Specifications

6
Operational Setup
1. Unpack the V-R104DP-HD and accompanying V-PS12-5V-XLR power supply. Physically inspect for any damage that may have
occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608.
If you are not located within the continental United States call [phone].
2. After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is required when
installed to prevent possible damage to the V-R104DP-HD internal components.
3. Connect required cables for signal input and output. Please note that power must be applied to the V-R104DP-HD for all outputs
to be activated. All BNC connectors should be rated for 75Ω.
4. Plug the V-PS12-5V-XLR power supply into the A.C. source
5. Attach twist lock power connection from V-PS12-5V-XLR power supply to the back of the unit.
6. Turn on each of the V-R104DP-HD screens by depressing the power switch located on the front of the unit for each screen.
7
Connectors
* HDSDI/SDI Inputs comply to SMPTE - 259M, 292M, SDI - 270Mbs, HDSDI - 1.485Gb/s
* Component Inputs comply to SMPTE274M, 294M,295M,296M
* Composite Video Inputs comply to SMPTE-170M
* Tally lamps active when connected to ground
S-VideoIn
4PinDin(Female)
Pin1-GND
Pin2-GND
Pin3-Yin
Pin4-Cin
S-VideoOut
4PinDin(Female)
Pin1-GND
Pin2-GND
Pin3-Yout
Pin4-Cout
ActiveOutputsrequirepowertobeapplied
Allinputsignalsappearasoutputsignal
Analogoutputsignalsarebufferedandamplified
VGA/XGA Connector
PIN#
SIGNAL
PIN#
SIGNAL
1
RED
9
NC
2
GREEN
10
NC
3
BLUE
11
NC
4
NC
12
NC
5
GND
13
HSYNC
6
RED SHIELD
14
VSYNC
7
GREEN SHIELD
15
NC
8
BLUE SHIELD
DVI-I Connector
Pin#
Signal
Pin#
Signal
1
T.M.D.S DATA 2-
16
HOT PLUG DETECT
2
T.M.D.S DATA 2+
17
T.M.D.S DATA 0-
3
T.M.D.S DATA 2/4
SHIELD
18
T.M.D.S DATA 0+
4
T.M.D.S DATA 4-
19
T.M.D.S DATA 0/5
SHIELD
5
T.M.D.S DATA 4+
20
T.M.D.S DATA 5-
6
DDC CLOCK
21
T.M.D.S DATA 5+
7
DDC DATA
22
T.M.D.S CLOCK
SHIELD
8
ANALOG VERT. SYNC
23
T.M.D.S CLOCK+
9
T.M.D.S DATA 1-
24
T.M.D.S CLOCK-
10
T.M.D.S DATA 1+
11
T.M.D.S DATA 1/3
SHIELD
C1
ANALOG RED
12
T.M.D.S DATA 3-
C2
ANALOG GREEN
13
T.M.D.S DATA 3+
C3
ANALOG BLUE
14
+5V POWER
C4
ANALOG HORZ SYNC
15
GND
C5
ANALOG GROUND
Dimensions 19.12” w x 8.67” h x 1.5” d (485.7mm x 220.22mm x 38.1mm)
V-R104DP-HDWeight 5.5 lbs (2.4 kg)
V-PS12-5V-XLRPowerSupplyWeight 1 lbs (0.45kg)
5
Mechanical Specifications
3
8
V-R82DP-HD Users Guide
Marshall Electronics
DryEraseLabel
Screenaspectratioswitch4:3or16:9selectorandindicators
4:3Aspect16:9Aspect
10
Switch Settings, Adjustments and Indicators
TallyLamps
V-R104DP-HD Users Guide
Marshall Electronics
ImageAdjustmentControls
Note:TintonlyfunctionswhenNTSC
VideoorS-Videoareselected
Pin1-Green
Pin2-Red
Pin3-Yellow
Pin4-Gnd
Pin5-Gnd
Pin6-
Pin7-
TallyIN
DB-15Female
12VDCfrom
V-PS12-5V-XLR
powersupply