to page 3 or 18 for assistance. SUPERVISORY/SUBORDINA TE MODE SUPERVISORY/SUBORDINATE In this mode, two combinations must be correctly dialed to open the lock. However, the Supervisory Combination must be dialed first to display UL (Unlocked).
Subordinate Operator: Dial: (Example 30-60-90) Left to the first number in the Subordinate combination. Stop. (photo 1) Right to the second number in the Subordinate combination. Stop. (photo 2) Left to the third number in the Subordinate combination. Stop. (photo 3) Right to OP (photo 4); continue right to pull the bolt. (photo 5) The X-07 will continue to open as often as the Subordinate combination is redialed; that is, until the Super Combination is redialed displaying LU (Locked Up).
Left to the third number in the Supervisory combination. Stop. (photo 3) Right to LU (Locked Up) symbol is displayed. (photo 4) This blocks entry of the Subordinate Combination holder(s) until the Supervisory Combination is redialed redisplaying UL (Unlocked). There may be unlimited delay between dialing of the Supervisory combination and dialing of the Subordinate combination.
requiring the operator(s) to redial that combination. If you pass your number when dialing, please refer to page 18 for assistance. IF Y OU P ASS Y OUR T ARGET NUMBER WHEN YOU PASS YOUR TARGET DIALING A. Example: target number-25. If you pass your target number by 4 or more (photo 1), continue dialing in the same direction (photo 2), until you reach the target number again (photo 3). B. Example: target number-25.
reverse directions slowly (photo 2) and the display will “jump back” 4 numbers (photo 3). Now you may dial slowly in the original direction to the target number (photo 4). USING THE A UDIT FEA TURES AUDIT FEATURES OF Y OUR X -07 YOUR X-07 CHECK THE NUMBER OF SUCCESSFUL OPENINGS Dial Right when the lock is powered down (screen blank and no dialing for 2 minutes). After the lock is powered up it will alternately flash two pairs of numbers.
USING THE A UDIT FEA TURES OF Y OUR X -07 AUDIT FEATURES YOUR X-07 cessful opening count. The number with the arrow flashing right represents the last two numbers in the opening count. For example: 00 (arrow left) and 15 (arrow right) means the lock has been successfully opened a total of 0015 times. The successful openings count does not re-set. The number will reflect the total number of times the X-07 has been opened since it was manufactured.
GUIDE TO SYMBOLS Blank Display The lock has been reset or is powered down. OP Open Right Lightning Bolt Incorrect Combination Dialed. (When this symbol appears in the upper left corner of the display, simply redial combination.) UL Unlocked GUIDE TO SYMBOLS LU Lock Up Key Change Key Symbol (The Change Key has been inserted and the lock is in Change Combination Mode.
CE FUNCTION The covert entry function is used to indicate that the normal operation of the X-07 has been compromised. The following section describes the unique operations of the CEX-07. You should be familiar with the operation of the X-07 as described in the preceding sections. NORMAL OPERA TION OPERATION 1. Start dialing to the left (CCW). The lock will display CA if access is allowed to the lock. If CE is displayed, refer to the section on covert entry below. 2.
RESETTING COVERT ENTRY AND COVERT ENTRY COMBINA TION CHANGE COMBINATION This procedure works only if the lock is powered down with the Change Key out of the lock. Dialing to the right (CW) on lock startup will display the open counter. If the open counter is not displayed, the lock has not yet powered down. If there is a covert entry or the Change Key is in, continuing to dial to the right will result in dialing an ID. The ID is selected when direction is reversed.
3. Dial the new CE reset combination. Pull Out Change Key (PO) will be shown. 4. Pull out the Change Key. Confirm new CE reset combination (CC) will be shown. 5. Dial the new CE reset combination. This will change the CE reset combination. It does not clear the CE condition on the lock. The CE reset combination can be used once the lock has powered down. GUIDE TO SYMBOLS - CE FUNCTION CE A Covert Entry condition exists. CA Covert Entry detection is active and access to the lock is allowed.
Document Number 000.111 Rev. D 11/98 Converted to Acrobat 08/00 Notice: The information in this manual is subject to change without notice and does not represent a commitment on the part of Mas-Hamilton Group (MHG). MHG shall not be liable for technical errors or omissions contained herein; not for incidental or consequential damages resulting from the furnishing, performance or use of this material. © 1997, 1998 Mas-Hamilton Group® All rights reserved www.mas-hamilton.
