OPERATIONS MANUAL MODEL: MIX59000D 3 1/2 CU. FT. SCAN TO WATCH ASSEMBLY VIDEO 104 S. 8th Ave. Marshalltown, IA Phone 800-888-0127 / 641-753-0127 Fax 800-477-6341 / 641-753-6341 www.marshalltown.
INTRODUCTION The Gilson Wheelbarrow mixer is great for the do-it-yourself home project. It allows you to work almost anywhere. The mixer will clear a 30” door and easily fits into an elevator. A quiet 115-volt motor allows you to work indoors without emissions. The exclusive in-mold helix drum gives a better homogenous mix. The lifting action picks material up from the base of the drum. Used in the mixing of concrete, plaster, adhesives, overlays, chemicals, seed, and grain – the options are endless.
1. SAFETY PRECAUTIONS The following precautions are suggested to help prevent accidents. Before operating this equipment read all precautions. Equipment should be operated by trained individuals. If the safety instructions and warnings are not read and carefully followed, personal injury could occur. • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Keep hands and clothing away from any moving parts while the mixer is running.
Part # Description MIX59000D-01 GEAR PLASTIC GUARD-ABS MIX59000D-02 HEX FLANG NUT-#M8 MIX59000D-03 HEX FLANG BOLT-#M8 MIX59000D-04 MIX59000D-05 Qty Part # Description Qty 1 MIX59000D-25 HEX SOCKET SCREW-#M8x8 1 10 MIX59000D-26 GEAR SHAFT FASTEN SLEEVE-#45 C 1 8 MIX59000D-27 HEX BOLT-#M10x25 4 BELT PLASTIC GUARD-ABS 1 MIX59000D-28 LOCK WASHER-#D10 4 PLAIN HEAD PIN-#6x20 1 MIX59000D-29 HEX NUT-#M10 4 MIX59000D-06 GEAR SHAFT-#45-C.
ASSEMBLY GUIDE FRAME ASSEMBLY 1. Lay out the frame parts. 2. Assemble the tires on the axle. (# 40 & # 41) 3. Assemble tires and axle to the frame.
FRAME ASSEMBLY CONTINUED 4. Attach the axle to the frame. 5. Assemble the supporting pipe. (Using # 39, # 42, # 43 and # 45) 6. Assemble the drum support frame.
FRAME ASSEMBLY CONTINUED 7. Fasten all the bolts and nuts. MOTOR ASSEMBLY 1. Assemble the motor onto the frame. (Using # 2 and # 3) NOTE: Assemble the drive pulley (# 30) on the motor shaft (If Not Preassembled) 2. Assemble the pinion gear shaft driven pulley to gear sleeve assembly and attach shaft sleeve (# 14).
MOTOR ASSEMBLY CONTINUED 3. Assemble the V-Belt on the pulleys NOTE: Adjust belt tension and keep pulleys parallel. Tension can be adjusted by sliding motor and/or pinion gear sleeve. Tighten bolts when you have enough tension. 4. Attach the belt guard on the frame. (Using # 2 and # 3) 5. Attach the gear guard on the frame.
DRUM ASSEMBLY 1. Lay out the drum components. 2. Assemble the central paddle (#16) and its Pad (#17) in the drum. 3. Assemble the gear wheel (#19) to bottom of the drum. NOTE: Make sure raised side of gear is facing away from drum. 4. Bolt the drum plate assembly, pad and gear to drum (Using # 15 and # 20). NOTE: We recommend applying siliconoe to #15 bolt head to ensure a proper seal.
DRUM ASSEMBLY CONTINUED 5. Put the washer (#21) on the gear shaft. 6. Assemble the drum onto the frame. 7. Check that gears are aligned and interlocked. INCORRECT Adjust by loosening pulley gear.
DRUM ASSEMBLY CONTINUED 8. Assemble the shaft positioning sleeve (#26) on the gear shaft. 9. Assemble the handle (#34) on the frame. 10. Insert the handle fixing spring clip on the handle. 11. Attach the plastic handle cover.
HOW TO MIX CONCRETE Wheelbarrow Mixer - Model MIX59000D You’ll need approximately 1 ¼ gallons of water. 1 – 80 lb. Bag of pre-mix concrete 1. Start Mixer 2. Put in 1 gallon of water 3. Add ½ of 80 lb. Bag of pre-mix concrete – mixture will be very sloppy 4. Slowly add 2nd half bag of concrete 5. Add ¼ gallon of water slowly to obtain desired thickness. How to mix Sand & Gravel Wheelbarrow Mixer - Model 59000D You’ll need a square point shovel Portland cement, gravel or round stone and masonry sand. 1.
MIXERS ONE-YEAR WARRANTY This product is warranted to the original purchaser only, to be free of defects in material and workmanship under normal use, for one year from purchase date. MARSHALLTOWN Company shall without charge for parts and labor, repair or replace such parts which are found to be defective. All transportation charges for replacement parts must be borne by the purchaser.
HOW TO OBTAIN PARTS AND SERVICE INFORMATION For parts and service information, contact either your local dealer or the MARSHALLTOWN Company: 104 S 8 Ave Marshalltown, IA 50158 Phone: (641) 753-0127 Fax: (641) 753-9227 HOW TO ORDER PARTS When ordering parts, be sure to indicate the following information: • • • • • Name of each part Complete part number Quantity of each part Model Name (Include all letters and numbers) Serial Number (Include all letters and numbers)
of 16
04/2012R1
