GE T TING STARTED QUICK REFERENCE GUIDE MAR VEL CLEAR ICE MACHINES MACL215-IS01B MACL215-SS01B MACP215-IS01B MACP215-SS01B T H E O R I G I N A L R E F R I G E R AT I O N E X P E R T S S I N C E 1 8 9 2
CONTENTS Contents: Important Safety Instructions Safety Information ...............................................................2 Unpacking Your Appliance ................................................. 3 Electrical ..............................................................................4 Installing Your Appliance ......................................................5 Door Reversal .....................................................................7 Using Your Electronic Control ............
UNPACKING YOUR APPLIANCE ! WARNING ! If the appliance was shipped, handled, or stored in other than an upright position for any period of time, allow the appliance to sit upright for a period of at least 24 hours before plugging in. This will assure oil returns to the compressor. Plugging the appliance in immediately may cause damage to internal parts. EXCESSIVE WEIGHT HAZARD Use two or more people to move product. Failure to do so can result in personal injury.
ELECTRICAL Electrical Connection A grounded 115 volt, 15 amp dedicated circuit is required. This product is factory equipped with a power supply cord that has a three-pronged, grounded plug. It must be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances (see figure below). If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to provide the proper power supply.
INSTALLING YOUR APPLIANCE ! Cabinet Clearance CAUTION appliance. Keep this area open and clear of any obstructions. Adjacent cabinets and counter top can be installed around the appliance as long as the front grille remains unobstructed. Overlay door models with articulated hinges are intended for built-in applications only. appliance to sit upright for a period of at least 24 hours before plugging in. This will assure oil returns to the compressor.
INSTALLING YOUR APPLIANCE Model Minimum Height 33 3 4" MLC**15 MOC**15 Table A MP**15 Maximum Height ! WARNING Electrical Shock Hazard 34 3 4" • Do not use an extension cord with this appliance. They can be hazardous and can degrade product performance. • electrical supply. • Do not remove the grounding prong from the power cord. • Do not use an adapter. • Do not splash or spray water from a hose on the Do not remove ground prong which may result in severe injury or death.
DOOR REVERSAL Door Reversing Instructions 1. Open door. 2. Loosen screw #1 and #2 using a Philips Screwdriver on top and bottom hinge. Slide door and remove the door from the unit. 3. Once door is removed, using a Philips Screwdriver remove screws from magnet actuator located on inside and bottom of door. (On Integrated Models magnet actuator will be located on bottom of door. 4. Remove caps from top of door. Using a Philips Screwdriver, install magnet actuator on opposite side.
USING YOUR ELECTRONIC CONTROL Electronic control Control Function Guide Function Command Notes ON/OFF Press and release. Unit will immediately turn ON or OFF. Enable Sabbath Mode Press and hold for 5 seconds and release. The oF / oC symbol will flash briefly after 5 seconds. Interior light and display will go dark and remain so until user resets mode - unit continues to operate. Disable Sabbath Mode Press and release. Display and interior light return to normal operation.
INSTALLING THE WATER SUPPLY Water Supply ! CAUTION Observe and follow all local building codes when installing this appliance. This ice machine must be connected to a potable cold water supply line. delivering water pressure between a minimum of 20 psi and a maximum of 120 psi. Use 1/4" copper tubing for your water supply which is available at any local hardware or plumbing supply store. Route the 1/4" copper tubing to suit your installation being sure not to kink the tubing.
INSTALLING THE DRAIN PLUMBING ! CAUTION Drain line coiled and secured to the back of the cabinet. Uncoil, route to an appropriate drain and cut to length. This drain pump is designed to be installed in Marvel ice machines only and approved for use with water only. ! WARNING Electrical Shock Hazard Risk of electrical shock or personal injury could occur due to moving components, if the machine compartment access cover is removed before unplugging the ice machine power cord. Drain pump vent tube.
ICE MAKER OPERATION The Ice Making Process fractional freezing to form a slab of ice that is clear and has less dissolved solids than the water it is produced from. This is accomplished by running water over the cold evaporator plate which gradually freezes leaving the dissolved solids in the residual reservoir water to provide clear ice. Water distributor sheet is released and slides onto the grid cutter cutter’s heated wires.
ICE MAKER OPERATION The ice machine will keep producing ice until the ice machine’s bin is full and will restart automatically when ice needs to be replenished in the bin. The ice bin is machine to run for 24-48 hours to accumulate ice in the ice machine’s bin. Ice Production In normal mode the ice machine will produce up to 39 pounds (17.7 kg) of clear ice in a 24-hour period when installed in a 72°F ambient with a 55°F water supply.
CLEANING YOUR ICE MACHINE Clean reminder: CLEAN When cleaning is needed, UI will alternate between "CL" and "ICE" every 3000 cycles to indicate that the unit needs to be cleaned. Over time, mineral buildup on the cold evaporator plate can occur which can adversely affect the quality of your ice. This build-up is dependent on your water source and usage. Normal ice production will continue while the "CLEAN" reminder is displayed.
CARE AND CLEANING Refer to your cleaning solution instructions to determine the proper amount of cleaning solution to add based on evaporator plate. Pour the cleaning the fresh water reservoir. Splash shield brackets Splash shield Lift fascia door up to access evaporator plate Remove all of the ice from the ice bin ICE CLEAN Replace the splash shield if removed. OFF has been removed. If not repeat the clean cycle procedure.
CARE AND CLEANING Front Grille vacuum lint and dirt from the front grille area ! CAUTION SHOCK HAZARD: Disconnect electrical power from the appliance before cleaning with soap and water. Cabinet The painted cabinet can be washed with either a mild soap and water and thoroughly rinsed with clear water. NEVER use abrasive scouring cleaners. Cleaning Routine cleaning of the stainless steel surfaces will serve to greatly extend the life of your product by removing contaminants.
HOUSEHOLD PRODUCT WARRANTY Marvel Refrigeration (Marvel) Limited Warranty ONE YEAR LIMITED PARTS & LABOR WARRANTY For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.
www.marvelrefrigeration.com Marvel Refrigeration 1260 E. Van Deinse St. Greenville MI 48838 616.754.5601 4/30/2022 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
