MARVEL Installation Operation and Maintenance Instructions Ice Machines 15iM 25iM
TABLE OF CONTENTS Unpacking your ice machine..................................2 Removing the packaging....................................2 Warranty Registration..........................................2 Installing your ice machine.....................................3 Selecting the location.........................................3 Cabinet Clearances............................................3 Leveling legs......................................................3 Grounding method...........................
UNPACKING YOUR ICE MACHINE Remove Packaging Your ice machine has been packed for shipment with all parts that could be damaged by movement securely fastened. Cut the banding material at the bottom of the carton, unfold the carton at the bottom and remove the carton from the appliance. Remove the plastic bag, styrofoam corner posts and any tape holding the door closed and internal components in place.
INSTALLING YOUR ICE MACHINE Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To assure your product performs to specifications the recommended installation location temperature range is from 65 to 90°F (18 to 32°C). Cabinet Clearance Ventilation is required from the bottom front section of the unit. Keep this area open and clear of any obstructions.
INSTALLING THE WATER SUPPLY Water Supply Observe and follow all local building codes when installing this appliance. Attach the supplied water line adapter (Figure 4) to the water valve inlet on the back of the ice machine (See Figure 3). Be sure the rubber washer is in place in the inlet valve nut. Bend the 1/4” copper tubing to suit your installation being sure not to kink the tubing. Use 1/4” copper tubing for your water supply which is available at any local hardware or plumbing supply store.
USING YOUR ICE MACHINE Turning on the ice machine After connecting the water supply, and setting your ice machine in place plug the power cord into the wall receptacle. Then place the switch located in the grille (see Figure 5) to the “ON” position. The temperature control is factory preset, allow the ice maker to run for 24 hours so the interior temperature will stabilize.
DIMENSIONS FOR MODEL 15iM SOLID DOOR 35-5/8” (90.47cm) 16-13/16” (42.7cm) 23-11/16” (60.17cm) 14-7/8” (37.8cm) 24-1/8” to 24-13/16” (61.26 to 63.02cm) 3-15/16” to 4-5/8” (10.01 to 25.43cm) 19-23/32” (50.09cm) 21-25/32” (55.32cm) Recommended Rough in Opening Dimensions,15iM Solid Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 24-1/2” (62.23cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR MODEL 25iM SOLID DOOR 35-21/32” (90.55cm) 16-9/16” (42.06cm) 23-11/16” (60.17cm) 14-7/8” (37.8cm) 21-25/32” (55.32cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) 19-23/32” (50.09cm) Recommended Rough in Opening Dimensions, 25iM Solid Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR MODEL 25iM SOLID OVERLAY DOOR 35-21/32” (90.55cm) 21-25/32” (55.32cm) 14-7/8” (37.8cm) 21-1/32” (53.42cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) 19-23/32” (50.09cm) Recommended Rough in Opening Dimensions, 25iM Solid Overlay Door Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.6 cm) Power outlet can be located in the back wall behind unit.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Step 1: Verify door alignment The door should be parallel to the sides and top of the ice machine. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side. Use a 5/32” allen wrench for this procedure. (See Figure 7 below). Top hinge pin remove to remove the door.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Step 6: Drill holes in overlay panel Remove the hinge adapter bushings from the top and bottom door hinge adapters. (See Figure 9).Using the holes in the hinge adapters drill 5/16” (8mm) diameter clearance holes into the overlay panels 3/4” (20mm) deep. These will be clearance holes for the top and bottom hinge pins. Step 8: Assemble the lock parts Two (2) lock extensions are supplied with the lock.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS Step 9: Secure overlay panel to the door. With the #8 wood screws provided fasten the overlay panel to the door. (See Figure 12). Step 10: Install lock cam (Models with locks only). Attach the lock cam to the back of the lock assembly with the phillips head machine screw provided. Orient the lock cam vertically when installing on the lock. Step 11: Install door gasket Press the door gasket into the door channel.
CARE AND CLEANING Condenser Air Flow The machine compartment located beneath the cabinet does not require frequent cleaning; however, satisfactory performance depends on adequate ventilation. Be sure nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille openings. See Figure 1 on page 3. Cabinet The painted cabinet can be washed with either a mild soap and water and thoroughly rinsed with clear water.
TROUBLESHOOTING YOUR ICE MACHINE Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshoot- Electrocution Hazard - Never attempt to repair or perform ing guide below. Locate the problem in the guide and refer maintenance on the unit until the main electrical power has to the cause and its remedy before calling for service. The been disconnected.
TROUBLESHOOTING YOUR ICE MACHINE Problem Unit too warm or too cold inside. Possible Cause Remedy • Control set too warm or cold • • Airflow to front grille blocked. • • • Excessive usage or prolonged door • openings. Door gasket not sealing properly. • • Unit not level • • Water line tubing vibration. • • Unit turned off • • • Power cord not plugged in. No power at outlet. • • Moisture collects on outside surface of cabinet. • Hot and humid conditions.
OBTAINING SERVICE If Service is Required: • If the product is within the first year warranty period please call Marvel Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, Marvel Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www. marvelrefrigeration.com under the service and support section.
HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user.
NOTES 17
NOTES 18
www.marvelrefrigeration.com Northland-Marvel P.O. Box 400 1260 E. Van Deinse St. Greenville MI 48838 800.223.3900 41011771-EN Rev D 11/10/09 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
