Installation Operation and Maintenance Instructions Ice Machines 15CM 25CM Freezer 15CAF
CONTENTS Unpacking your ice machine or freezer ................................ Removing the packaging..................................................... Warranty Registration.......................................................... Installing your ice machine or freezer .................................. Selecting the location......................................................... Cabinet Clearances.............................................................. Leveling legs............................
UNPACKING YOUR ICE MACHINE OR FREEZER Warranty Registration Remove Packaging It is important you send in your warranty registration card immediately after taking delivery of your ice machine or you can register online at www.agamarvel.com. Your ice machine has been packed for shipment with all parts that could be damaged by movement securely fastened. Cut the banding material at the bottom of the carton, unfold the carton at the bottom, and remove the carton from the appliance.
INSTALLING YOUR ICE MACHINE OR FREEZER Select Location Leveling Legs The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To assure your product performs to specifications the recommended installation location temperature range is from 65 to 90°F (18 to 32°C).
HANDLE INSTALLATION Handle Installation (Solid Door Models) 1. 2. • • Do not splash or spray water from a hose on the ice machine! Doing so may cause an electrical shock, which may result in severe injury or death. This unit should not, under any circumstances, be installed to an un-grounded electrical supply. Remove the handle, (2) screws, and 5/32” allen wrench from the bag shipped inside the cabinet. Locate handle opposite the hinges and secure in place using the (2) screws and the allen wrench.
DOOR ALIGNMENT Door Alignment Procedure The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets on the top and bottom of the door and adjusting the door side to side. Use a 5/32” allen wrench for this procedure. (See Figure 5 below). When finished aligning the door, tighten the screws securely.
INSTALLING THE ICE MACHINE WATER SUPPLY Water Supply NOTE Observe and follow all local building codes when installing this appliance. Attach the supplied water line adapter (Figure 7) to the water valve inlet on the back of the ice machine (See Figure 6). Be sure the rubber washer is in place in the inlet valve nut. Bend the 1/4” copper tubing to suit your installation being sure not to kink the tubing.
USING YOUR ICE MACHINE Turning on the ice machine Ice maker operation After connecting the water supply, and setting your ice machine in place plug the power cord into the wall receptacle. Then place the switch located in the grille (see Figure 8) to the “ON” position. The temperature control is factory preset, allow the ice maker to run for 24 hours so the interior temperature will stabilize.
USING YOUR FREEZER Turning on the freezer After setting the freezer in place, leveling (see page 4), plug the power cord into the wall receptacle. The freezer should start after plugging in. The temperature control is factory preset to a mid range setting. Allow the freezer to run for 24 hours so the interior temperature stabilizes. If you wish to adjust the interior temperature use a small bladed screwdriver pushed through the right hand side of the grille to turn the temperature control shaft.
DIMENSIONS FOR MODEL 15CM SOLID DOOR 35-11/16” (90.65cm) 15-7/8” (40.34cm) 23-1/32” (58.5cm) 14-7/8” (37.8cm) 24-1/8” to 25-18” (61.26 to 63.82cm) 3-15/16” to 4-15/16” (10.01 to 12.54cm) 19-11/16” (50.01cm) 21-25/32” (55.32cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS,15CM SOLID DOOR Electrical Requirements: A 115 volt, 15 amp dedicated circuit is required. A 3 prong grounded receptacle is required. Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR MODEL 25CM SOLID DOOR 35-9/16” (90.32cm) 15-7/8” (40.34cm) 23-1/32” (58.5cm) 14-7/8” (37.8cm) 21-25/32” (55.32cm) 33-3/4” to 34-3/4” (85.7 to 88.3cm) 3” to 4” (7.62 to 10.2cm) 19-11/16” (50.09cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS, 25CM SOLID DOOR Electrical Requirements: A 115 volt, 15 amp dedicated circuit is required. A 3 prong grounded receptacle is required. Power outlet can be located in the back wall behind unit.
DIMENSIONS FOR MODEL 15CAF SOLID DOOR 35-11/16” (90.32cm) 15-7/8” (40.34cm) 23-1/32” (58.5cm) 14-7/8” (37.8cm) 24-1/8” to 25-1/8” (61.26 to 63.82cm) 19-11/16” (50.01cm) 3-15/16” to 4-15/16” (10.01 to 12.54cm) 21-25/32” (55.32cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS, 15CAF SOLID DOOR Electrical Requirements: A 115 volt, 15 amp dedicated circuit isrequired. A 3 prong grounded receptacle is required. Power outlet can be located in the back wall behind unit.
FEATURES AND ENERGY SAVING TIPS 15CAF Features Can be installed on the counter top or built in. Temperature range = -4°C to -20°C. Flat door liner. Manual defrost. 15CM Features Can be installed on the counter top or built in. Makes crescent shaped ice cubes. Temperature range = -7° to -20°C. Flat door liner. Manual defrost No drain required. 25CM Features Makes crescent shaped ice cubes. Temperature range = -7° to -20°C. Flat door liner. Manual defrost No drain required.
CARE AND CLEANING Condenser Air Flow The condenser underneath the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over this heat exchanger. It is recommended to annually clean the condenser by vacuuming and brushing. To access the condenser, the unit must be pulled out from the installation, and the lower machine compartment access cover removed. Defrosting Instructions 15CM and 25CM 1. 2. 3.
TROUBLESHOOTING YOUR ICE MACHINE Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. However, it may be required to contact your dealer or a qualified service technician.
TROUBLESHOOTING YOUR ICE MACHINE OR FREEZER Problem Unit too warm or too cold inside. Possible Cause Remedy • Control set too warm or cold. • • Airflow to front grille blocked. • • • • Excessive usage or prolonged door openings. Door gasket not sealing properly. • Unit not level. • • Water line tubing vibration. • Unit will not run. • • • Unit turned off. Power cord not plugged in. No power at outlet. • • • Turn unit on. See page 8 or 9. Plug in power cord. Check house circuit.
OBTAINING SERVICE If Service is Required: • • • • • If the product is within the first year warranty period please contact your dealer or call AGA MARVEL Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. If the product is outside the first year warranty period, AGA MARVEL Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www.agamarvel.
COMMERCIAL PRODUCT WARRANTY Entire Product - One Year Parts and Labor Warranty AGA MARVEL warrants to the original purchaser that it will supply all necessary parts and labor to repair or replace in the end user’s establishment, any component which is found by an authorized representative of AGA MARVEL to be defective in materials or workmanship, subject to the conditions and exclusions stated below, for a period of one year from the date of purchase by the end user.
NOTES 19
www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.3900 41011870-EN Rev J 4/23/12 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
