2D Wireless Ring Barcode Scanner Quick Guide For full user’s manual, please contact your local distributor.
FCC WARNING STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
BEEPER INDICATION INTRODUCTION Micro USB port LED Indicator Function Button/ Power Button (with Protective Cover) Restart Button (insert pin into the hole) Exit Window Touch-Activated Trigger Button Velcro Strap SPECIFICATIONS Sensor Resolution Indicator PCS Housing Profile Battery Life Charge Time Radio Coverage Symbologies Area Image Sensor 5mil/ 0.1mm (1D), 6.67mil/ 0.2mm (2D) LED, Buzzer 40% Plastic(PC+ABS) BT HID, BT SPP, USB HID, USB VCP, Memory 4500 scans (1 scan/ 5 sec) 2.
OUT OF THE BOX CHARGING THE BATTERY Host Scanner USB A Wireless Ring Barcode Scanner USB Charger Cable 2D Wireless Ring 1 Barcode Scanner 2 Quick Guide Quick Guide Micro USB 1. Flip open the micro USB port on the scanner. 2. Insert the micro USB connector into the port on the scanner and USB A connector into a USB port on the host PC. 3. Keep charging until the red LED indicator turns off.
STEP 1 - GETTING STARTED 1. Pull open the long end and insert your index finger through the loop. 3. Clench your fist and use your thumb to tap the touch-activated trigger button. A gentle touch on the button will work; there is no need to press with force. 2. Adjust and attach the long end for a comfortable fit. 4. Aim at the barcode you wish to scan.
STEP 3 - INTERFACE SELECTION ATTENTION 1. If either your hand or the Velcro strap is soaking wet, the Laser beam may automatically light up without touch trigger. The scanner can still work well in this condition but it will waste battery power, so it is recommended to dry both your hand and the Velcro strap. 2.
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E043$ *.E043$* [ Recommended ] BT mode - HID 1. Press power button to activate the scanner. 2. Scan [DISCONNECT] 3. Scan [BT mode - HID]; the scanner will emit several beeps. 4. Select “Wireless Scanner” from discovered device list. 5. If Bluetooth application requests for a pincode, see next page PINCODE SETUP , otherwise please skip this step. 6. The scanner will beep twice to verify the connection. . E042$ *.
NUMERIC BARCODES *1* *2* *3* *4* *5* - 13 - 1 6 2 7 3 8 4 9 5 0 *6* *7* *8* *9* *0* - 14 -
POWER OFF TIMEOUT SMARTPHONE/TABLET TOUCH KEYBOARD The period of inactivity before auto power-off. Please follow below instruction to toggle touch keyboard on smartphone/tablet. Variable Timeout . B030$ *.B030$* *.B029$* SET MINUTE (Range: 00 ~ 60) iOS To toggle iOS touch keyboard, please simply press the function button. . B029$ SET SECOND (Range: 00 ~ 59) The default timeout is 00 minute and 30 seconds. For example, to set the timeout as 5 minutes 30 seconds: 1. Scan [Set Minute] 2.
GENERAL SETTINGS TERMINATOR . D012$ . A001$ DEFAULT CR . D011$ . P023$ ABORT LF . D013$ . A007$ CHECK VERSION CR + LF . D010$ BEEPER NONE . F019$ *.F019$* . D015$ BEEP ON SPACE . F012$ .
KEYBOARD LAYOUT . C009$ . C010$ ENGLISH (USA) JAPAN (106 key) ENGLISH (UK) CANADIAN (FRENCH) FRENCH CANADIAN (TRADITIONAL) . C018$ . C025$ . C034$ . C012$ . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
KEYBOARD LAYOUT . C030$ . C017$ CZECH (QWERTY) BELGIAN (AZERTY) . C028$ . C022$ CZECH (QWERTZ) DUTCH . C027$ . C021$ HUNGARIAN (QWERTZ) DANISH . C032$ . C024$ HUNGARIAN (101 KEY) SLOVAK . C033$ . C016$ SWISS (GERMAN) BRAZILIAN (PORTUGUESE) . C023$ .
ENABLE SYMBOLOGIES MEMORY MODE . A002$ ENABLE ALL CODE . C035$ MEMORY MODE *.c035$* After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: < Date >, < Time >, < Barcode Data > < CR > . G036$ *.G036$* ENABLE ALL 1D CODE To retrieve stored data, please connect the scanner to the host with cable, access removable storage device “MiniScan” from which you may open or copy the file “BARCODE.txt” to your computer.
MEMORY MODE DATE & TIME SETUP MEMORY MODE DATA FORMAT . R011$ . R006$ *.R006$* SET DATE Example: To set Date to 2017-08-01 (Year-Month-Day): 1. Scan [Set Date] 2. Scan [1], [7], [0], [8], [0], [1] on page 13 & 14. 3. Scan [Set Date] DATA FORMAT *.R011$* The default Data Format is ,
MEMORY MODE DATE FORMAT MEMORY MODE . R008$ *.R008$* TIME FORMAT . R009$ DATE FORMAT TIME FORMAT *.
HOW TO REMOVE VELCRO STRAP 1. Pull open the long end. 3. Pull open the short end on the other side. 2. Pull out the long end through the slot. 4. Remove the whole Velcro strap from the scanner by pulling the long end.
HOW TO INSTALL VELCRO STRAP 1. Insert the short end through the slot, with Velcro side facing upwards. 3. Insert the long end through the other slot, with Velcro side facing upwards. 2. Attach the short end to the long end to close. 4. Attach the long end to itself to close.
TEST BARCODES TEST BARCODES QR Code Code 39 Micro QR Code CODE-39 TEST Interleaved 2 of 5 PDF417 9876543210 Code 128 12345678 Data Matrix Aztec EAN 4 716415 942052 - 33 - - 34 -
