Marvel Instruction Manual High Definition Personal Video Recorder Digital Satellite Receiver The Sezam Marvel digital receiver is fully compliant with the international Digital Video Broad-casting (DVB) standard, and thus is able to receive digital broadcasts of that standard.
1. Contents Contents 1 2 3 Introduction .......................................................................................................................... 5 1.1 Main Features ............................................................................................................ 5 1.2 Product Descriptions ................................................................................................... 6 1.3 Remote Controller ..........................................................
Safety Instructions ii Safety Precautions This product has been manufactured to act in accordance with the international safety standards. Please read through the safety instructions carefully before using this product as the manufacturer takes no responsibility for any damages due to the consumer’s misuse of the product. 1. Power Supply • Use this product with the type of power supply that is indicated on the marking label. Its operating range is AC 90V~250V and 50/60Hz.
iii Safety Instructions 2. Exposure and Placement • Only operate the product in moderate temperatures. • Place the product indoors to avoid exposing it to lightening, rain or direct sunlight. • Do not expose any liquids or sources of open flame (such as candle flame) to the product. • Do not place the product near any heat emitting appliances. This may cause impairment in cooling.
Safety Instructions iv 4. Warnings • Do not use this product near any flammable or explosive gases as this increases the risk of explosions. • • Do not use the product if any liquids or foreign objects come in contact with it. o Turn the product off, disconnect the power cord, and contact your dealer. o Do not use the product since this could cause a fire or electric shock. Do not operate this product or hold the power cord with wet hands as the risk of getting electronic shock is very high.
5. Introduction Chapter1. Introduction The Sezam Marvel digital receiver is fully compliant with the international Digital Video Broadcasting (DVB) standard, and thus is able to receive digital broadcasts of that standard. For its operation you need an antenna, which must be installed appropriately. 1.1 Main Features ● 1.3GHz Dual threaded MIPS Processor ● 1 e-SATA support ● Linux Operating System ● Support of internal SATA HDD ● Media Player ● 2 x USB 2.0 Rear, 1 x USB 2.
Chapter1. Introduction 1.2 Product Descriptions Front Panel ① Smartcard reader slot ② CI Module slot ③ USB: Connect a USB storage device ④ Display :256 x 64 OLEDDisplays ⑤ CH ▼ : Switches channel ⑥ CH▲ : Switches channel ⑦ Power : Power On 6.
7. Introduction Rear Panel ① On/Off Switch : Power on/off ② Power plug : Connect power cable ③ FAN : Ventilator ④ RS-232 : RS-232 data port is provided ⑤ USB : Connects the USB memory stick or external HDD ⑥ Ethernet : Connects the PC or another set top box of ET.
Chapter1. Introduction 1.3 Remote Controller TV/STB : Puts the Remote in TV or STB mode. (Reserved TV Mode) : Press to go into Standby / Standby options. 0 - 9 : Used for entering channel number and text. PREV : Go to Previous Channel in History. NEXT : Go to Next Channel in History. EPG : Shows the EPG for all / current channel. FAV : Show the Favorite Lists available. MENU : Go to Main Menu / Menu for current function. EXIT : Exit current Menu or Window. OK : Confirms the option.
9. Introduction 1.4 Conditional Access Amongst the channels that are scanned via Sezam Marvel, some channels can be properly tuned in only with the corresponding Smartcard. Sezam Marvel provides two Smartcard Reader slots and users need to purchase those Smartcards that are required for viewing such subscription based services. Insertion of Smartcard ① Open the door on the right side. ② Insert Smartcard as in the following instruction. ③ Make sure that the Smartcard remain inserted while viewing.
Chapter1. Introduction 1.5 Technical Specifications Front Panel Display: 256 x 64 OLED display (Displaying channel names, icons and program information) Smartcard Reader Slot: 2 Common Interface: 2 USB: 1 x USB 2.
11. Introduction RF RF range: 950~2,150 MHz (for DVB-S) 104~862 MHz (for DVB-T2/C) Modulation, FEC, de-multiplexer: DVB-S/DVB-S2/DVB-T2/DVB-C standard Video resolution: 1920x1080 interlaced, progressive Video 1080p@60,1080i and other size Video decoding: H.264, MPEG-2, MPEG-4 compatible Input data rate: 2~45 MSymb/s S/N: > 53 dB Decoding: AC3, MPEG-4(AAC-HE), MPEG-1 Layer1, 2 and 3 Sampling rate: 32 / 44.
Chapter2. Installation 12. Chapter2. Installation of Sezam Marvel This chapter will guide you through the whole installation process of Sezam Marvel. Please read each section carefully to make sure that the system runs properly. 2.1 Connecting Satellite Cables Sezam Marvel is integrated with triple satellite tuners, and one of the first steps is to connect satellite cable(s) to Sezam Marvel in order to gain optimal signal quality.
13. Installation B. Internal Loop-through In case you have only one satellite cable, connect the cable to TUNER A Input. And then connection Tuner A output to Tuner B input. C. DVB-T/T2 or DVB-C Cable In case you have DVB-T/T2 or DVB-C cable, connect the cable to TUNER C Input.
Chapter2. Installation 14. 2.2 Connecting the TV Sezam Marvel provides a variety of audio/video connection methods. A. Connecting TV via HDMI Cable For the sake of the best picture quality, especially for digital TV, HDMI connection is recommended. Most HDTVs have HDMI connectors to ensure the highest picture quality. In the rear panel of Sezam Marvel one HDMI connector is available for this purpose. B. Connecting TV via RCA (Video) Cable Sezam Marvel provides Composite video connection as well.
15. Installation C. Connecting TV via Component Cable The secondly recommend TV connection for digital TV is via component cable (YPbPr). However, unlike the HDMI connection which delivers audio and video signal at the same time, YPbPr connection requires additional audio connection either via RCA cable (Stereo L/R) or S/PDIF. NOTE: When you have an A/V receiver with S/PDIF digital audio input, this connection is recommended to enjoy the best audio quality, especially for the Dolby Digital sound. D.
Chapter2. Installation 2.3 Connecting Power A power unit is provided as one of the basic accessories of Sezam Marvel. ● Connect the power unit to the connector at the rear panel of Sezam Marvel. Turn on the power switch at the rear panel. ● Support to 90 ~ 265 VAC, 50/60Hz. 16.
17. Installation 2.4 Power ON/OFF [Press ‘Standby/Restart’] There are several ways to turn your Sezam Marvel ON or OFF ● Complete Power Shutdown There is a Power Switch in the rear panel and once it is ON, you do not need to turn it on or off each time. It takes a longer time to boot the system if you turned it off by this switch. ● Standby Mode POWER key is normally used to turn the power of Sezam Marvel on or off. If you press POWER, it instantly switches your Sezam Marvel off or on.
Chapter3. First Time Installation 18. Chapter3. First Time Installation When you turn on Sezam Marvel for the first time after purchase, an installation wizard will begin step by step. NOTE: ‘OK’ key is used for confirmation and turns to the next step. Press ‘EXIT’ key to return to the previous page. Step 1. Language Selection Sezam Marvel provides various languages and here you can choose the main language for your Sezam Marvel. Use UP/DOWN key to scroll up and down to find the language you want.
19. First Time Installation Step 3. Video Mode Selection Sezam Marvel provides various video modes. You can choose one. Use UP/DOWN key to scroll up and down to find the mode you want. Step 4. User interface and DHCP Step 5.
Chapter3. First Time Installation Step 6. Configuring mode Using LEFT/RIGHT key, you can choose one of the following Configuration Modes: ● Not configured. ● Simple ● Loop-through to: mode to make the TUNER B be internally connected from the TUNER A. ● Equal to: mode to use the same configuration as that of Tuner A. ● Advanced: for an advanced user configuration. Not configured loopthough to equal to Advanced 20.
21. First Time Installation Step 7. Configuring Tuner A Using LEFT/RIGHT key, you can choose one of the following Configuration Modes: ● Not configured ● Simple ● Loop-through to: mode to make the TUNER A be internally connected from the TUNER B ● Equal to: mode to use the same configuration as that of Tuner B.
Chapter3. First Time Installation Single This option is used to receive a single satellite with a single LNB. The cable from LNB is directly connected to Sezam Marvel. ToneBurst A/B This option is used if you want to receive two satellites using a ToneBurst switch. DiSEqC A/B This option allows you to configure two satellites in Port A and Port B. 22.
23. First Time Installation DiSEqC A/B/C/D This option allows you to configure four satellites in Port A, Port B, Port C, and Port D. Positioner This option is used when you have a motorized satellite antenna. Step 8. Configuring Tuner B This step is for the configuration of TUNER B Input and the process is same as that of Tuner A. For further information please refer to the above “Step 7. Configuring Tuner A” section.