MARVEL Installation Operation and Maintenance Instructions Combo Ice Machine 6CiM 6OCiM
TABLE OF CONTENTS Unpacking your refrigerator...................................2 Removing the packaging....................................2 Warranty Registration..........................................2 Installing your refrigerator......................................3 Selecting the location.........................................3 Cabinet Clearances............................................3 Outdoor Installation............................................3 Leveling legs.............................
UNPACKING YOUR REFRIGERATOR Remove Packaging Your refrigerator has been packed for shipment with all parts that could be damaged by movement securely fastened. Cut the banding material at the bottom of the carton, unfold the carton at the bottom and remove the carton from the appliance. Remove the plastic bag, styrofoam corner posts and any tape holding the door closed and internal components in place.
INSTALLING YOUR REFRIGERATOR Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To assure your product performs to specifications the recommended installation location temperature range is from 65 to 90°F (18 to 32°C). Cabinet Clearance Ventilation is required from the bottom front section of the unit. Keep this area open and clear of any obstructions.
INSTALLING THE WATER SUPPLY Water Supply Observe and follow all local building codes when installing this appliance. Attach the supplied water line adapter (Figure 4) to the water valve inlet on the back of the refrigerator (See Figure 3). Be sure the rubber washer is in place in the inlet valve nut. Bend the 1/4” copper tubing to suit your installation being sure not to kink the tubing. Use 1/4” copper tubing for your water supply which is available at any local hardware or plumbing supply store.
USING YOUR REFRIGERATOR Setting the temperature control: Initially set the cold control midway between the numbers (between the #3 and #4).After at least 2 hours adjust to the temperature that suits you. The higher the number you select, the cooler the temperature. (See figure 5). After loading the refrigerator allow at least 24 hours for your refrigerator to reach a new temperature setting.
DIMENSIONS FOR MODELS 6CiM & 6OCiM SOLID DOOR 47” (119.38cm) 24-1/16” (61.11cm) 23-7/8” (60.66cm) 34-1/4” to 34-1/2” 87 to 87.6cm) 3” to 3-1/4” 7.62 to 8.26cm) 22” (55.8cm) 26” (66.04cm) Recommended Rough in Opening Dimensions, 6CiM & 6OCiM Solid Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR MODEL 6CiM SOLID OVERLAY DOOR 46-27/32” (119.02cm) 23-7/8” (60.66cm) 24-1/16” (61.11cm) 34-1/4” to 34-1/2” 87 to 87.6cm) 3” to 3-1/4” 7.62 to 8.26cm) 22” (55.8cm) 23-5/16” (59.21cm) Recommended Rough in Opening Dimensions, 6CiM Solid Overlay Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Step 1: Verify door alignment The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side. Use a 5/32” allen wrench for this procedure. (See Figure 7 below). Top hinge pin remove to remove the door.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Step 6: Drill holes in overlay panel Remove the hinge adapter bushings from the top and bottom door hinge adapters. (See Figure 9).Using the holes in the hinge adapters drill 5/16” (8mm) diameter clearance holes into the overlay panels 3/4” (20mm) deep. These will be clearance holes for the top and bottom hinge pins. Step 8: Assemble the lock parts Two (2) lock extensions are supplied with the lock.
CARE AND CLEANING Step 9: Secure overlay panel to the door. With the #8 wood screws provided fasten the overlay panel to the door. (See Figure 12). Step 10: Install lock cam (Models with locks only). Attach the lock cam to the back of the lock assembly with the phillips head machine screw provided. Orient the lock cam vertically when installing on the lock. Step 11: Install door gasket Press the door gasket into the door channel. Make certain the gasket corners are fully inserted.
TROUBLESHOOTING YOUR REFRIGERATOR Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. Some remedies listed in the Troubleshooting Guide are very complex.
TROUBLESHOOTING YOUR REFRIGERATOR Problem Unit too warm or too cold inside. Possible Cause Remedy • Control set too warm or cold • • Excessive usage or prolonged door • openings. Door gasket not sealing properly. • Adjust temperature colder or warmer as required. Allow 24 hours for temperature to stabilize. Adjust temperature control slide as necessary in the refrigerator section of the unit. Airflow must not be obstructed to front grille. See “clearances” on page 3.
DIAGNOSTIC LED AND OBTAINING SERVICE Diagnostic LED In the back of the unit behind the grille there is a diagnostic/status LED. This LED is used to help diagnose any problems with the unit and to tell its status. LED Status Code/Problem Not on or blinking Unit does not have power. Steadily blinking once per second Unit temperature control is in the “OFF” position. Continuously on Unit is “ON” and operating properly. 2 blinks and pause; repeated pattern Defrost thermistor out of range.
HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.
www.marvelrefrigeration.com Northland-Marvel P.O. Box 400 1260 E. Van Deinse St. Greenville MI 48838 800.223.3900 41011768-EN Rev F 11/10/09 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
