User manual

MAC III Performance DMX protocol 53
33 39
0 - 9
10 - 14
15 - 19
20 - 24
25 - 29
30 - 34
35 - 39
40 - 44
45 - 49
50 - 54
55 - 59
60 - 64
65 - 69
70 - 74
75 - 79
80 - 84
85 - 89
90 - 94
95 - 99
100 - 139
140 - 144
145 - 149
100 - 154
155 - 159
160 - 164
165 - 169
170 - 174
175 - 199
200 - 204
205 - 209
210 - 214
215 - 219
220 - 224
225 - 239
240 - 244
245 - 249
250 - 255
0 - 1
2 - 3
4 - 5
6 - 7
8 - 9
10 - 11
12 - 13
14 - 15
16 - 17
18 - 19
20 - 21
22 - 23
24 - 25
26 - 27
28 - 29
30 - 31
32 - 33
34 - 35
36 - 37
38 - 53
54 - 55
56 - 57
58 - 59
60 - 61
62 - 63
64 - 65
66 - 67
68 - 77
78 - 79
80 - 81
82 - 83
84 - 85
86 - 87
88 - 93
94 - 95
96 - 97
98 - 100
Fixture control/settings
No function
Reset entire fixture
(1)
Reset dimmer and shutter only
(1)
Reset CMYC and color wheel only
(1)
Reset effects module (gobo wheel, framing, gobo animation, iris, frost) only
(1)
Reset zoom and focus only
(1)
Reset pan and tilt only
(1)
No function
Lamp on
Lamp off
(1, 2)
No function (Note: this value is used for managing pan/tilt limits and storing
calibration values on channel 34/40)
Dimmer curve = Optically linear
(menu override, setting unaffected by power off/on)(2)
Dimmer curve = Square law
(menu override, factory default setting, setting unaffected by power off/on)(2)
Dimmer curve = Inverse square law
(menu override, setting unaffected by power off/on)(2)
Dimmer curve = S-curve
(menu override, setting unaffected by power off/on)(2)
No function
Pan & tilt speed = Normal (menu override - Setting returns to MENU setting
after power on/off)
(2)
Pan & tilt speed = Fast (menu override - Setting returns to MENU setting after
power on/off)
(2)
Pan & tilt speed = Slow (menu override - Setting returns to MENU setting after
power on/off)
(2)
No function
Parameter shortcuts = ON
(menu override, setting stays at factory default ON at power off/on)
(2)
Parameter shortcuts = OFF
(menu override, setting returns to factory default ON at power off/on)
(2)
No function
Disable zoom/focus linking
(2)
Enable zoom/focus linking, near distance
(2)
Enable zoom/focus linking, medium distance (factory default setting)
(2)
Enable zoom/focus linking, far distance
(2)
No function
Ballast output full, set to 1500 W
Ballast output reduced, output set to 1200 W
Ballast output reduced, output set to 1100 W
Ballast output reduced, output set to 1000 W
Ballast output reduced, output set to 900 W
No function
Illuminate display on fixture
(2)
No function
Trigger event log (inserts new dynamic content into current report)
(1)
If DMX Reset or DMX Lamp Off are disabled in the control menus, a full or
partial reset command or a lamp off command can be executed only if:
Slot 1 is selected on the color wheel (DMX value 20 on channel 7
in16-bit or 8 in 16-bit ext.), and
The beam effect (frost filter or prism) is on (DMX value 20-59 on
channel 24 in 16-bit or 28 in 16-bit ext.), and
Open gobo is selected on the gobo wheel (DMX value 0 on channel 8 in
16-bit or 9 in 16-bit ext.)
(2)
Value must be held for 5 seconds to activate
Basic
16-bit
Mode
16-bit
Extended
Mode
DMX Value Percent Function
Table 3: MAC III Performance DMX Protocol