MAC 2000 Profile II user manual
133½° 133½° 271 759 10° 28° 743 613 488 171 min c/c 408 270° 545 270° 490 530 © 2000-2002 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark. P/N 35000090 Rev.
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TRANSPORTATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Included items. . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION Thank you for selecting the MAC 2000 Profile II. This extraordinary 1200 watt luminaire from Martin Professional provides CMY color mixing, continuous 0 - 178 mireds color correction, a color/gobo wheel with 4 dichroic color filters and 3 fixed glass gobos, 10 indexed-rotation gobos on 2 wheels, a 2-position rotating-effect wheel with 3-facet prism, beam shaper, and variable frost; combined full-range dimmer and shutter, iris, zoom, focus, 540° of pan, and 267° of tilt.
TRANSPORTATION Important! Release the transport locks before operating the fixture. Included items The MAC 2000 Profile II is shipped in a 1 or 2 unit flight case that contains the following items. • • • • • User manual 2 clamp attachment brackets 2 x 20 A main fuses (for use with 100-130 V local power supply) 2 x 15 A main fuses (for use with 200-250 V local power supply) XLR cable Transport locks The head and yoke may be locked for transportation and service. The locks are shown in Figure 1.
Double flight case Unpacking 2 Release the head (tilt) transport lock. 3 Install rigging hardware as described on page 12. 4 With one person on each side, lift the fixture out of the flight case. R Open the flight case and pull the drawer all the way out. F 1 O N T Packing 1 Disconnect the fixture from power and allow it to cool. 2 Turn the yoke parallel to the sides of the base with the tilt lock closest to the back. 3 Pull the transport drawer all the way out.
LAMP About the HMI 1200 W/S lamp TOP The MAC 2000 Profile II comes with a double-ended OSRAM HMI 1200 W/S discharge lamp installed. This highly-efficient short-arc source provides an exceptionally stable 6000K color temperature, a color rendering index greater than 90, and an average life of 750 hours. TOP The lamp is capable of hot restrike. This feature, however, is only supported by the MAC 2000 Profile II with electronic ballast.
4 See Figure 6. With the nipple on the bulb facing the back, insert the right end of the new lamp in the socket. Pull up on the left spring and snap the other end into place. 5 Lift the lamp assembly so that lamp is level with the center of the reflector. Push the assembly straight in until it seats, making sure the lamp passes through the reflector opening. Lock the 4 quarter-turn fasteners. 6 When installing a new lamp, reset the lamp hour and lamp strike counters as described on page 14.
AC POWER WARNING! For protection from electric shock, the fixture must be grounded (earthed). The AC mains supply shall be fitted with a fuse or circuit breaker and ground-fault protection. Important! Verify the power supply settings before applying power.
4 Move the brown wire on the ballast connection block to the position shown Figure 9. 5 Close the base before applying power. Black Brown 208 V / 60 Hz 230 V / 60 Hz 208 V / 50 Hz 230 V / 50 Hz 245 V / 50 Hz Figure 9: Magnetic ballast connections Power connection Important! Connect the MAC 2000 Profile II directly to AC power. Do not connect it to a dimmer system; doing so may damage the fixture. You may need to install a cord cap that fits your supply on the power cable.
DATA Important! Never connect more than 1 data input and 1 data output. The MAC 2000 Profile II has both 3-pin and 5-pin XLR sockets for DMX input and output. The pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5. The sockets are wired in parallel: both inputs connect to both outputs.
RIGGING 6 25 256 25 6 256 The MAC 2000 Profile II can be placed on stage or clamped to a truss in any orientation. The Fast-Lock system enables quick and easy fastening of the clamp brackets in 4 positions as shown Figure 10. Figure 10: Clamp bracket positions Warning! Always use 2 clamps to rig the fixture. Lock each clamp with both 1/4-turn fasteners. The fasteners are locked only when turned fully clockwise. Attach an approved safety cable to the attachment hole in the base.
CONTROL PANEL The LED control panel is used to set the address and personalities, read lamp hours and other information, calibrate effects, and run a test routine. Most of these functions may be performed remotely via the serial link with the Martin MP-2 Uploader. Navigation The DMX address and any messages (see page 34) are displayed when the MAC 2000 Profile II is turned on. To enter the menu, press [Menu]. Press [Up] and [Down] to move within the menu. To select a function or submenu, press [Enter].
If tracking mode movement is not satisfactory there are 2 parameters that can be adjusted. The first is selected under P E R S / T R A C / M O d E . The default, M O d 1 , is the best choice with controllers that calculate intermediate positions at a steady rate. Begin by selecting the alternative, MO d 2 , which is better if the intermediate positions stray significantly from the line of travel. The second parameter is the number of position updates used to calculate speed.
Firmware version IN FO / VE R displays the version number of the installed firmware. The firmware version is also displayed briefly at startup. DMX The D MX L menu shows the DMX start code (S T CO ) and DMX values received for each effect. Service messages The Service LED on the control panel lights under conditions that require fixture service, and there is a message describing the service required. To display the message, select S M S G in the main menu. This item is available only when the LED is lit.
Figure 12: Zoom calibration point 3 Pan calibration is most useful when multiple fixtures are stacked vertically. To calibrate, set zoom, focus, iris, and tilt position for easy one-over-the-other comparison and set each fixture to the same pan DMX value. Select one fixture to be the reference fixture. On the other fixtures, select U TI L /C A L/ P OF and press [Enter]. Adjust the offset as necessary to align the beam with the reference beam. Press [Enter] to save the setting.
OPTICAL CONFIGURATION Gobos Specifications All gobo slots including the seven color/gobo wheel positions accept round theatrical size-E glass gobos. Aluminum gobos are suitable for short-term use only. For best results, custom gobos should meet the following criteria. Outside diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37.5 +0/-0.3 mm (1 15/32 +0/-0.01 in.) Maximum image diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing rotating gobos Important! The gobo can fall out if the spring is inserted backwards. 1 Disconnect the fixture from power and allow it to cool. 2 See Figure 15. Lock the head in the upside down position and remove the bottom cover. Turn the gobo wheels as required to access the desired position. Pull the gobo holder away from the wheel slightly to release. Remove the gobo holder. 3 Remove the gobo retention spring from the gobo holder and drop the gobo out of the holder.
2 Lock the head in the upside down position and remove the bottom cover. Turn the color/gobo wheel as required to access the desired position. 3 To remove, press the filter or gobo from the lamp side to release it. Remove from wheel. 4 To insert, work the filter or gobo under the retention spring and position it between the pins. The long edge of the six-sided color filters must be precisely aligned with the inside of the hub in order to fit.
EFFECTS The MAC 2000 Profile II is compatible with USITT DMX512 controllers. The fixture has two DMX operating modes, 8-bit and 16-bit.16-bit mode requires four more DMX channels than 8-bit mode but provides more precise gobo indexing and pan/tilt positioning. All other functions are identical. The complete DMX protocol begins on page 24.
Effect wheel The effect wheel provides a variable frost filter and two rotating slots that house a beam shaper and a three-facet prism. The position and velocity of the rotating slots are selected on the effect wheel’s Position / Velocity Channel. Iris The iris closes down to 15 percent of its full-open diameter with high, 200-step resolution. The Iris Channel also provides random and variable speed pulsating iris effects. Focus and zoom The focus lens focusses the beam from approximately 2 meters (6.
ROUTINE MAINTENANCE The MAC 2000 Profile II requires routine cleaning. The schedule depends heavily on the operating environment; please consult a Martin service technician for recommendations. Refer all service not described here to a qualified Martin technician. Important! Excessive dust, smoke fluid, and particulate buildup degrades performance and causes overheating and damage to the fixture that is not covered by the warranty. Warning! Disconnect the fixture from power before removing any cover.
Software installation Software updates are installed in the MAC 2000 Profile II using a Martin MP-2 Uploader or a LightJockey 4064 DMX interface card. The procedure is found in the MP-2 user manual and the Martin Software Uploader online help file. Requirements The following are required in order to install software. • The MAC 2000 Profile II update file, available for download from the User Support Area of the Martin web site (http://www.martin.dk). • The Martin Software Uploader program, version 4.
DMX PROTOCOL DMX channel Start code = 0 8-bit 16-bit 1 1 If reset is disabled, i.e., d RE S =O F F, the command executes only when position 7 is selected on the color wheel and gobo 5 is selected on both gobo wheels. 2 If lamp off is disabled, i.e., dLOF =OFF, the command executes only when position 7 is selected on the color wheel and gobo 5 is selected on both gobo wheels.
DMX channel Start code = 0 8-bit 16-bit 7 Value Percent Function 0 - 20 20 - 40 40 - 60 60 - 80 80 - 100 100 - 120 120 - 140 140 - 160 0-7 7 - 16 16 - 23 23 - 31 31 - 39 39 - 47 47 - 55 55 - 63 Color/Gobo Wheel Continuous scroll White ! Position 1 Position 1 ! Position 2 Position 2 ! Position 3 Position 3 ! Position 4 Position 4 ! Position 5 Position 5 ! Position 6 Position 6 ! Position 7 Position 7 ! Open 160 - 163 164 - 167 168 - 171 172 - 175 176 - 179 180 - 183 184 - 187 188 - 191 63 - 64 64
DMX channel 8-bit Start code = 0 16-bit 9 9 - 10 10 Value Percent 0 - 255 0 - 100 Gobo Wheel 1, Position/Velocity Coarse Position (MSB), Min ! Max 0-2 3 - 127 128 - 252 253 - 255 0-1 1 - 50 50 - 98 99 - 100 Rotation velocity No rotation CCW, slow ! fast CW, fast ! slow No rotation 0 - 255 0 - 100 Gobo Wheel 1, Fine Position Fine Position (LSB), Min ! Max 0-9 0-3 10 - 14 15 - 19 20 - 24 25 - 29 30 - 34 3-5 5-7 7-9 9 - 11 11 - 13 Indexed gobo rotation Gobo 1 (Limbo Donut) Gobo 2 (Triangl
DMX channel 8-bit 12 13 Start code = 0 16-bit 15 16 15 17 16 18 17 19 - 20 18 21 - 22 20 Percent Function 0 1 - 175 176 - 183 184 - 191 192 - 199 200 - 207 208 - 215 0 1 - 68 69 - 72 72 - 75 75 - 78 78 - 81 81 - 84 Effect Wheel Selection and Macros Effect selection Open Variable frost, 0 ! 100% Effect 1, indexed rotation Set position / velocity Effect 2, indexed rotation on next channel.
CONTROL MENU Menu Item Options Notes (Default settings in bold print) A dd R - 1 - 51 2 DMX address 8b it Full control with coarse pan, tilt, and gobo indexing P SE T 16 bt Full control with fine pan, tilt, and gobo indexing ON Map DMX pan control to tilt channel and vice versa.
Menu Item Options Notes (Default settings in bold print) TO TL Total hours of operation since fabricated RS ET Hours of operation since counter reset. To reset, display counter and press [↑] for 5 seconds. TO TL Total hours of operation with lamp on since fabricated RS ET Lamp hours since counter reset. To reset, display counter and press [↑] for 5 seconds. TO TL Total number of lamp strikes since fabricated RS ET Number of lamp strikes since counter reset.
Menu Item Options Notes (Default settings in bold print) R ST - Reset fixture L ON - Lamp on L oF F - Lamp off OP EN Open shutter CL OS Close shutter ST RF Fast strobe ST RM Medium strobe ST RS Slow strobe d IM 0- 25 5 Dimmer C YA N, M AG ,Y E L 0- 25 5 C TC 0- 25 5 Color temperature correction. Cold →Warm (0-178 mireds) OP EN Color wheel in open position. C1 -C 7 Color wheel positions 1 →7.
Menu Item Options Notes (Default settings in bold print) OP EN Gobo wheel 2. Open position g1 I - g5 I Gobo wheel 2. Indexed gobos 1→5 g1 g - g5 R Gobo wheel 2. Rotating gobos 1→5 g1 IS - g5 IS Gobo wheel 2. Indexed gobo shake 1→5 g1 RS - g5 RS Gobo wheel 2. Rotating gobo shake 1→5 CW F Gobo wheel 2. Clockwise rotation - fast CC WF Gobo wheel 2. Counter clockwise rotation - fast CW M Gobo wheel 2. Clockwise rotation - medium CC WM Gobo wheel 2.
Menu Item Options Notes (Default settings in bold print) ON Enable pan/tilt position correction system OF F Disable pan/tilt feedback. Setting not saved.
ADJUSTMENT SUBMENU This menu is located under UT IL / Ad j .
DISPLAY MESSAGES Message Appears when... RS T ( Reset) ... the fixture is indexing effects at startup. Wait for reset to complete. SR ST (Serial reset) ... the fixture has received a reset command from the controller. Wait for reset to complete. Set PERS/dRES to off to prevent accidental reset commands. HO ME ... the effects have been indexed and are moving to their default positions. Wait a few moments. OP EN ...the lamp access cover is not fully closed.
TROUBLESHOOTING Problem One or more of the fixtures is completely dead. Fixtures reset correctly but respond erratically or not at all to the controller. Magnetically indexed effect resets correctly but wanders after fixture reaches operating temperature. Mechanical effect loses position. No light and “LERR” error message displayed. Probable cause(s) Remedy No power to fixture. Check that power is switched on and cables are plugged in. Primary fuse blown (located near mains inlet).
CIRCUIT 36 BOARD CONNECTIONS MAC 2000 Profile II
SPECIFICATIONS MAC 2000 PROFILE II Note that versions with electronic ballast are denoted with an ‘E’. PHYSICAL Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 mm (16.0 in) Width: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490 mm (19.3 in) Height: . . . . . . . . . . . . . . . . . . . . . . . .
MAXIMUM POWER AND CURRENT - ELECTRONIC BALLAST 100 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1590 W, 19.8 A 100 V / 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1560 W, 19.3 A 120 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
