Owner manual

ManualsBrandsMartin Universal Design ManualsSports and recreationU-145N Avanti Master Studio Art Easel

U-145N • Avanti Master Studio Art Easel

ASSEMBLY INSTRUCTIONS

MAKE SURE CARTON CONTAINS THE FOLLOWING PARTS

WOOD PARTS

Quantity ........Description ID#

2 ea. .......Side Legs ( 1 Left & 1 Right) [A]

1 ea. .......Center Mast Column [B]

1 ea. .......Rear Spike Leg [C]

1 ea. .......Metal/Wood Ratchet Column [D]

1 ea. .......Upper Cross Member [E]

1 ea. .......Lower Cross Member [F]

1 ea. .......Upper Canvas Support [G]

1 ea. .......Lower Canvas Support [H]

2 ea. .......Wood Angle Brackets [J]

1 ea. .......Lower Canvas Support Bracket [K]

HARDWARE PARTS

Quantity ........Description ID#

4 ea. .......2-1/4” Bolts [L]

2 ea. .......“L” Threaded Bolts [M]

2 ea. .......Hex Nuts [N]

1 ea. .......Wing Bolt [O]

1 ea. ....... 2-1/8” Bolt [P]

2 ea. ....... 3” Bolts [Q]

3 ea. .......Wing Nuts [R]

3 ea. ....... Washers [S]

1 ea. .......Loop Mechanism [T]

2 ea. .......Small screws [U]

2 ea. .......Long Screws [V]

Center Mast

Column [A]

Left Side Leg

[B]

Right Side Leg

[B]

Upper Canvas Support

[G]

Rear Spike

Leg [C]

Lower Cross member

[F]

Wood Angle

Brackets

[J]

Metal/Wood

Ratchet Column

[D]

TOOLS INCLUDED

Quantity ........Description ID#

1 ea. .......Flat Wrench [W]

1 ea. .......Screwdriver [X]

2-1/4” Bolts

[L]

3” Bolts

[Q]

2-1/8” Bolts

[P]

Threaded “L” Bolts

[M]

Hex Nuts

[N]

Washers

[S]

Wing Bolt

[O]

Wing Nuts

[R]

Loop Mechanism

[T]

Small Screws

[U]

Lower Canvas Support

[H]

“U” Bracket for

Lower Canvas

Support [K]

Long Screws

[V]

Page 1

Upper Cross member

[E]

Summary of content (4 pages)

PAGE 1
U-145N • Avanti Master Studio Art Easel ASSEMBLY INSTRUCTIONS MAKE SURE CARTON CONTAINS THE FOLLOWING PARTS HARDWARE PARTS WOOD PARTS Quantity ........ Description 2 ea. ....... Side Legs ( 1 Left & 1 Right) 1 ea. ....... Center Mast Column 1 ea. ....... Rear Spike Leg 1 ea. ....... Metal/Wood Ratchet Column 1 ea. ....... Upper Cross Member 1 ea. ....... Lower Cross Member 1 ea. ....... Upper Canvas Support 1 ea. ....... Lower Canvas Support 2 ea. ....... Wood Angle Brackets 1 ea. .......
PAGE 2
For recommended assembly lay all wood parts on flat surface with all holes facing up. STEP 1. Attach lower canvas support [H] to center mast column [A] using the 2 ea. “L” Bolt [M] provided. First insert the shorter end of the “ L” Bolt into the holes on the sides of the center mast column [A]. STEP 4. Attach “U” bracket [K] to rear of lower canvas support [H] by using 2 ea. Long screws [V]. Secure using screwdriver provided. See FIG. 4 V K A H M FIG 1 STEP 2.
PAGE 3
STEP 7. Attach lower cross member [F] to left leg [B] and right leg [B] by lining up the angled joiner on the cross member to the slotted holes in the legs. Secure by using the 2 ea. 2-1/4” Bolt [L] and screw in with screwdriver provided. Making sure oval hole is positioned on top edge of cross member. See FIG 7 & 7B B STEP 10. Attach Upper Cross Member [E] by sliding it over the top of the Center mast Column [A] and continue sliding it down along the channels.
PAGE 4
STEP 13. Attach Upper Canvas Support [G] to Easel by sliding it downward from the top of the Center Column [A] gliding it along the channel. Secure at desired height by screwing in Wing Bolt [O] in hole on front of Upper Canvas Support [G]. See FIG 13. PLEASE NOTE: Loosen Wing bolt to move Upper Canvas Support to desired position whenever needed. Tighten Wing Bolt to secure. STEP 14. Adjusting height Lower Canvas Support. Insert finger in locking pin below Lower Canvas Support and pull outward.