MARVEL ICE MACHINE Installation Operation and Maintenance Instructions Clear Ice Models 30iM 3OiM outdoor w w w. l i f e l u x u r y m a r v e l . c o m Marvel Industries P.O. Box 997 Richmond, IN 47375-0997 800.428.6644 l i f e . l u x u r y. m a r v e l ™. 41010308 Rev. A All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements additions, replacements or compensation for previously purchased products.
P R E PA R I N G Y O U R I C E M A C H I N E F O R S TO R A G E Storage of Ice Machine If the ice machine is to be moved, not used for an extended time or will be in an area that will be near freezing temperatures – below 37° F, it is necessary to remove the remaining water in the ice-making system. ALL WATER MUST BE DRAINED AND REMOVED TO PREVENT ICE MACHINE DAMAGE AND POSSIBLE WATER DAMAGE TO THE SURROUNDING AREA IN FREEZING CONDITIONS. THESE DAMAGES ARE NOT COVERED UNDER WARRANTY.
S TA RT I N G O U T S E RV I C E PA RT S L I S T F O U R Remove Packaging Your ice machine has been packed for shipment with all parts that could be damaged by movement securely fastened. Before installing the ice machine, be sure all packing materials and tape have been removed. Important Save the carton packaging until your ice machine has been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed as proof of damage sustained in transit.
S E RV I C E PA RT S D I A G R A M F O U R I N S TA L L AT I O N 7 1 6,9 5 Select Location The proper location will ensure peak performance of your ice machine. Choose a location away from heat and out of direct sunlight. Best performance will be maintained when installed within the following parameters: Framed, Panel Ready Style Door 6 9 2 8 Ideal Ambient Temperature Range* built-in 55-80°F freestanding 55-90°F * Ice Machine will not perform correctly in ambient temperatures less than 55°F.
I N S TA L L AT I O N : D R A I N P L U M B I N G S E RV I C E PA RT S L I S T T H R E E Drain Plumbing Your ice machine uses a gravity drain, (figure 1) that requires 5/8" I.D. tubing from the back of the ice machine to a plumbed connection to a sanitary sewer. Remove the access panel to plumb in drain connection. Gravity drain location for built-in units can be within the area shown in figure 3.
S E RV I C E PA RT S D I A G R A M T H R E E WAT E R S U P P LY Water Supply This ice machine must be connected to a potable, active cold water supply line delivering water pressure at a minimum of 20 psi and maximum of 120 psi. 42 V COM 120V V 4000-20C02AE411 PRI-120VAC 20 V.A. SA SEC-12VAC RL 3597G 50/60Hz CLASS 2 "B" 130-G PRODUCTS UNLIMITED CORP, U.S.A. V 12V V * • Water connection is made through a right angle garden hose fitting supplied with ice machine.
CARE OF THE UNIT Care of Unit 1. Avoid leaning on the cabinet door. You may bend the door hinge or tip the unit. 2. Exercise caution when sweeping, vacuuming, or mopping near the front of the unit. Damage to the grille and/or switch can occur. 3. Periodically clean the inside of the ice machine components and inside of unit (see Cleaning Your Ice Machine section). 4. Periodically check and/or clean the front grille and condenser coils as needed. 5.
S E RV I C E PA RT S D I A G R A M T W O 1 CARING FOR YOUR ICE MACHINE 2 7 3 5 Cleaning Your Ice Machine Some impurities will remain and build up in the ice machine and stick to the ice machine's parts over time. This build-up must be removed for proper ice production, ice quality, and ice machine life. Your ice machine is equipped with a cleaning mode that will help in cleaning out these impurities. 7.
T H I N G S TO R E M E M B E R S E RV I C E PA RT S L I S T O N E Illus. No. Things to Remember • Allow your ice machine to run for 24-48 hours to accumulate ice in ice machine's bin. • Keep your ice machine clean for proper ice quality, production, and unit life. • Room and water temperatures will greatly affect the output of ice in your unit (see table). Ice will also melt away, especially at the start of an empty bin, but will slow down as ice accumulates.
S E RV I C E PA RT S D I A G R A M O N E D O O R A LT E R AT I O N S Optional Door Handle Installation for Panel Ready Doors (for units without door handle attached) The door handle for certain doors may be packed inside your ice machine and can be mounted on the top or side of your refrigerator door. Locate the handle where it is convenient for you. You will need a 1/4" hex head driver to install the handle. Place the handle on the outside surface of the door.
TROUBLESHOOTING FOUR O B TA I N I N G S E RV I C E Before Calling for Service Before calling for service, check the following items: • Make sure unit is plugged into outlet. • Check the outlet for power. Test outlet with lamp to make certain outlet has power. • Make sure ice machine's switch is in the "ON" position. • Make sure that there is cold water supplied to the ice machine. • Make sure drain plug on bottom of reservoir is inserted. • Make certain unit is level from front to back and side to side.
TROUBLESHOOTING THREE WA R R A N T Y PROBLEM POSSIBLE CAUSE CORRECTION Ice is not clear. Low water level in reservoir. Make sure that the reservoir drain plug is installed properly. Check the water line to the unit to make sure there are no restrictions or kinks in the line. Check all filters to make sure they are not restricted or plugged. Make certain that water line is not connected to the water softener. Move the unit to an area where room temperature is above 55° F. Softened water supply.
TROUBLESHOOTING ONE PROBLEM POSSIBLE CAUSE CORRECTION PROBLEM POSSIBLE CAUSE CORRECTION Unit does not operate. The unit is unplugged. Breaker is tripped or fuse is blown. Plug in the unit. Reset breaker or replace fuse. Check to make sure there is not a short in the electrical circuit. Set the rocker switch on the grille of the ice machine to the "ON" position. Ice cubes are too small (less than 1/2 inch thick). Low ice consumption.
TROUBLESHOOTING ONE PROBLEM POSSIBLE CAUSE CORRECTION PROBLEM POSSIBLE CAUSE CORRECTION Unit does not operate. The unit is unplugged. Breaker is tripped or fuse is blown. Plug in the unit. Reset breaker or replace fuse. Check to make sure there is not a short in the electrical circuit. Set the rocker switch on the grille of the ice machine to the "ON" position. Ice cubes are too small (less than 1/2 inch thick). Low ice consumption.
TROUBLESHOOTING THREE WA R R A N T Y PROBLEM POSSIBLE CAUSE CORRECTION Ice is not clear. Low water level in reservoir. Make sure that the reservoir drain plug is installed properly. Check the water line to the unit to make sure there are no restrictions or kinks in the line. Check all filters to make sure they are not restricted or plugged. Make certain that water line is not connected to the water softener. Move the unit to an area where room temperature is above 55° F. Softened water supply.
TROUBLESHOOTING FOUR O B TA I N I N G S E RV I C E Before Calling for Service Before calling for service, check the following items: • Make sure unit is plugged into outlet. • Check the outlet for power. Test outlet with lamp to make certain outlet has power. • Make sure ice machine's switch is in the "ON" position. • Make sure that there is cold water supplied to the ice machine. • Make sure drain plug on bottom of reservoir is inserted. • Make certain unit is level from front to back and side to side.
S E RV I C E PA RT S D I A G R A M O N E D O O R A LT E R AT I O N S Optional Door Handle Installation for Panel Ready Doors (for units without door handle attached) The door handle for certain doors may be packed inside your ice machine and can be mounted on the top or side of your refrigerator door. Locate the handle where it is convenient for you. You will need a 1/4" hex head driver to install the handle. Place the handle on the outside surface of the door.
T H I N G S TO R E M E M B E R S E RV I C E PA RT S L I S T O N E Illus. No. Things to Remember • Allow your ice machine to run for 24-48 hours to accumulate ice in ice machine's bin. • Keep your ice machine clean for proper ice quality, production, and unit life. • Room and water temperatures will greatly affect the output of ice in your unit (see table). Ice will also melt away, especially at the start of an empty bin, but will slow down as ice accumulates.
S E RV I C E PA RT S D I A G R A M T W O 1 CARING FOR YOUR ICE MACHINE 2 7 3 5 Cleaning Your Ice Machine Some impurities will remain and build up in the ice machine and stick to the ice machine's parts over time. This build-up must be removed for proper ice production, ice quality, and ice machine life. Your ice machine is equipped with a cleaning mode that will help in cleaning out these impurities. 7.
CARE OF THE UNIT Care of Unit 1. Avoid leaning on the cabinet door. You may bend the door hinge or tip the unit. 2. Exercise caution when sweeping, vacuuming, or mopping near the front of the unit. Damage to the grille and/or switch can occur. 3. Periodically clean the inside of the ice machine components and inside of unit (see Cleaning Your Ice Machine section). 4. Periodically check and/or clean the front grille and condenser coils as needed. 5.
S E RV I C E PA RT S D I A G R A M T H R E E WAT E R S U P P LY Water Supply This ice machine must be connected to a potable, active cold water supply line delivering water pressure at a minimum of 20 psi and maximum of 120 psi. 42 V COM 120V V 4000-20C02AE411 PRI-120VAC 20 V.A. SA SEC-12VAC RL 3597G 50/60Hz CLASS 2 "B" 130-G PRODUCTS UNLIMITED CORP, U.S.A. V 12V V * • Water connection is made through a right angle garden hose fitting supplied with ice machine.
I N S TA L L AT I O N : D R A I N P L U M B I N G S E RV I C E PA RT S L I S T T H R E E Drain Plumbing Your ice machine uses a gravity drain, (figure 1) that requires 5/8" I.D. tubing from the back of the ice machine to a plumbed connection to a sanitary sewer. Remove the access panel to plumb in drain connection. Gravity drain location for built-in units can be within the area shown in figure 3.
S E RV I C E PA RT S D I A G R A M F O U R I N S TA L L AT I O N 7 1 6,9 5 Select Location The proper location will ensure peak performance of your ice machine. Choose a location away from heat and out of direct sunlight. Best performance will be maintained when installed within the following parameters: Framed, Panel Ready Style Door 6 9 2 8 Ideal Ambient Temperature Range* built-in 55-80°F freestanding 55-90°F * Ice Machine will not perform correctly in ambient temperatures less than 55°F.
S TA RT I N G O U T S E RV I C E PA RT S L I S T F O U R Remove Packaging Your ice machine has been packed for shipment with all parts that could be damaged by movement securely fastened. Before installing the ice machine, be sure all packing materials and tape have been removed. Important Save the carton packaging until your ice machine has been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed as proof of damage sustained in transit.
P R E PA R I N G Y O U R I C E M A C H I N E F O R S TO R A G E Storage of Ice Machine If the ice machine is to be moved, not used for an extended time or will be in an area that will be near freezing temperatures – below 37° F, it is necessary to remove the remaining water in the ice-making system. ALL WATER MUST BE DRAINED AND REMOVED TO PREVENT ICE MACHINE DAMAGE AND POSSIBLE WATER DAMAGE TO THE SURROUNDING AREA IN FREEZING CONDITIONS. THESE DAMAGES ARE NOT COVERED UNDER WARRANTY.
NOTES
MARVEL ICE MACHINE Installation Operation and Maintenance Instructions Clear Ice Models 30iM 3OiM outdoor w w w. l i f e l u x u r y m a r v e l . c o m Marvel Industries P.O. Box 997 Richmond, IN 47375-0997 800.428.6644 l i f e . l u x u r y. m a r v e l ™. 41010308 Rev. A All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements additions, replacements or compensation for previously purchased products.
