Owner manual

ManualsBrandsMartin Universal Design ManualsFurniture92-3010 Weber Monster Amalﬁ Studio Easel

MAKE SURE CARTON CONTAINS THE FOLLOWING PARTS

WOOD PARTS

Quantity ........ Description ID#

2 ea. ........ Base Feet

[1]

2 ea. ........ Base Cross Members

[2]

2 ea. ........ Uprights

[3]

1 ea. ........

Channelled Center Column [4]

1 ea. ....... Material Tray

[5]

2 ea. ........ Channelled Side Columns

[6]

1 ea. ........ Ratchet Column

[7]

1 ea. ........ Lower Cross Member

[8]

1 ea. ........ Upper Cross Member

[9]

2 ea. ........ Extendable Rear Legs [10 & 11]

1 ea. ........ Adjustable Center Column

[12]

1 ea. ........ Upper Canvas Support [13]

HARDWARE PARTS

Quantity ........ Description ID#

4 ea. .. Bolts & Cams: 6 X 60mm [A]

16 ea. . Screws: 4 X 16mm [B]

2 ea. .. Bolts & Cams: 6 X 60mm [C]

4 ea. . Screws: 4 X 25mm [D]

1 ea. .. Loop Mechanism & [4] Screws [E]

4 ea. .. Bolts & Cams: 6 X 60mm [F]

2 ea. .. 6 X 70mm Bolt/Knob/Washer&Wood Washer [G]

2 ea. .. 6 X 45mm Bolt/Knob & Washers [H3]

2 ea. .. 6 X 40mm Bolt/Knob & Washers [H4]

2 ea. .. 5 X 35mm Screws [H5]

3 ea. .. Knobs: 2 same size one longer

4 ea. .. Castors: 2 locking, 2 not locking

TOOLS INCLUDED

Quantity ........ Description

1 ea. ........ Flathead Screwdriver - Red Handle

1 ea. ........ Phillips Head Screwdriver - Orange Handle

Page 1

4 X 25mm

Screws (4 each)

[D]

6 X 60mm

Bolt & Cams

(4 each)

[A]

6 X 70mm Bolts, Knobs, Washers

& Wood Washers (2 of each)

[G]

92-3010 • MONSTER AMALFI STUDIO EASEL

ASSEMBLY/SET-UP INSTRUCTIONS

[4] Floor Castors (2 Locking)

4 X 16mm

Srews for Castors

(16 each)

[B]

6 X 60mm

Bolt & Cams

(2 each)

[C]

3 X 12mm

Screws * Loop Mechanism

[E]

6 X 60mm

Bolt & Cams

(4 each)

[F]

6 X 45mm

Bolts, Knobs & Washers

(2 each)

[H3]

6 X 40mm

Bolts, Knobs & Washers

(2 each)

[H4]

5 X 35mm

Screws (2 each)

[H5]

3 Knobs

2 same size one longer

[unmarked]

Base Feet [1]

Side View

Top View

Base Cross Members

[2]

Uprights [3]

Channelled Center Column [4]

Material Tray [5]

Channelled Sides [6]

Ratchet Column [7]

Lower Cross Member [8] Upper Cross Member [9]

Extendable Rear Legs [10 & 11]

Adjustable Center Column [12]

Upper Canvas Support [13]

Summary of content (7 pages)

PAGE 1
92-3010 • MONSTER AMALFI STUDIO EASEL ASSEMBLY/SET-UP INSTRUCTIONS MAKE SURE CARTON CONTAINS THE FOLLOWING PARTS WOOD PARTS Quantity ........ Description 2 ea......... Base Feet 2 ea......... Base Cross Members 2 ea......... Uprights 1 ea......... Channelled Center Column 1 ea. ....... Material Tray 2 ea......... Channelled Side Columns 1 ea......... Ratchet Column 1 ea......... Lower Cross Member 1 ea......... Upper Cross Member 2 ea......... Extendable Rear Legs 1 ea.........
PAGE 2
IMPORTANT - READ ALL INSTRUCTIONS BEFORE ASSEMBLING EASEL and USE 2 PEOPLE WHEN ASSEMBLING! STEP 1. Attach the [4] castors to the two base feet (1) making sure the 2 locking castors are positioned in the rear. NOTE: the rear of the base has the hole nearest that castor position. Secure with four screws (B) per castor. See FIG 1. STEP 4. Turn your base assmebly over onto the castors and you should now have a base that is assembled like FIG 4. 2 FIG 1 Rear of the base with hole. 1 1 1 STEP 2.
PAGE 3
STEP 6. Attach Material Tray (5) to Channelled Center Column (4) using four 4 X 25mm Screws (D). See FIG 6a & FIG 6b. 4 STEP 8a. Assembling the H-Frame. This step involves assembling parts (6, 7, 8 & 9) to form the H-Frame portion of the easel. Begin by taking the channelled sides (6) & the upper cross member (9) and inserting the oval male ends of the upper cross member into the oval holes of the channelled sides. See FIG 8a.
PAGE 4
STEP 10. Finish assembling the H-Frame by attaching the lower cross member (8) to the ratchet column (7) by inserting the ratchet column down into the oval hole of the lower cross member. Secure by ﬁtting the lower cross member into the oval holes of the channelled sides (6). See FIG 10. Secure this step, using two 6 X 60mm bolts and Cams as previously described in earlier steps. (as in Step 3) STEP 12. Attach assembled H-Frame to easel uprights found on assembled base.
PAGE 5
STEP 14. Attach Extendable Rear Legs (10&11) to base (1) and upper portion of Channelled Sides (6). Attach the wider end of the adjustable Rear legs (10) to the base by securing with one 5 X 25mm Screw. See FIG 14 for proper location. Secure with Phillips screwdriver. Repeat with other Extendable Leg. FIG 14 STEP 15. Attach upper portion of Extendable Rear Legs (11) to upper portion of Channelled Sides (6).
PAGE 6
STEP 18. Once Channelled Center Column is in its proper location in the upper Cross Support, secure with the longest of the three remaining knobs by threading the threads of the knob in the hole in the rear of the cross support. Tighten to secure. See FIG 18. 4 STEP 20. Final step involved in the assembly of your New 92-3010 Easel. Attach the Upper Canvas Support (13) to the Adjustable Center Column (12) by sliding the grooves of the canvas support down into the channels of the Adjustable Center Column.
PAGE 7
92-3010 Weber Monster Amalﬁ Studio Easel Upper Canvas Support (13) Adjustable Center Column (12) Upper Cross Member (9) Extendable Rear legs (11) Adjustable Material Tray (5) Height Adjustable Center Column/Material Tray by pulling loop out from ratchet system Ratchet Cloumn (7) Lower Cross Member (8) Uprights (3) Extendable Rear legs (10) Base Foot (1) Locking Castor Base Cross Support (2) Martin/F. Weber Co.