Dimensions Guide

www.marvelrefrigeration.com24” Marvel Professional All Freezer Model # MP24FA 800.223.3900
1/16/Rev. a
Overlay Panels
14
!
CAUTION
1
5
⁄32"
(2.9 cm)
Figure 17
Right Hand Hinged Door
24" (61 cm) wide appliance
Figure 18
Right Hand Hinged Door
24" (61 cm) wide appliance
OVERLAY DOOR PANEL INSTALLATION
1" (2.5 cm) diameter
x
1
⁄4" (6 mm) deep
4 places
Clearance
for hinge
at top and
bottom
2"
(5.1 cm)
3
11
⁄16"
(9.4 cm)
1
1
⁄2"
(3.8 cm)
typical
1
⁄4"
(6 mm)
Deep
Hinge side of door
Clearance for
screw head,
4 places
30
11
⁄32"
(77.1 cm)
1
11
⁄16"
(4.3 cm)
23
3
⁄4"
(60.3 cm)
3
1
⁄8"
(7.9 cm)
Top of door
Step 4: Assemble the panel to the door
The preferred method of attaching the panel to the door
is to clamp the panel to the door so it cannot move while
drilling the screw pilot holes. Use bar clamps or "C" clamps
with pads on the clamping surfaces that will not mar the
panel or the door. The custom overlay panel should be
ush with the top of the door and centered along the width
of the door. See Figure 10a. Drill holes through the gasket
extrusion using the 10 holes as pilot holes. Use the drill
size from the chart in Table "C", being careful not to drill
through the front surface of the panel, drill no deeper than
1
⁄2" (12.7 mm) deep. If the overlay panel is thinner than
5
⁄8" (16 mm) thick shorter screws will have to be obtained.
Fasten the panel to the door with the 10 screws provided in
the literature pack. (See Figure 19a). Remove the clamps
and replace the gasket in the gasket extrusion channels of
the door. Some force may be required to seat the gasket
into the channels. Be sure the gasket corners are seated
properly.
Material Type #10 Wood Screw
Hardwood
1
⁄8" (3.2 mm) Diameter. Pilot Hole
Softwood
7
⁄64 (2.8 mm) Diameter. Pilot Hole
Table C
Weight of overlay door panel must not exceed 15
pounds (6.8 kg) for a solid door model or 10 pounds
(4.5 kg) for a glass door model.
3
1
⁄8"
(7.9 cm)
1
3
⁄4"
(4.4 cm)
4
1
⁄8"
(10.5 cm)
1
⁄4" (6 mm)
radius is
permissible
This side
to door
3
1
⁄8"
(7.9 cm)
3
27
⁄32"
(9.8 cm)
1
3
⁄16"
(3 cm)
14"
(35.6 cm)
4
7
⁄8"
(12.4 cm)
For comprehensive installation instructions,
please visit www.marvelrefrigeration.com
18
!
CAUTION
Weight of overlay door panel must not
exceed 15 pounds (6.8 kg).
1
5
⁄32"
(2.9 cm)
1
5
⁄32"
(2.9 cm)
OVERLAY DOOR PANEL INSTALLATION
Clearance for
screw head,
4 places
Hinge side of door
Clearance
for hinge
at top and
bottom
Figure 20
Left Hand Hinged Door
24" (61 cm) wide appliance
Figure 21
Left Hand Hinged Door
24" (61 cm) wide appliance
Top of door
1
3
⁄4"
(4.4 cm)
1
⁄4"
(6 mm)
Deep
1" (2.5 cm) diameter
x
1
⁄4" (6 mm) deep
6 places
2"
(5.1 cm)
3
11
⁄16"
(9.4 cm)
1
1
⁄2"
(3.8 cm)
typical
1
11
⁄16"
(4.3 cm)
30
11
⁄32"
(77.1 cm)
1
⁄4" (6 mm)
radius is
permissible
14"
(35.6 cm)
1
3
⁄16"
(3 cm)
3
1
⁄8"
(7.9 cm)
Clearance
for hinge
at top and
bottom
Top of door
Clearance for
screw head,
4 places
Figure 18
Right Hand Hinged Door
24" (61 cm) wide appliance
Hinge side of door
23
3
⁄4"
(60.3 cm)
23
3
⁄4"
(60.3 cm)
Figure 19
Right Hand Hinged Door
24" (61 cm) wide appliance
3
1
⁄8"
(7.9 cm)
1
3
⁄4"
(4.4 cm)
2"
(5.1 cm)
3
11
⁄16"
(9.4 cm)
1
⁄4"
(6 mm)
Deep
30
11
⁄32"
(77.1 cm)
1" (2.5 cm) diameter
x
1
⁄4" (6 mm) deep
4 places
1
1
⁄2"
(3.8 cm)
typical
1
11
⁄16"
(4.3 cm)
4
7
⁄8"
(12.4 cm)
4
7
⁄8"
(12.4 cm)
14"
(35.6 cm)
1
3
⁄16"
(3 cm)
1
⁄4" (6 mm)
radius is
permissible
This side
facing interior
This side
facing interior
18
!
CAUTION
Weight of overlay door panel must not
exceed 15 pounds (6.8 kg).
1
5
⁄32"
(2.9 cm)
1
5
⁄32"
(2.9 cm)
OVERLAY DOOR PANEL INSTALLATION
Clearance for
screw head,
4 places
Hinge side of door
Clearance
for hinge
at top and
bottom
Figure 20
Left Hand Hinged Door
24" (61 cm) wide appliance
Figure 21
Left Hand Hinged Door
24" (61 cm) wide appliance
Top of door
1
3
⁄4"
(4.4 cm)
1
⁄4"
(6 mm)
Deep
1" (2.5 cm) diameter
x
1
⁄4" (6 mm) deep
6 places
2"
(5.1 cm)
3
11
⁄16"
(9.4 cm)
1
1
⁄2"
(3.8 cm)
typical
1
11
⁄16"
(4.3 cm)
30
11
⁄32"
(77.1 cm)
1
⁄4" (6 mm)
radius is
permissible
14"
(35.6 cm)
1
3
⁄16"
(3 cm)
3
1
⁄8"
(7.9 cm)
Clearance
for hinge
at top and
bottom
Top of door
Clearance for
screw head,
4 places
Figure 18
Right Hand Hinged Door
24" (61 cm) wide appliance
Hinge side of door
23
3
⁄4"
(60.3 cm)
23
3
⁄4"
(60.3 cm)
Figure 19
Right Hand Hinged Door
24" (61 cm) wide appliance
3
1
⁄8"
(7.9 cm)
1
3
⁄4"
(4.4 cm)
2"
(5.1 cm)
3
11
⁄16"
(9.4 cm)
1
⁄4"
(6 mm)
Deep
30
11
⁄32"
(77.1 cm)
1" (2.5 cm) diameter
x
1
⁄4" (6 mm) deep
4 places
1
1
⁄2"
(3.8 cm)
typical
1
11
⁄16"
(4.3 cm)
4
7
⁄8"
(12.4 cm)
4
7
⁄8"
(12.4 cm)
14"
(35.6 cm)
1
3
⁄16"
(3 cm)
1
⁄4" (6 mm)
radius is
permissible
This side
facing interior
This side
facing interior
14
OVERLAY DOOR PANEL INSTALLATION
Figure 18
3
1
⁄2"
(89 mm)
Counter bore
lock hole
on back side.
Figure 18a
#10 x
1
⁄2"
screw
1
⁄2" (13 mm) diameter drill
through door panel, from
other side (see detail
above)
13
⁄16" (20.5 mm)
counter bore,
7
⁄16" (11 mm)
deep.
17
⁄32"
(13.7 mm)
Hinge side of door
Table C
Material Type #10 Wood Screw
Hardwood
1
⁄8" (3.2 mm) Diameter. Pilot Hole
Softwood
7
⁄64 (2.8 mm) Diameter. Pilot Hole
Step 4: Assemble the panel to the door
The preferred method of attaching the panel to the door
is to clamp the panel to the door so it cannot move while
drilling the screw pilot holes. Use bar clamps or "C" clamps
with pads on the clamping surfaces that will not mar the
panel or the door. The custom overlay panel should be
ush with the top of the door and centered along the width
of the door. See Figure 13a. Drill holes through the gasket
extrusion using the 10 holes as pilot holes. Use the drill
size from the chart in Table "C", being careful not to drill
through the front surface of the panel. If the overlay panel is
thinner than
5
⁄8" (16 mm) thick shorter screws will have to be
obtained. Fasten the panel to the door with the 10 screws
provided in the literature pack. (See Figure 18a). Remove
the clamps and replace the gasket in the gasket extrusion
channels of the door. Some force may be required to seat
the gasket into the channels. Be sure the gasket corners
are seated properly.