Marshall Electronics Broadcast A/V Division Model No. VS-PTC-200 Compact Camera Controller Operating Instructions ver.
Table of Contents Chapter 1. Safety Instructions ......................................................................... 2 Precautions............................................................................................ 3 FCC Warning ......................................................................................... 3 EN55022 (CE Radiation) Warning......................................................... 3 Chapter 2. About The Product....................................................
Chapter 1. Safety Instructions Always follow these safety instructions when setting up and using the VS-PTC-200 Camera Controller: 1. Use attachments only as recommended. 2. Use the type of power source indicated on the Camera Controller. If you are not sure of the type of power available, consult your distributor or local electricity company for advice. 3. Always take the following precautions when handling the plug. Failure to do so may result in sparks or fire.
Precautions Warning: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. If Camera Controller will not be used for an extended time, unplug it from the power socket. Note Risk of Electric Shock DO NOT OPEN Caution: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to licensed service personnel.
Chapter 2. About The Product 2.1 Introduction The VS-PTC-200 Compact Camera Controller is a full-function system keyboard. With features of ergonomic design, multi-function, high reliability and easy operation, it is a perfect controller for rugged PTZ cameras, video conference cameras, surveillance cameras and so on. 2.
2.4 Parts and view 1 0~9 (Numbers) 7 Input numbers. 2 3 SETUP (Enter setup menu) 9 MIRROR (flip the image) Press MIRROR key to control the image flip of the camera 5 LOCK (keyboard lock) Press LOCK key to lock the control keyboard and key in the user password to unlock the keyboard. 10 POWER (Power switch) Press POWER key to turn on / off the camera. 11 ESC (Exit / Delete) It is a key to EXIT in a menu or DELETE in other operations.
Joystick 14 5 This joystick is used to Pan, Tilt, Zoom and Focus Non-Menu State: U Left/Right/Up/Down: Pan/Tilt the camera correspondingly Twist clockwise: Zoom In, Twist anti-clockwise: Zoom Out; Press Zoom/ Focus Switch Key and Twist: Focus Near/Far Press BRT+ key to turn up the image brightness. 16 Menu State: 6 Zoom / Focus Switch Key This key is used to switch between zoom and focus function.
2.5 Connections 2.5.
2.5.2 RS-422 Pins instructions Pin No. function 1 GND 2 RXD IN- 3 RXD IN+ 4 TXD IN- 5 TXD IN+ 2.5.3 RS232 Pins instructions 8 Pin No.
Chapter 3. Setting Menu *** Press [SETUP] on the remote control to enter the setting menu; the bold underlined values in the following table are defaults. 1st Level Major Items 2nd Level Minor Items Camera ID Protocol Camera Setting Time Setting Time Display 9 3rd Level Adjustment Values 1~ C ~255 Set camera ID VISCA only works with ID 1~7 V V：VISCA，ID 1~7 U U PD ： PELCO D ， ID PD Baud Rate 1. 9600 2.
Sleep Setting - Pin Setting - Joystick Calib U U Pan Left - Pan Right - Tilt Up - Tilt Down - Zoom Tele - Zoom Wide - Free State Save - 10 Off 60m 30m 10m 5m 1m 30s User Admin 1. 2. 3. 4. 5. 6. 7. 1. 2. U Cancel U Speed Setting - 1. High 2. Middle 3. Low Default Setting - 1. Yes 2. No Information - U U - Set sleep time of the controller.
Chapter 4. Menu Operation After powered on, “USER PIN” will show on the controller’s screen. The initial pin is “111111”. Pin Error： When “USER PIN：ERROR” shows on screen, it indicates wrong pin was input. Enter correct pin to get to next step Pin Correct： Screen shows “ 1” camera icon and default camera number. If there is no further operation for long time, screen will display current time automatically. If still no operations, the controller will enter sleeping mode. Enter OSD menu Press SETUP key.
5. Address Setting. Input number to set camera address (range from 1~7). Press ENT to confirm. 6. After the camera setting is finished, the system will automatically return to the main menu. 4.2 Time Setting Set time in 24 hour format. 1. Move the joystick up/ down, choose ”TIME SETTING”. 2. Right move the joystick or press ENT to get into time setting menu, “H” hour becomes editable, input digits from keypad or move joystick up / down to set the “H” (range: 0~23).
2. Right move the joystick or press ENT to enter “BACKLIGHT MODE”. Move the joystick up/ down to select backlight options. Right move the joystick or press ENT to confirm. 4.5 Sleep Setting Set sleep time of the controller. In non-menu status, the screen will enter the sleep mode if no operation is performed for a programmable period. 1. Move the joystick up/ down, select “ SLEEP SETING”. 2. Right move the joystick or press ENT to enter “ SLEEP SETTING” . Move the joystick up/ down to select sleep time.
During these operations, press key ESC to exit the PIN setting menu. 4.7 Joystick Calibration After long-time use, the joystick may require calibration. 1. Move the joystick up/ down, select “JOYSTICK CALIB”. 2. Right move the joystick or press ENT to confirm, enter the “JOYSTICK CALIB” menu. “PAN LEFT” will be displayed, move the joystick to the left limit and hold, then press ENT to finish “PAN LEFT” calibration. It will enter next menu. 3.
4.9 Default Setting Restore the keyboard setting to factory default. 1. Move the joystick up/ down, choose "DEFAULT SETTING". 2. Right the joystick or press ENT key, enter "DEFAULT SETTING" menu, move the joystick left/ right, select options" NO", press ENT to confirm. Marshall Electronics, Inc. 1910 East Maple Ave. El Segundo, CA 90245 Tel: (800) 800-6608 • (310) 333-0606 Fax: 310-333-0688 www.LCDracks.com support@marshall-usa.
