Installation Operation and Maintenance Instructions Refrigerator Model 6CARFM
CONTENTS Unpacking your refrigerator................................................... Removing the packaging..................................................... Warranty Registration.......................................................... Installing your refrigerator..................................................... Selecting the location......................................................... Cabinet Clearances.............................................................. Leveling legs............
UNPACKING YOUR REFRIGERATOR Remove Packaging Warranty Registration Your refrigerator has been packed for shipment with all parts that could be damaged by movement securely fastened. Cut the banding material at the bottom of the carton, unfold the carton at the bottom and remove the carton from the appliance. Remove the plastic bag, styrofoam corner posts, and any tape holding the door closed and internal components in place.
INSTALLING YOUR REFRIGERATOR Leveling Legs Select Location Adjustable legs at the front and rear corners of the unit should be set so the unit is firmly positioned on the floor and level from side to side and front to back. The overall height of your Marvel refrigerator may be adjusted from 33-7/8” (86.1cm) with the leveling legs turned in, and up to 34-7/8” (88.6cm) with the leveling legs extended. The proper location will ensure peak performance of your appliance.
GROUNDING METHOD AND ELECTRICAL REQUIREMENTS • • Do not splash or spray water from a hose on the refrigerator! Doing so may cause an electrical shock, which may result in severe injury or death. This unit should not, under any circumstances, be installed to an un-grounded electrical supply. Grounding Method This product is factory equipped with a power supply cord that has a three-pronged, grounded plug.
HANDLE INSTALLATION AND DOOR ALIGNMENT Handle Installation (Solid Door Models) 1. 2. Door Alignment Procedure Remove the handle, (2) screws, and 5/32” allen wrench from the bag shipped inside the cabinet. Locate handle opposite the hinges and secure in place using the (2) screws and the allen wrench. (See Figure 6). The door should be parallel to the sides and top of the refrigerator.
USING YOUR MICROSENTRY™ REFRIGERATOR CONTROL Figure 8 Control Alarm CF Colder Set Warmer Press and Hold Door Switch Refrigerator operation ON/OFF The available temperature range of the refrigerator is 1° to 7° C. It may take up to 24 hours for your refrigerator to reach desired temperature. This will depend on amount of contents loaded and number of openings and closings of the door.
USING YOUR MICROSENTRY™ REFRIGERATOR CONTROL Temperature Sensor Fault: If the controller detects that the temperature sensor is not properly functioning, a temperature sensor alarm will sound. “E1” will flash on the display, and an alarm will sound. Please call AGA MARVEL Customer Service or your dealer if this error code is displayed.
DIMENSIONS FOR MODEL 6CARM SOLID DOOR 47-3/32” (119.61 cm) 24-7/8” (63.20 cm) 25-11/32” (64.36 cm) 24-3/32” (61.19 cm) 23-7/8” (60.66 cm) 33-7/8” to 34-7/8” (86.1 to 88.6 cm) 3” to 4” 7.62 to 10.2cm) 22” (55.88 cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS, MODEL 6CARM SOLID DOOR Electrical Requirements: A grounded 115 volt, 15 amp dedicated circuit is required. Power outlet can be located in the back wall behind unit. Add 1” to depth for thickness of plug, or recess outlet 1” into the wall.
DIMENSIONS FOR MODEL 6CARM GLASS DOOR 46-7/8” (119.08 cm) 25-19/32” (65.0 cm) 26-1/32” (66.12 cm) 24-3/32” (61.19 cm) 23-7/8” (60.66 cm) 33-7/8” to 34-7/8” (86.1 to 88.6 cm) 3” to 4” 7.62 to 10.2cm) 22” (55.88 cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS, MODEL 6CARM GLASS DOOR Electrical Requirements: A grounded 115 volt, 15 amp dedicated circuit is required. Power outlet can be located in the back wall behind unit. Add 1” to depth for thickness of plug, or recess outlet 1” into the wall.
FEATURES Probe Port (optional) 6CARM Features The optional probe port is a hole from the inside to the outside of the unit, which is located on the back of the unit. After inserting your wires or probe, seal the hole tightly with caulk, putty, foam, etc. for proper operation. There are three adjustable cantilever shelves. Shelves can be adjusted up or down to accommodate various content sizes. To Add or Remove a Shelf Remove stored product from the shelf.
ENERGY SAVING TIPS AND CARE AND CLEANING The following suggestions will minimize the cost of operating your refrigeration appliance. Front Grille Periodically brush and vacuum the front grille area to maintain proper air flow through the condenser coil. See page 4, Figure 2. 1. Do not install your appliance next to a hot appliance, (ovens, glassware washers, etc.). heating air duct, or other heat sources. 2. Install product out of direct sunlight. 3.
TROUBLESHOOTING YOUR REFRIGERATOR • Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. However, it may be required to contact your dealer or a qualified service technician.
COMMERCIAL PRODUCT WARRANTY Entire Product - One Year Parts and Labor Warranty AGA MARVEL warrants to the original purchaser that it will supply all necessary parts and labor to repair or replace in the end user’s establishment, any component which is found by an authorized representative of AGA MARVEL to be defective in materials or workmanship, subject to the conditions and exclusions stated below, for a period of one year from the date of purchase by the end user.
APPENDIX A, ADDITIONAL MICROSENTRY™ FEATURES Information Menu / Lockout Key To access the information menu, press the SET key, and immediately release it. In the information menu, a 2 or 3 digit code will be displayed representing each entry in the information menu. The first code displayed will be t1. With each sequential press and release of the SET key, the following codes will appear in this order: t1, thi, tLo, Ahi, ALo, AdL, cnd, and Loc.
www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.3900 41012474-EN Rev B 10/28/11 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
