Test Equipment Catalogue 2007 Trusted by professionals Martindale Metrohm Drummond
Contents 16th Edition Testing 02 Phase Rotation 44 Metrohm 16 Decade Boxes 45 Multi & Clamp meters 19 Fuse Finders 46 Pat testers 27 Thermometry 48 Kits 35 Environmental 52 Sockets Testers 36 Calibration & Service 57 Voltage Indication 40 Drummond 60 Continuity Testers 43 Test Leads 62 ! WARNING! Test equipment is designed for use only by competent persons with appropriate qualifications and experience.
Introduction MARTINDALE ELECTRIC Martindale manufactures a wide range of electrical test equipment. Trusted by professionals Quality System registered to ISO 9001: 2000 Martindale is a member of Gambica, the UK’s representative body for test equipment.
16th Edition and Part P testing page 03 VR2230 all-in-one Part P tester 03 VR2240 all-in-one downloading tester 04 VR2250 all-in-one tester with power analysis 05 2 insulation tester comparison chart 06 IN2101 digital low cost insulation tester 06 IN2102 digital insulation tester 07 IN2103 digital insulation tester 08 IN1001 500V analogue insulation tester 08 IN1003 250V/500V/1000V analogue insulation tester 09 IN2001 500V range insulation tester 09 IN2003 250V, 500V, 100V r
Part P/ BS 7671 / 16th Edition VR2230 Insulation Ranges: 0.05MΩ to 1999MΩ at voltages between 50VDC, 100VDC, 250VDC, 500VDC, 1000VDC with a resolution of 0.01MΩ, 0.1MΩ and 1MΩ Continuity Ranges: 0.01Ω-19.99Ω (0.01Ω res) 20.0Ω-99.9Ω (0.1Ω res) All-in-one tester The first in a series of three testers, the VR2230 is an ideal Part P tester.
16th Edition / BS 7671 / Part P All-in-one tester VR2250 Main Features Include: • Continuity test • Insulation resistance test • Non Trip Earth Loop test • RCD test • Phase Rotation test • Power Analyser • Earth Soil Resistivity • 999 memory Slots • Downloadable to PC • Backlight Insulation Ranges: 50VDC, 100VDC, 250VDC, 500VDC, 1000VDC Continuity Ranges: 0.01Ω-9.99Ω (0.01Ω res) 10.0Ω-99.9Ω (0.1Ω res) RCD Ranges: 10mA, 30mA, 100mA, 300mA, 500mA. Earth Loop Ranges: 25A 0.03Ω-19.99Ω (0.
Part P/ BS 7671 / 16th Edition Insulation Tester Comparison Chart A choice of 7 insulation testers from low cost, value-for-money, to cutting-edge technology.
16th Edition / BS 7671 / Part P 500V Low Cost Insulation Tester IN2101 Insulation: 0.200MΩ - 4,000MΩ at 500V in 4 ranges, with automatic discharge The new 16th Edition (BS EN 61557) testers from Martindale give high quality, accurate testing at low costs. These meters comply fully with all UK and international standards. Accuracy: ± (3% rdgs + 5 digits) Continuity: 0.1Ω - 40Ω, 0.
Part P/ BS 7671 / 16th Edition IN2103 Professional Insulation Tester Insulation Tests: 250V: 4/40/400/1000MΩ 500V: 4/40/400/4000MΩ 1000V: 4/40 /400/5000MΩ Range: 0.200MΩ to 5000MΩ Short Circuit Current: <1.5mA Accuracy: ± (3% rdgs + 5 digits) Auto-Discharge: Yes Buzzer disable option: Yes Continuity: Range: 0.01Ω to 40.00Ω Resolution: 0.01Ω Short Circuit Current: >200mA Accuracy: ± (3% rdgs + 5 digits) Auto-Discharge: Yes Buzzer: <30Ω Resistance: Range: 0.
16th Edition / BS 7671 / Part P 500V Analogue Insulation Tester IN1001 Insulation Test: 500V Insulation range: 0-100MΩ (500V) This analogue insulation and continuity tester is designed to carry out testing in accordance with national and international standards. Voltage V~ Range: 0-500V AC Accuracy: ±3% of full scale Input Impedance: 250KΩ nominal It has a ‘push to operate’ and ‘turn to latch’ test button on the insulation ranges as standard.
Part P/ BS 7671 / 16th Edition IN2001 Insulation: 10kΩ to 100MΩ at 500V Continuity: 0 - 20Ω, 0.01Ω resolution 0 - 200Ω, 0.1Ω resolution (audible tone <1Ω) Voltage range: 500V AC Accuracy: ± 2% of reading ± 1 Digit to 20MΩ ± 3% of reading ± 1 Digit to 100MΩ ± 10% of reading ± 1 Digit to 200MΩ Complies with: BS EN 61557, BS 7671, HD 384 and 16th Edition Housing: polycarbonate/ABS Dimensions: 190 x 90 x 54mm Weight: 0.
16th Edition / BS 7671 / Part P RCD Tester - Residual Current Device Tester RC2000 Supply Voltage: 240 Volts AC, 50/60Hz The RCD tester is fast and easy to use and suitable for testing all common RCDs up to 500mA. RCD Ratings (IΔN): 6 mA, 10mA, 30mA, 100mA, 300mA and 500mA Half trip settings (½xIΔN): 3mA, 5mA, 15mA, 50mA, 150mA and 250mA The RCD rating (IΔN) is set using the convenient centrally located rotary switch.
Part P/ BS 7671 / 16th Edition EZ2100 E-Ze Test ™ Nominal Voltage Rating: 220 - 240 V Voltage Range for Wiring Error Detection: 30 - 275 V Open Loop indication: If open PE or PN Loop is detected, no impedance measurement occurs Voltage Range for Impedance Measurement: 198 - 264 V Frequency: 50 Hz PE Loop Impedance Ranges: 0-8.99Ω, 9.0-89.9Ω, 90-899Ω, 900-1699Ω, 1700-3000Ω PE Loop Impedance Accuracy: 0 - 8.99Ω ± 4% ± 0.05Ω 9.0 - 89.9Ω ± 5% ± 0.
16th Edition / BS 7671 / Part P E-Ze Check ™ Xtra Non-Trip Earth Loop Impedance EZ150 Nominal supply: 230V, 50 Hz A unique new earth loop indicator with voltage and wiring checks. Earth loop impedance span: 0-1.7Ω, 1.7 to 5Ω, 5 to 10Ω, 10 to 100Ω, 100 to 200Ω, 200 to 500Ω Conventional indicators have the weakness that they only show if the earth is connected, they don’t indicate how safe it is. Earth loop threshold accuracy: ±(10% + 0.
Part P/ BS 7671 / 16th Edition CM67 Display: 4½ digit display AC mA: 0-30-300mA AC A: 0-30-60A AC V: 300V, 600V Earth Leakage Clamp Meter A very high quality earth leakage clamp meter with resolution down to 0.01mA and an accuracy of up to 0.05mA. Ideal for identifying appliances or circuits which are causing RCDs to trip. Accuracy: 1% ± 5 dgts Conductor Diameter: Max. 30mm Ø Operating Environment: 0°C to 40°C at <80% R.H. Battery Warning: BAT symbol shows when battery voltage is less than 2.5V ±0.
th Edition / BS 7671 / Part P 16th Edition / Part P Installation Kit KIT2000 IN2003 specification: see page 9 RC2000 specification: see page 10 LP2000 specification: see page 10 Includes: TL205 mains lead TL88 3 way fused leads TL47 unfused test leads batteries aluminium case For a full specification of each tester visit www.martindale-electric.co.uk “increases productivity by letting more than one person test at a time” Total value £958.
Part P/ BS 7671 / 16th Edition KIT2500 Professional 16th Edition/Part P Installation Kit IN2103 specification: see page 7 RCD specification: see page 10 EZ2500 specification: see page 11 Includes: TL205 mains lead TL88 3 way fused leads TL47 unfused test leads For a full specification of each tester visit www.martindale-electric.co.uk This kit complies fully with Part P.
Metrohm 4kV Flash Tester E3640 Power Requirement: 115/230 Volts ±15% 50/60Hz 40VA This digital flash tester is a portable mains operated instrument, capable of operating from either 115V or 230V supplies at 50/60Hz. It can apply up to 4kV AC and displays both output voltage and leakage current on the twin 3½ digit LCD’s. Fuses: 230V - 5x20mm 0.25A, HBC, Type F 115V - 5x20mm 0.5A, HBC, Type F Output Voltage Range: 0 - 2.2, 0 - 4.
Metrohm 7A501C Insulation Range: 0 - 50MΩ Test Voltage: 500V DC±10% across 1MΩ Short Circuit Current: <2mA Accuracy: ±1.6mm of scale arc length CONTINUITY Ω Range: 0 - 50Ω Test Voltage: Nominal 200mV Insulation Safety Insulation Tester Tester In service for 45 years in mines, on petrol sites and in hazardous areas e.g. in the presence of Methane, Ammonia and Hydrocarbons. This well proven design is a solution to carrying out electrical safety testing in hazardous environments.
Metrohm Earth/ Ground Tester E1610 Earth Resistance Ranges: 0 to 20Ω in steps 0.01Ω, 0 to 200Ω in steps 0.1Ω, 0 to 2000Ω in steps 1Ω ± 2% of reading ±2 digit This is a very handy, easily portable and simple to use earth tester. A large liquid crystal display shows earth/ground resistance and continuity. Test Current range: 10mA AC RMS nominal on 20Ω 1mA AC RMS nominal on 200Ω 0.
Multimeters & Clamps page 21 MM34 general purpose multimeter 21 MM35 autoranging multimeter 21 MM37 safety sensing multimeter 22 AM5 analogue multimeter 22 MM42 low cost multimeter 22 MM44 general purpose multimeter 23 MM45 autoranging multimeter 23 MM47 electrician’s multimeter with phase rotation & temperature 23 MM53 large format multimeter 24 MM84 true RMS multimeter 24 CT60 clamp adaptor 25 CM67 earth leakage clamp 25 CM52 200A mini clamp meter 25 CM54 1000A AC
Multimeters & Clamp Meters Multimeter Comparison Chart Best accuracies shown ± (% readings + digits) DCV ACV Ω MM34 1mV - 600V 2% + 1 100mV - 600V 2.5% + 4 0.1Ω - 20MΩ 2% + 1 MM35 100μV - 600V 0.8% + 1 100μV - 600V 2% + 4 0.1Ω - 30MΩ 1.5% + 3 MM37 0.1mV - 600V 1.2% + 1 100μV - 600V 2% + 4 MM42 1mV - 600V 1.2% + 1 MM44 ACA DCA Frequency Capacitance True RMS Holster Price 0.1μA - 10A 2.5% + 2 £27.80 0.1μA - 10A 2% + 4 0.1μA - 10A 2% + 1 £34.75 0.1Ω - 20MΩ 1.5% + 4 0.
Multimeters & Clamp Meters MM34, 35 & 37 Display: 3½ digit LCD display with automatic polarity indication and automatic zero. Diode test Overvoltage: CAT III 600V Dimensions: 143 x 68 x 47mm General Purpose Multimeter The MM34, low cost multimeter, has 4 main functions together with diode and battery test and a large clear display. The sculpted shape makes it comfortable to hold and easy to position the central rotary switch.
Multimeters & Clamp Meters Low Cost Digital Multimeter MM42 Display: 3½ digit display with automatic polarity and zero This is a simple low cost meter with all the basic multimeter functions including 1.5 & 9V battery test ranges. AC V: 100mV to 600V (2 ranges) (50Hz to 500Hz) DC V: 1mV to 600V (4 ranges) It has the same safety and reliability as the rest of the series but if 10A AC/DC current ranges and more advanced features are required see the MM44, MM45 or MM47 meters.
Multimeters & Clamp Meters MM45 Display: 3½ digit LCD with bargraph & automatic polarity & zero. AC V: 100μV to 600V (5 ranges) (50/60Hz) AC A: 0.1μA to 10A (5 ranges) (50 /60Hz) DC V: 100μV to 600V (5 ranges) DC A: 0.1μA to 10A (5 ranges) Ohms: 100mΩ to 32MΩ Autoranging Multimeter This high specification autoranging multimeter is fast, safe and simple to use. The range hold and change buttons give the option of full measurement control. The addition of a bargraph assists with varying signals.
Multimeters & Clamp Meters True RMS Multimeter MM84 Display: 4½ digit display with large 17mm digits. This is Martindale’s top of the range multimeter. It combines a large 4½ digit display with a basic accuracy of 0.05% and true RMS capability. AC V: 10μV to 750V (5 ranges) (50Hz to 500Hz) True RMS AC A: 10μA to 20A (5 ranges) (50 Hz to 500Hz) True RMS It accurately measures the frequency of mains supplies and up to 20A AC or DC.
Multimeters & Clamp Meters CM67 Display: 4 digit display AC mA: 0-30-300mA AC A: 0-30-60A AC V: 300V, 600V Earth Leakage Clamp Meter A very high quality earth leakage clamp meter with resolution down to 0.01mA and an accuracy of up to 0.05mA. Ideal for identifying appliances or circuits which are causing RCDs to trip. Accuracy: 2% ± 5 dgts Dimensions: 212 x 42 x 30mm Weight: 220g approx Display hold helps use in awkward places. Low pass filter eliminates frequencies above 150Hz, avoiding false readings.
Multimeters & Clamp Meters 1000A AC Clamp Meter CM56 Display: 3½ digit LCD bargraph This has a large display combining a clear 3½ digit readout with a responsive 34 segment bargraph, useful for representing varying signals. AC V: 1mV to 750V, autoranging (50Hz to 300Hz) (4 ranges) Accuracy: ± (1.5% rdg + 4 dgts) AC A: 10mA to 1000A (3 ranges) (50Hz to 400Hz) For general purpose use it is autoranging on AC and DC voltage, with resistance to 30MΩ and a beeper for the low resistance continuity range.
PATs page 28 EPAT1600 “legal minimum” manual PAT tester 29 EPAT2100 manual PAT tester with flash 30 LAB1 small pass labels 30 POLY1 polyester pass labels 30 LAB2 paper pass labels 30 FAIL1 fail labels 30 MS1 mark & seal labels 30 BAR1 appliance barcode labels 30 BAR2 combined barcode & pass appliance labels 30 MICRO microwave test labels 31 MPATPLUS micropat+ downloading PAT tester 32 SHISFEXPRESS shire express software 32 TL151-TL154 three phase adaptor leads 32 BAR
Pats & Accessories EasyPAT Manual PAT Tester - legal minimum EPAT1600 • Does both mandatory tests and has a built in fuse test • 25A, 8A and 100mA (for computers, etc) earth bond tests selectable with a simple rocker switch • • INSULATION TEST Test Voltage: 500V DC -0% +20% at 0.5MΩ Short Circuit Current: 1.5mA DC nominal Display Range: 0 - 19.9MΩ Accuracy Of Indication: ±5% of reading ±1 digit EARTH CONTINUITY (8A & 25A) Test Voltage: 6V AC nominal with no load Test Current: 25A AC nom @ 0.
Pats & Accessories EPAT2100 EasyPAT Manual PAT Tester - professional INSULATION TEST Same as EasyPAT 1600 (see opposite) EARTH CONTINUITY (8A & 25A) Same as EasyPAT 1600 (see opposite) • Does ALL 5 tests • Tests at either 110V or 230V, dependant on supply voltage • No need for computer links • 25A, 8A and 100mA (for computers, etc) earth bond tests selectable with a simple rocker switch • Now supplied complete with a built in extension lead tester • Tests 110V appliances from 110V supplies and
Pats & Accessories Small Pass Labels LAB1 Paper labels suitable for plug tops and use on small appliances. Rolls of 500 (30 x 20mm) MARLAB1 £12.50 G Pass Labels POLY1 These are higher quality pass labels made of polyester for harsh environments, or if subject to frequent cleaning and abrasion. Rolls of 500 (50 x 25mm) MARPOLY1 £27.00 G Pass Labels LAB2 Paper pass safety test labels are designed to be replaced with each inspection. Rolls of 500 (60 x 30mm) MARLAB2 £13.
Pats & Accessories MPATPLUS MicroPAT + Downloading PAT Tester INSULATION TEST Test Voltage: 500V DC - 0% + 20% Short Circuit Current: 1.5mA DC nominal Display Range: 0 to 19.9MΩ Accuracy: ±5% ±1 digit EARTH CONTINUITY TEST Test Voltage: 6V AC nominal with no load Test Current: 25A AC nominal 100mA (soft test) for IT equipment Display Range: 0 to 1.99Ω Accuracy: ±10% ± 1 digit “Well specified downloading tester with simple 2 digit test codes” RUN CURRENT TEST Display Range: 0 to 3.
Pats & Accessories Shire Safety First Software SHISFEXPRESS Compatible With: Martindale recommends Shire software for use with the MicroPAT+. Windows 95/98 Windows 2000 Windows XP Windows NT4 Shire software allows maintenance of comprehensive data records downloaded from a PAT and information such as description and notes can be added. Individual certificates, customised with a logo, or lists of passed items can be printed out.
Pats & Accessories LT SERIES LTDV, LTDVR, LT240 & LT240R All models can be used to check the continuity/ bond of the safety earth and check the polarity of phase and neutral conductors. All models can be used to check conventional extension leads and IEC type detachable leads as found on IT equipment and domestic appliances. Applied Test Voltage: 110V ±10% or 240V ±10% 50/60Hz Installation (IEC1010): CAT II 300V Leads: 240V BS 1363 to IEC line socket.
Pats & Accessories Downloading PAT Tester Kit MARMPAT/BUND CONTAINS Micropat + Appliance Tester Appliance Pass Labels (500) Fail Labels (100) Data Lead (Pat Tester - PC) Shire Safety First Express CCD Barcode Reader (Micropat) LTDV Ext Lead Tester IEE Pats Code of Practice Pat 3 Phase Adaptor 16A 4 Pin Pat 3 Phase Adaptor 16A 5 Pin Pat 3 Phase Adaptor 32A 4 Pin Pat 3 Phase Adaptor 32A 5 Pin total va £200 lue 3.
Kits KIT2000 IN2003 specification: see page 9 RC2000 specification: see page 10 LP2000 specification: see page 10 Includes: TL205 mains lead TL88 3 way fused leads TL47 unfused test leads batteries aluminium case 16th Edition/ Part P Installation Kit This kit is the ideal solution to 16th Edition testing. It contains an IN2003 250/500/1000V insulation tester, LP2000 loop and PSC tester and RC2000 RCD tester, together with TL88 3 way fused test leads and IEC mains lead.
Socket Testers page 36 37 CP501 classic check plug 37 BZ101 buzz-it check plug with sounder 38 CP201 250V industrial check plug 38 CP301 110V industrial check plug 38 PC101 3 phase industrial check plug with phase rotation 39 EZ150 non-trip earth loop impedance checker 39 EZ650 non-trip earth loop impedance checker kit
Socket Testers CP501 Mains supply: 200-250V(30-70Hz) Power consumption: <1.2W Temperature range: -10°C to 40°C 60% RH (max) Earth leakage: <5mA Overvoltage: CAT II/300 V Housing: Flame retardant ABS Dimensions: 65 x 65 x 47mm Like all other socket testers these units cannot detect common earth and neutral or earth neutral reversal. Classic Check Plug The check plug is a fast and easy way to ensure that 13A sockets are wired correctly, indicated by all three high brightness, long life, neons illuminating.
Socket Testers 250V Industrial Check Plug CP201 For factory and industrial maintenance, the 250V Industrial Check Plug (CP201) is fitted with a standard blue 250V 16A BS 4343/IEC309 plug (round 3 pin). Operating Voltage: 250V AC Power consumption: <1.2W Overvoltage: CAT III/250V Weight: 180g approx Simply plug it into an appropriate socket outlet and it will instantly identify whether or not the socket is correctly wired, in the same way as the classic check plug.
Socket Testers E-Ze Check Xtra ™ Earth Loop Impedance Indicator EZ150 Nominal supply: 230V, 50 Hz Earth loop impedance span: 0-1.7Ω, 1.7 to 5Ω, 5 to 10Ω, 10 to 100Ω, 100 to 200Ω, 200 to 500Ω Earth loop threshold accuracy: ±(10% + 0.3Ω) This is the first socket tester that gives a measurement of the earth loop impedance. This is the only safe solution for socket testing, as other testers can indicate as “safe” a socket with a dangerously high earth resistance.
Voltage Indication page 41 VI13700G safety voltage indicator 41 PD690 proving unit 42 TEK100 non-contact voltage indicator 42 TEK200 non-contact voltage & magnetic pole indicator See pages 60 & 61 for Drummond test lamps 40
Voltage Indication VI13700G Voltage Ranges: AC 0 - 49V none lit 50 - 99V one lit 100 - 199V two lit 200 - 399V three lit 400V+ all it DC 0 - 74V none lit 75 - 149V one lit 150 - 239V two lit 240 - 559V three lit 560V+ all lit Operating temperature: -20°C to 50°C Overvoltage: CAT III/600V IMPORTANT: Voltage indicators should always be tested with a proving unit or known live source before and after use - see PD690 below Safety Voltage Indicator Before doing any electrical work it is essential to be absolute
Voltage Indication Non-Contact Voltage Indicator TEK100 Voltage Range: 100 to 600V AC. This is suitable for detecting 100V to 600V AC without requiring physical contact with the conductor. Frequency Range: 50Hz to 50kHz. Integrated self test proving function The presence of any voltage between 100V and 600V AC will generate an audible tone, together with a red visual indication.
Continuity Testers TEK402 Probe Voltage: 9V Test Current: 5mA Resolution Range: 0 - 170kΩ audible Output: 85dB minimum at 30cm, zero resistance Audible Frequency: 2.8kHz ± 0.1kHz Supply: 9V, MN1604/PP3 alkaline battery (excluded) Continuity Tester with Audible Indication This is a low cost, easy to use continuity tester with audible indication. The loud buzzer makes it easy to use in noisy environments. Its simplicity and tough construction gives fast and simple continuity testing at a low cost.
Phase Rotation Phase Rotation & Continuity Indicator PC15250 For use on systems from 100V to 600V phase to phase, 40Hz to 60Hz. This continuity indicator will quickly and simply prove continuity of all three lines, (or identify which are faulty) and shows the sequence of phase rotation. Operating temperature: -20°C to 50°C It gives a fast, effective method of identifying worn or unmarked cables, and ensures 3-phase outlets and machines are wired correctly.
Decade Boxes TEK903 Resistance: 1% Grade 0.6W per resistor variable from 10Ω to 11.1111MΩ ±1% in 6 ranges Dimensions: 306 x 70 x 80mm Weight: 404g approx TEK905 Capacitance: ±5% Grade 100 V DC variable from 100pF to 4.111μF± 5% in 5 ranges Dimensions: 306 x 70 x 80mm Weight: 425g approx Decade Resistance Box This is a very reliable decade resistance box with high quality rotary switches providing in-line readouts. Ideal for laboratory, educational and calibration applications.
Fuse Finders Standard Fuse Finder Kit - FD500 The analogue Martindale Fuse Finder Kit (FD500) finds which fuse or breaker controls a circuit. It also enables tracing from socket to socket on a circuit. The transmitter (FD500/T) takes its power from the mains and emits a signal which the adjustable sensitivity receiver (FD500/R) can pick up. FD500 & FD600 This combination can easily distinguish the appropriate circuit, even on a crowded fuse board.
Fuse Finders FD550 & FD650 Transmitter Voltage rating: 230V Frequency range: 50-60Hz Switching frequency: approx. 5Hz Transmission pulse width: approx.1.7μS Transmission pulse amplitude: 20A max Earth Leakage: Nil Power consumption: Approx. 1W Protection Class: IP20 Overvoltage: CAT III/300V Elite Fuse Finder - FD550 The Digital Elite Fuse Finder brings microprocessor controlled multi-level sensitivity to fuse and breaker identification.
Thermometry page 48 49 DT75 dual input thermometer 49 THERMOKIT thermometry kit 50 TT1P & TT1KF thermocouples 50 TT5K air probe 50 TT8K surface probe 50 TT10K pipe clamp 50 TT4K & TT4KSP high temperature probes 50 TT6K & TT6T penetration probe 51 TT8KHD heavy duty surface probe 51 TT9K needle probe 51 TT12K velcro probe 51 TT14K oven probe 51 TT15K heavy duty needle probe 51 TT18 between pack probe 51 TT20K binder probe
Thermometry DT75 Display: 3½ digit liquid crystal display (LCD) with a maximum reading of 1999. Sampling Rate: 3 times per second Supplied Probe: 4-foot type “K” thermocouple bead probe (teflon tape insulated). Maximum insulation temperature 260°C (500°F). Probe accuracy ±2.2°C or ±0.75% of reading (which ever is greater) from 0°- 800°C. Digital Thermometer This is a high quality dual-input digital thermometer with temperature difference capability.
Thermometry Thermocouples T T1P & T T1KF T T1P & T T1KF The TT1P is a flexible general purpose bead K-Type thermocouple, PTFE insulated cable with mini plug. The TT1KF is a simple general purpose bead K-Type thermocouple, fibreglass insulated cable with mini plug. MARTT1P thermocouple PTFE insulation £6.75 MARTT1KF thermocouple fibreglass insulation £8.75 Air Probe T T5K TT1P Temperature Range: -75 to 250°C Dimensions: Ø1.5 x 1000mm TT1KF Temperature Range: -75 to 350°C Dimensions: Ø1.
Thermometry T T8KHD Temperature range: -50 to 1000°C Dimensions: Ø12 x 130mm Heavy Duty Surface Probe T T8KHD This heavy duty surface probe is suitable for measuring a variety of surface temperatures. MARTT8KHD T T9K Temperature range: -50 to 250°C Dimensions: Ø1.8 x 130mm Temperature range: -50 to 100°C Dimensions: 20 x 500mm This handheld needle probe is ideal for penetrating soft materials. Suitable for a variety of industrial applications. T T14K Dimensions: Ø3.
Environmental page 52 53 TEK500 microwave leakage detector 53 CO90 carbon monoxide meter 54 SP75 sound level meter 54 LM90/92 light meters 55 IR90 infrared and k-type thermometer 55 IR88 infrared gun-type thermometer 55 AV90 anemometer with external probe 56 TEK300 process control calibrator 56 TEK600 cable and pipe detector
Environmental TEK500 Detection frequency range: 2450MHz ± 25MHz Sensor distance: The fixed cone on the rear of the unit should be in gentle contact for the standard 50mm separation. Indicators: Test position: All four LEDs should light and an audible tone will be emitted.
Environmental Sound Level Meter SP75 Applicable Standard: IEC 651-1979 Type 2, ANSI S1.41983 Type 2, JIS C 1502 This compact sound level meter can be used one handed or it can be mounted on a tripod for measuring over long periods. Measurement Range: Lo - range 35-90 dB, Hi - range 75-130 dB Measurement rate: once per sec, nominal The Time Weighting can be set to Slow (for normal use) or Fast to check the average level of frequency noise. Display: 3½ digit LCD Resolution: 0.
Environmental IR88 Infrared Gun-Type Thermometer Range: -30°C to 550°C /-22°F to 1022°F Resolution: 0.5°C/1°C (AUTO), 1°F This pistol style infrared thermometer has a laser marker to ensure accurate spot measurement. The display can show temperatures in Fahrenheit or Celsius. Accuracy: ±(2°C/4°F) for -30°C to 100C, -22°F to 212°F A limit function sets upper and lower temperature thresholds and a tone alerts if the limits are exceeded.
Environmental Process Control Current Calibrator TEK300 DC/DC Converter Output: 28.5V (+0.1V) This Martindale current calibrator has sink, source and monitor modes for 0 to 20mA. Current Range: 0 - 20mA F.S. (+0.1%) It is ideal for most process control as well as general purpose, signal injection applications. Resolution: 10μA Temperature Drift: 150ppm/°C This handheld, fully portable unit has a 3½ digit display with overload protection for additional safety. Linearity: +0.
Calibration and Service Martindale offers a full and comprehensive calibration and repair service for Martindale and most other manufacturers’ equipment. Calibration prices are competitive and are quoted alongside each product in the catalogue. Turnaround times vary but instruments are usually returned within 5 working days.
Calibration & Service All Martindale instruments are supplied calibrated, but personalised certificates are chargeable. We use computer driven procedures to ensure a consistent, repeatable approach. Centralised records also allow us to maintain traceability and to generate reminders for recalibration when next due. Additionally we offer calibration across a wide range of electrical test equipment from other manufacturers.
Calibration & Service SPECIAL TERMS APPLY INSULATION TESTERS TYPE Martindale IN2001/IN2003 IN2101/IN2103 16 Series 7A Metrohm Other similar PRICE £27.00 £27.00 £27.00 £27.00 £27.00 EARTH TESTERS TYPE PRICE Metrohm Other similar E1610 £39.00 £39.00 DT75 £27.00 IR90 IR88 £55.00 £55.00 £27.00 £55.00 THERMOMETERS Martindale RCD TESTERS Martindale Metrohm Metrohm Other similar RC2000 9B 16R £27.00 £27.00 £27.00 £27.
Drummond Test Lamps The Drummond range of test lamps all offer exceptional build quality and performance. The main body and probe incorporate large finger guards for user safety. Housed in a tough moulded body is a 240V 15W special rough service filament lamp which is shielded by a translucent cover. An HRC fuse is incorporated within the body for electrical protection. A 1.3m long double insulated EPR/CSP cable connects the main body to the probe.
Drummond MTL9c IMPORTANT: Voltage indicators should always be tested with a proving unit or known live source before and after use - see PD690 shown below. Complies with GS38 and G9/6 Double insulated oil resistant and flame retardant cable with black outer and white inner for easy detection of cuts and abrasions. HRC fuse PD690 Output Voltage: 230V into a 5kΩ load 700V into a 700kΩ load Test Lamp - MTL9c The test lamp incorporates a continuity tester attached to the test lead.
Test Leads & Accessories Selecting the Right Leads C - Right angle fixed shroud X - IEC lead Choose the type of probes and/or croc clips you need. Do you require fused leads for extra safety and GS 38 compliance? Then select the appropriate fittings to connect to your meter. ‘C’ end fits most modern multimeters including MM series, Fluke 10, 70 & 80 series. Best suited to meters with sockets on the front panel.
Test Leads & Accessories Loop Tester & Fuse Finder Leads TL83: 2-wire with croc clips supplied with X (IEC) connector 500mA fused (Martindale fuse finders only). TL84: 2-wire, two probes with croc clips supplied with Z (IEC “Hot”) connector - 10A fused. TL85: 2-wire, two probes with croc clips supplied with X (IEC) connector - 10A fused. TL64: Loop tester unfused wander earth probe. MARTL83 £34.75 MARTL84 £34.75 MARTL85 £34.75 MARTL64 £9.
Test Leads & Accessories 4mm multimeter leads Metrohm DFH0369 flash gun for E3640 DFK0075/A replacement 2m test leads for METE3511 DFK0075/C 10m test leads for METE3511 DFK0113 test leads for 7A501C PA24249A £65.00 £140.00 £175.00 £23.00 £52.00 N TL45 N N N N £19.95 double insulated PVC leads - C right angle fixed shroud TL46 £22.75 double insulated PVC leads - D sprung retractable shroud TL47 £19.95 double insulated PVC leads - E straight fixed shroud TL48 £22.
Just look at our range • calibration To ensure your equipment remains in specification throughout its life Martindale offers a calibration service on all the equipment in this catalogue. • repair In the unlikely event of your tester failing Martindale offers a full repair service to restore your instrument to its original specification. • training We currently provide PAT training, at our premises or yours.
• • • • • • • • • • 16th Edition testers All-in-one’s Calibration equipment Continuity testers Electrician’s kits Full calibration & repair service Fuse finders Digital clamp meters Digital multimeters Microwave leakage detectors Martindale Metrohm Drummond • Non-trip loop testers • Pat testers & accessories • Phase rotation • Proving units • Socket testers • Thermometers & probes • Test leads • Voltage indicators • Specialist Metrohm testers (4 & 5kV) • Specialist Drummond testers Trusted by profession
