MARVEL REFRIGERATED BEVERAGE CENTER Installation Operation and Maintenance Instructions Refrigerated Beverage Center 3SBARE, 6SBARE & 8SBARE
UNPACKING YOUR BEVERAGE CENTER Remove Packaging Your refrigerated beverage center has been packed for shipment with all parts that could be damaged by movement securely fastened. Before using, be sure all packing materials and tape have been removed. Important Keep your carton packaging until your beverage center has been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed as proof of damage in transit.
INSTALLING YOUR BEVERAGE CENTER Select Location The proper location will ensure peak performance of your appliance. Choose a location where the unit will be out of direct sunlight and away from heat sources. Best performance will be maintained when installed within the following parameters: Ideal Ambient Temperature Range Built-In 65-80 °F Free-Standing 65-90 °F Cabinet Clearance Ventilation is required from the bottom front section of the unit. Keep this area open and clear of any obstructions.
SENTRY SYSTEM™ REFRIGERATION MONITOR ON OFF 55 F Set Warmer °F/C Colder Light Sentry System™ Power Failure - Flashing Amber High/Low Temp - Red Press ON/OFF - Reset Alarms OFF - Steady Amber Figure 3 Start Your Appliance Your appliance will start upon initial plug-in. The LED will flash amber upon initial plug-in due to your unit being powered-on at the factory to verify performance and then powered-off.
3SBARE BEVERAGE CENTER FEATURES Insert Wine Bottles The wine rack roll-out shelf holds four (4) bottles. See Figure 4 for typical wine bottle orientation. Loading Tips and Suggestions The wine rack can be placed in the position you desire. For red wines, place the wine rack in the upper most position (the warmest) and for white or sparkling wines in the middle to lower position (the coldest). Place the glass shelves as desired on the remaining five (5) choices of rail glides (see Figure 5).
SBARE BEVERAGE CENTER FEATURES Insert Wine Bottles The six (6) roll-out shelves each hold eight (8) bottles. See Figure 7 for typical wine bottle spacing. Tall bottles should not be loaded on the bottom rack because they may prevent the door from closing. Loading Tips and Suggestions Position white wines on the middle or lower racks and red wines on the upper racks (see Figure 8).
8SBARE BEVERAGE CENTER FEATURES Insert Wine Bottles The six (6) roll-out shelves each hold eight (8) bottles. See Figure 10 for typical wine bottle spacing. Tall bottles should not be loaded on the bottom rack because they may prevent the door from closing. Loading Tips and Suggestions Position white wines on the middle or lower racks and red wines on the upper racks (see Figure 11).
CARE AND CLEANING OF YOUR BEVERAGE CENTER Condenser The condenser tubing inside the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over the coils. Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the condenser for efficient performance by unscrewing the grille on the bottom front of the cabinet.
TROUBLESHOOTING YOUR BEVERAGE CENTER Before Calling for Service Before calling for service, check the troubleshooting table on this page. This table lists possible problems that you can remedy without difficulty to avoid an unnecessary service call. PROBLEM Odor in cabinet Noisy operation Cabinet vibrates Cabinet light not working POSSIBLE CAUSES/SOLUTIONS 1. Interior needs cleaning 1. Cabinet not level 2. Weak floor 1. Cabinet not level 2. Weak floor 1. Tube burned out 2. No power at outlet 1.
OBTAINING SERVICE FOR YOUR BEVERAGE CENTER If You Do Need Service If you do need service, contact your dealer or Marvel Industries. In any correspondence, refer to the model number and serial number of your unit which is located on the upper left hand side of the wall liner. Retain your proof of purchase. You may want to record these numbers in the space below.
HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.
www.lifeluxurymarvel.com Marvel Industries P.O. Box 997 Richmond, IN 47375-0997 800.428.6644 An AGA Company 41010407 Rev. C 03.03.08 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
