GE T TING STARTED QUICK REFERENCE GUIDE M ARVEL UNDERCOUNTER REFRIGERATION MLNP115-IG01A MLNP115-SS01B MSNP115-SS01A T H E O R I G I N A L R E F R I G E R AT I O N E X P E R T S S I N C E 1 8 9 2
CONTENTS Contents: Important Safety Instructions Safety information ...............................................................2 Unpacking Your Appliance ................................................. 3 Installing your appliance ......................................................4 Electrical ..............................................................................5 Cutout and product dimensions ..........................................6 Door adjustments ....................................
UNPACKING YOUR APPLIANCE ! Warranty Registration WARNING It is important you send in your warranty registration card immediately after taking delivery of your appliance or you can register online at www.marvelrefrigeration.com. EXCESSIVE WEIGHT HAZARD Use two or more people to move product. Failure to do so can result in personal injury. The following information will be required when registering your appliance.
INSTALLING YOUR APPLIANCE Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To ensure your product performs to specifications, the recommended installation location temperature range is from 50 to 100°F (10 to 38°C). Cabinet Clearance Ventilation is required from the bottom front of the appliance. Keep this area open and clear of any obstructions.
ELECTRICAL Electrical Connection A grounded 115 volt, 15 amp dedicated circuit is required. This product is factory equipped with a power supply cord that has a three-pronged, grounded plug. It must be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances (see Figure 6). If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to provide the proper power supply.
CUTOUT & PRODUCT DIMENSIONS PREPARE SITE 14 15⁄16” (379 mm) CAUTION ! Your product has been designed for either free-standing or built-in installation. When built-in, your unit does not require additional air space for top, sides, or rear. However, the front grille must NOT be obstructed, and clearance is required for an electrical connection in the rear. FRONT 28” (711 mm) 34” to 35” (863 mm to 889 mm) Figure 8 CAUTION ! Unit can NOT be installed behind a closed cabinet door.
CUTOUT & PRODUCT DIMENSIONS CUTOUT DIMENSIONS - MLNP115 14 15⁄16” (379 mm) Preferred location for electrical outlet is in an adjacent 5⁄8" cabinet.
16-1/2" 16-1/2" 90° Door Swing DOOR ADJUSTMENTS 90° Door Swing Stainless Steel Black, White and Wood Overlay 2175R(F) & 2275WC Models Door Swing Grille Installation REMOVING AND INSTALLING GRILLE Wall Wall 1/4" Min. (6 mm) 2-1/8" Min. (54 mm) WARNING ! WARNING - Disconnect electric power to the unit before removing the grille. When using the unit, the grille must be installed. WARNING ! Figure 17 90° Door Swing WARNING - DO NOT touch the condenser fins.
DOOR ADJUSTMENTS To align and adjust the door - MSNP115 1. Gently pry off hinge cover from top of unit. 2. Loosen (do not remove) top and bottom hinge screws using a Torx T-25 screwdriver. 3. Align door squarely with cabinet. 4. Make sure gasket is firmly in contact with cabinet all the way around the door (no gaps). Figure 20 3. Remove door by tilting forward and lifting door off bottom hinge. Retain shoulder washers; they will be reused. 5. Tighten bottom hinge screws. 6.
DOOR ADJUSTMENTS Door Adjustments - MLNP115 DOOR ALIGNMENT AND ADJUSTMENT Align and adjust the door if it is not level or not sealing properly. If the door is not sealed, the unit may not cool properly, or excessive frost or condensation may form in the interior. NOTE Properly aligned, the door’s gasket should be firmly in contact with the cabinet all the way around the door (no gaps). Carefully examine the door’s gasket to ensure that it is firmly in contact with the cabinet.
DOOR REVERSAL REVERSING THE DOOR Prepare door for reinstallation: 1. Open door. 1. Remove gasket. This will reveal mounting holes for the magnet assembly. 2. Using T-25 Torx bit loosen screw #1 and remove screw #2 on top and bottom hinge. Slide and remove the door from the unit. 2. Remove magnet assembly from door with T-10 TORX driver. Be sure to only remove the two screws holding the assembly to the door. Reinstall on the opposite end of the door. 3.
INSTALLING THE ANTI-TIP DEVICE Anti-Tip Bracket - MSNP115 5. Check to be sure the unit is level from front to back and side to side. Make any necessary adjustments. The unit’s top surface should be approximately 1/8” (3 mm) below the countertop. 6. Secure bracket to adjoining surface. 1. Slide unit out so screws on top of unit are easily accessible. 2. Remove the two screws from the opposite side of the hinge assembly using a T-25 Torx driver (see below). Leveling Information 1.
INTEGRATED PANEL INSTALLATION Panel Installation 9. MLNP115-IS01A ONLY 3/4" (20 mm) panel Using a Phillips screwdriver, place one screw into each of the 6 pilot holes and screw down. Do not overtighten screws. 10. Ensure the screws sit flush against the bottom of the channel. 145/16" (379 mm) width 30" (762 mm) height Figure 33 1. Fully open door. 2. Starting at corner, pull gasket away from door. 3. Continue to pull gasket free from gasket channel. 11. Remove clamps from door. Figure 31 4.
INSTALLING THE DRAIN PLUMBING Drain This model comes equipped with a factory installed drain pump. CONNECT DRAIN LINE ! NOTE The maximum lift for the drain pump is 10 feet. This must be done as close to the rear of the unit as possible. CAUTION Failure to connect water supply or drain line connections properly can result in personal injury and property damage. See below for typical installations requiring a drain pump.
INSTALLING THE WATER SUPPLY Water Hookup PREPARE PLUMBING The water valve uses a standard 1/4” (6.35 mm) compression fitting. ! CAUTION Plumbing installation must observe all state and local codes. All water and drain connections MUST BE made by a licensed/qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. ! CAUTION Turn off water supply and disconnect electrical supply to unit prior to installation.
OPERATION OF ICE MACHINE Ice First Use Initial startup requires no adjustments. When plugged in, the unit will begin operating under the factory default settings. If the unit was turned off during installation, simply press and the unit will immediately switch on. To turn the unit off, press . NOTE Temperature displayed reflects actual temperature inside unit. If the temperature displayed is different than selected, the unit is progressing towards the selected temperature.
USING YOUR ELECTRONIC CONTROL CONTROL FUNCTION GUIDE FUNCTION COMMAND NOTES ON/OFF Press Unit will immediately turn On or OFF. Adjust Ice Density See “Ice” section. Enable Sabbath Mode Press and hold for 5 seconds and release. The oF / oC symbol will flash briefly after 5 seconds. Interior light and display will go dark and remain so until user resets mode - unit continues to operate. Disable Sabbath Mode Press Display and interior light return to normal operation.
CLEANING YOUR ICE MACHINE Cleaning NUGGET ICE MACHINE CLEANING CYCLE This ice machine has an automatic clean alert function. The control will indicate in the display, approximately every six months with normal use, reminding you to clean your unit. When is displayed, ice production will continue. Depending on water conditions, more frequent cleaning may be necessary. Cleaning removes lime scale, other mineral deposits, and sanitizes the machine.
CLEANING YOUR ICE MACHINE Under normal conditions cleaning should be done when the display shows . You may initiate a cleaning cycle at any time by pressing and holding the clean button for 10 seconds. will appear in the display indicating the start of the cleaning process. You may override in the display without cleaning by pressing and holding the up, down, & light button for 10 seconds. will scroll in the display and the cleaning reminder ( ) will be reset for another approximate six month cycle.
CLEANING YOUR ICE MACHINE 7. will appear in the display a. Reinstall shield and close door. b. The machine will circulate water and perform a series of final rinses for approximately 15 minutes. c. The unit will resume making ice - indicated by 3 sof tones and scrolling in the display. d. Discard first 10 minutes of ice production. Cleaning Condenser INTERVAL - EVERY SIX MONTHS To maintain operational efficiency, keep the front grille free of dust and lint, and clean the condenser when necessary.
CARE AND CLEANING Extended Non-Use VACATION/HOLIDAY, PROLONGED SHUTDOWN The following steps are recommended for periods of extended non-use: ! CAUTION Damage caused by freezing temperatures is not covered by the warranty. Do not put anti-freeze in your unit. 1. Remove all consumable content from the unit. 2. Disconnect the power cord from its outlet/socket and leave it disconnected until the unit is returned to service. 3. Turn off the water supply. 4.
OBTAINING SERVICE Installation Operation and Maintenance Instructions If Service is Required: • If the product is within the first year warranty period please contact your dealer or call Marvel Customer Service at 616.754.5601 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, Marvel Customer Service can provide recommendations of service centers in your area.
HOUSEHOLD PRODUCT WARRANTY Marvel Refrigeration (Marvel) Limited Warranty ONE YEAR LIMITED PARTS & LABOR WARRANTY For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.
www.marvelrefrigeration.com Marvel Refrigeration 1260 E. Van Deinse St. Greenville MI 48838 616.754.5601 30668 Rev A 3/3/21 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
