Installation Operation and Maintenance Instructions Ice Machine MO15CRS1XS (Outdoor)
Installation Operation and Maintenance Instructions Contents Service Intro Troubleshooting Warranty Safety Obtaining Service Safety and Warning Disposal and Recycling Installation Environmental Requirements Electrical Cutout Dimensions Product Dimensions Side by Side Installation Water Hookup Anti-Tip Bracket General Installation Grille Installation Door Swing Door Adjust Operating Instructions First Use Ice Airflow and Product Loading Maintenance Cleaning Cleaning Condenser Extended Non-Use 2
Installation Operation and Maintenance Instructions Welcome to the Marvel Experience Congratulations on adding a new Marvel crescent ice maker to your home and thank you for choosing our quality American-built product. You’ll enjoy years of crescent ice in the comfort and convenience of your home, backed by our full worry-free warranty. We are thrilled to welcome you to our growing community of Marvel owners, who trust in our products and our support.
Installation Operation and Maintenance Instructions Disposal and Recycling Safety and Warning ! DANGER NOTICE Please read all instructions before installing, operating, or servicing the appliance. RISK OF CHILD ENTRAPMENT. Before you throw away your old refrigerator or freezer, take off the doors and leave shelves in place so children may not easily climb Use this appliance for its intended purpose only and inside.
Installation Operation and Maintenance Instructions Electrical Cutout Dimensions PREPARE SITE ! WARNING Your Marvel product has been designed for either freestanding or built-in installation. When built-in, your unit does SHOCK HAZARD — Electrical Grounding Required. not require additional air space for top, sides, or rear. Never attempt to repair or perform maintenance on the However, the front grille must NOT be obstructed, and unit until the electricity has been disconnected.
Installation Operation and Maintenance Instructions Product Dimensions Not Including Handle *Add 3/4" To Depth For Water Line Clearance 6
Installation Operation and Maintenance Instructions Side-by-Side Installation 3. Place bracket over holes and attach to unit with two screws removed in step 2 using a T-25 Torx driver. Two units may be installed side-by-side. Tighten screws fully. Cutout width for a side-by-side installation is the 4. Gently push units into position. Be careful not to entangle cutout dimension of a single unit times two. the electrical cord or water line, if applicable. No trim kit is required.
Installation Operation and Maintenance Instructions Water Hookup ! CAUTION PREPARE PLUMBING The water valve uses a standard 1/4" (6.35 mm) Do not use any plastic water supply line. The line is under compression fitting. pressure at all times. Plastic may crack or rupture with age and cause damage to your home. ! CAUTION Do not use tape or joint compound when attaching a braided flexible water supply line that includes a rubber Plumbing installation must observe all state and local gasket.
Installation Operation and Maintenance Instructions Anti-Tip Bracket 3. Locate water valve inlet. 1. Slide unit out so screws on top of unit are easily accessible. 2. Remove the two screws from the opposite side of the hinge assembly using a T-25 Torx driver (see below). 4. Break away filler feature in bushing with flat screwdriver. 3. Place bracket over holes and attach to unit with two Remove ZLWK ɠDW screwdriver screws removed in step 2 using a T-25 Torx driver. Tighten screws fully. 5.
Installation Operation and Maintenance Instructions General Installation INSTALLATION 1. Plug in the power/electrical cord. LEVELING INFORMATION 1. Use a level to 2. Gently push the unit into position. Be careful not to kink confirm the unit is the water supply line or entangle the cord. level. Level should be placed along top edge and side edge 3. Re-check the leveling, from front to back and side to side. as shown. Make any necessary adjustments.
Installation Operation and Maintenance Instructions Door Swing Grille Installation REMOVING AND INSTALLING GRILLE ! WARNING Wall Wall 1/4" Min. (6 mm) 2-1/8" Min. (54 mm) Disconnect electric power to the unit before removing the grille. When using the unit, the grille must be installed. Removing the grille 90 Door Swing 1. Disconnect power to the unit. 90 Door Swing 2. Loosen the two screws (1). Units have a zero clearance for the door to open 90°, when 3. Remove grille (2).
Installation Operation and Maintenance Instructions Door Adjust 5. Tighten bottom hinge screws. HINGE COVER 6. Tighten top hinge screws and replace hinge cover. Hinge cover included with black and stainless models is Location of the unit may make it desirable to mount the door optional. on the opposite side of the cabinet. To install hinge cover: The hinge hardware will be removed and reinstalled on the Press hinge cover squarely over hinge opposite side of the cabinet.
Installation Operation and Maintenance Instructions Install top hinge and door: 1. Install the top hinge. Do not tighten. 5. 2. Rotate door 180° to reverse and set the door onto the bottom hinge. Remove door by tilting forward and lifting door off bottom hinge. Retain shoulder washers; they will be 3. Align edge of the hinge with the outer edge of the unit. reused. 6. 4. Tighten three screws and replace hinge cover. Remove three screws from hinge holes on the opposite side.
Installation Operation and Maintenance Instructions First Use NOTICE All controls are preset at the factory. Initial startup If not intending to use the ice maker, turn the water supply valve off. It is also important to raise the bin arm requires no adjustments. of the ice maker (see above). Failure to raise the bin arm may result in damage to the water valve. NOTICE Marvel recommends discarding the ice produced Certain sounds are normal during the unit’s operation.
Installation Operation and Maintenance Instructions 3. Turn the adjusting screw toward the minus (-) sign ICE MAKER ADJUSTMENT (clockwise) for smaller cubes or toward the plus (+) sign Ice Cube Thickness Adjustment (counterclockwise) for larger cubes. Interval - As Required On ice maker equipped models, adjust the cube size by 4. Install the ice maker assembly cover. changing water amount injected into the ice maker assembly as follows: ADJUSTING ICE HARVEST 1.
Installation Operation and Maintenance Instructions Cleaning If any surface discoloring or rusting appears, clean it quickly EXTERIOR CLEANING nonabrasive cloth. Always clean with the grain. Always finish with Bon-Ami® or Barkeepers Friend Cleanser® and a with Claire® Stainless Steel Polish and Cleaner or Stainless door panels, handles and frames can discolor when comparable product to prevent further problems. exposed to chlorine gas, pool chemicals, saltwater or cleaners with bleach.
Installation Operation and Maintenance Instructions DEFROSTING NOTICE Manual Defrost Models DO NOT clean ice bucket using a dishwasher. The bucket This unit is a manual defrost model and will require is not dishwasher safe and will be damaged. occasional defrosting. When there is build-up of 1/4" (6 mm) or more of frost, manually defrost the unit. 10.When the interior is dry, reconnect power and turn unit on.
Installation Operation and Maintenance Instructions Cleaning Condenser Condenser INTERVAL - EVERY SIX MONTHS To maintain operational efficiency, keep the front grille free of dust and lint, and clean the condenser when necessary. Depending on environmental conditions, more or less frequent cleaning may be necessary. ! WARNING Disconnect electric power to the unit before cleaning the condenser. NOTICE DO NOT use any type of cleaner on the condenser unit. 1. Remove the grille. (See GRILLE INSTALLATION).
Installation Operation and Maintenance Instructions Extended Non-Use VACATION/HOLIDAY, PROLONGED SHUTDOWN For questions regarding extended non-use, please The following steps are recommended for periods of call Marvel at 800.223.3900. extended non-use or if the unit will be exposed to temperatures of 40°F (5°C) or less: ! CAUTION 1. Remove all consumable content from the unit. Damage caused by freezing temperatures is not covered by the warranty. 2.
Installation Operation and Maintenance Instructions Troubleshooting • Evaporator: Refrigerant flowing through an evaporator may sound like boiling liquid. BEFORE CALLING FOR SERVICE If you think your product is malfunctioning, read the • Condenser Fan: Air moving through a condenser may be CONTROL OPERATION section to clearly understand the heard. function of the control.
Installation Operation and Maintenance Instructions Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.
Obtaining Service If Service is Required: • If the product is within the first year warranty period please contact your dealer or call Marvel Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, Marvel Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www.marvelrefrigeration.com under the service and support section.
www.marvelrefrigeration.com 1260 E. VanDeinse St. Greenville, MI 48838 800.223.
