Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment • FAST SHIPPING AND DELIVERY • TENS OF THOUSANDS OF IN-STOCK ITEMS • EQUIPMENT DEMOS • HUNDREDS OF MANUFACTURERS SUPPORTED • LEASING/MONTHLY RENTALS • ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-back
Installation Operation and Maintenance Instructions Ice Machines 15CM 25CM Freezer 15AF Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
CONTENTS Unpacking your ice machine or freezer ................................ Removing the packaging..................................................... Warranty Registration.......................................................... Installing your ice machine or freezer .................................. Selecting the location......................................................... Cabinet Clearances.............................................................. Leveling legs............................
UNPACKING YOUR ICE MACHINE OR FREEZER Remove Packaging Your ice machine has been packed for shipment with all parts that could be damaged by movement securely fastened. Cut the banding material at the bottom of the carton, unfold the carton at the bottom, and remove the carton from the appliance. Remove the plastic bag, styrofoam corner posts, and any tape holding the door closed and internal components in place.
INSTALLING YOUR ICE MACHINE OR FREEZER Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To assure your product performs to specifications the recommended installation location temperature range is from 65 to 90°F (18 to 32°C). Cabinet Clearance Ventilation is required from the bottom front section of the unit. Keep this area open and clear of any obstructions.
HANDLE INSTALLATION Handle Installation (Solid Door Models) 1. Remove the handle, (2) screws, and 5/32” allen wrench from the bag shipped inside the cabinet. 2. Locate handle opposite the hinges and secure in place using the (2) screws and the allen wrench. (See Figure 3). Screws Handle Door Reversal It is possible to reverse the door (change from right hand swing to left hand swing or vice versa) if you wish. To do so it will be necessary to order one of the service kits below.
DOOR ALIGNMENT Door Alignment Procedure The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side. Use a 5/32” allen wrench for this procedure. (See Figure 4 below). Top hinge pin remove to remove the door. Hinge adapter screws loosen these to adjust door, on the top and bottom of the door 9/32” (7.
INSTALLING THE ICE MACHINE WATER SUPPLY Water Supply NOTE Observe and follow all local building codes when installing this appliance. Attach the supplied water line adapter (Figure 6) to the water valve inlet on the back of the ice machine (See Figure 5). Be sure the rubber washer is in place in the inlet valve nut. Bend the 1/4” copper tubing to suit your installation being sure not to kink the tubing.
USING YOUR ICE MACHINE Turning on the ice machine After connecting the water supply, and setting your ice machine in place plug the power cord into the wall receptacle. Then place the switch located in the grille (see Figure 7) to the “ON” position. The temperature control is factory preset, allow the ice maker to run for 24 hours so the interior temperature will stabilize.
USING YOUR FREEZER Turning on the freezer After setting the freezer in place, leveling (see page 3), plug the power cord into the wall receptacle. The freezer should start after plugging in. The temperature control is factory preset to a mid range setting. Allow the freezer to run for 24 hours so the interior temperature stabilizes. If you wish to adjust the interior temperature use a small bladed screwdriver pushed through the right hand side of the grille to turn the temperature control shaft.
DIMENSIONS FOR MODEL 15CM SOLID DOOR 35-11/16” (90.65cm) 15-7/8” (40.34cm) 23-1/32” (58.5cm) 14-7/8” (37.8cm) 24-1/8” to 24-13/16” (61.26 to 63.02cm) 3-15/16” to 4-5/8” (10.01 to 25.43cm) 19-11/16” (50.01cm) 21-25/32” (55.32cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS,15CM SOLID DOOR Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 24-5/8” (62.
DIMENSIONS FOR MODEL 25CM SOLID DOOR 35-9/16” (90.32cm) 15-7/8” (40.34cm) 23-1/32” (58.5cm) 14-7/8” (37.8cm) 21-25/32” (55.32cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) 19-11/16” (50.09cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS, 25CM SOLID DOOR Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 34-1/2” (87.
DIMENSIONS FOR MODEL 15AF SOLID DOOR 35-11/16” (90.32cm) 15-7/8” (40.34cm) 23-1/32” (58.5cm) 14-7/8” (37.8cm) 24-1/8” to 24-13/16” (61.26 to 63.02cm) 3-15/16” to 4-5/8” (10.01 to 25.43cm) 19-11/16” (50.01cm) 21-25/32” (55.32cm) RECOMMENDED ROUGH IN OPENING DIMENSIONS, 15AF SOLID DOOR Electrical Requirements: 115 volts, 3.3 amps running max. 15 amp dedicated circuit required. 3 prong grounded receptacle required. 24-5/8” (62.
FEATURES 15AF Features Can be installed on the counter top or built in. Temperature range = -4°C to -20°C. Flat door liner. Manual defrost. Probe Port (optional) for 15AF The optional probe port is a hole from the inside to the outside of the unit, which could be located on the top, side, or back of the unit. After inserting your wires or probe, seal the hole tightly with caulk, putty, foam, etc. for proper operation. 15CM Features Can be installed on the counter top or built in.
CARE AND CLEANING Condenser Air Flow The machine compartment located beneath the cabinet does not require frequent cleaning; however, satisfactory performance depends on adequate ventilation. Be sure nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille openings. See Figure 1 on page 3. Cabinet The painted cabinet can be washed with either a mild soap and water and thoroughly rinsed with clear water.
TROUBLESHOOTING YOUR ICE MACHINE Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. Some remedies listed in the troubleshooting guide are very complex.
TROUBLESHOOTING YOUR ICE MACHINE OR FREEZER Problem Unit too warm or too cold inside. Possible Cause Remedy • Control set too warm or cold. • • Airflow to front grille blocked. • • • • Excessive usage or prolonged door openings. Door gasket not sealing properly. • Unit not level. • • Water line tubing vibration. • Unit will not run. • • • Unit turned off. Power cord not plugged in. No power at outlet. • • • Turn unit on. See page 7 or 8. Plug in power cord. Check house circuit.
OBTAINING SERVICE If Service is Required: • If the product is within the first year warranty period please call AGA MARVEL Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, AGA MARVEL Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www.marvelscientific.com under the service and support section.
COMMERCIAL PRODUCT WARRANTY Entire Product - One Year Parts and Labor Warranty AGA MARVEL warrants to the original purchaser that it will supply all necessary parts and labor to repair or replace in the end user’s establishment, any component which is found by an authorized representative of AGA MARVEL to be defective in materials or workmanship, subject to the conditions and exclusions stated below, for a period of one year from the date of purchase by the end user.
NOTES 18 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
www.marvelscientific.com P.O. Box 400 1260 E. VanDeinse St. Greenville MI 48838-0400 800.223.3900 41011870-EN Rev A 12.22.09 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products. Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment • FAST SHIPPING AND DELIVERY • TENS OF THOUSANDS OF IN-STOCK ITEMS • EQUIPMENT DEMOS • HUNDREDS OF MANUFACTURERS SUPPORTED • LEASING/MONTHLY RENTALS • ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-back
