User Manual

Power Button with Indicator
Press power switch to turn on the power the unit and indicator lights will turn on. Press again to turn off
the power.
Tri-Color Tally Light
30mm Tri-Color tally lamp controlled via the Remote connector on the rear of the unit.
User-Denable Function Keys
Eleven user-denable function buttons can be used for direct access to various settings. Functions are as-
signed using the on-screen menu
User-Dened Rotary Encoders
Four Rotary Encoders may be assigned their function thru the User Assign menu. The Standard modes are;
• User 1 Brightness
• User 2 Contrast
• User 3 Saturation
• User 4 Sharpness
When pressed, the LED will illuminate, turning the encoder will allow the user to make adjustments to the
selected value. When pressed again, the LED will turn OFF and the value will return to the preset level.
MENU and Volume Control Buttons
Press the Center MENU Button to access the on-screen Menu, Press the UP-é, Down-ê, Left-ç, or
Right-è Buttons to navigate the on-screen menu and change values. Press the Center Menu Button to
save any changes or selections. Exit the on-screen menu by pressing the Left-ç Button one or more times.
When not in the Menu mode, the Left-ç, or Right-è Buttons control the Headphone Volume directly.
Headphone Jack
¼” and 3.5mm stereo headphone jacks. Left and Right source are selected from the on-screen menu and
are the same as for the built in speakers. Level for both headphone jacks are controlled via the left/right
menu keys when not in menu mode. (Use of headphones will not mute front speakers.)
Front Speakers Controls
The top knob controls the volume of the front speakers. The center knob adjusts the balance between left
and right front speakers. The push button at the bottom mutes the front speakers only. When muted the led
indicator turns RED
• Insertion of a headphone plug into either the ¼” or 3.5mm headphone jacks will not mute the front speakers.
• The Front speakers are not affected by the Audio Mute command found in the Function Preset menu.
1
2
3
4
5
6
Front Panel Features
6
1
4
56 3
2
7
7
Rear Panel Features
Parallel Remote
RJ-45 Pin
Assignments
Pin 1
GPI 1
Pin 2
GPI 2
Pin 3
GPI 3
Pin 4
GPI 4
Pin 5
GND
Pin 6
GPI 5
Pin 7
GPI 6
Pin 8
GPI 7
1
6
2
7
3
4
7
8
GPI Input
RJ-45 connector for 7 user-assignable GPI inputs. Assignable using the on-screen menu.
Service Port
Proprietary connection used for rmware upgrades and LCD color balance calibration.
(Optional OR-SM Service Module Required)
Power Input
Connect 12VDC to the 4-Pin XLR power input connector. Power can be supplied from the included power
supply, or from a variety of DC sources supplying at least 1 Amp at 12 Volts.
IMPORTANT: If using a power source other than the included power supply be sure that the polarity of
the DC input is correct:
Pin 1: GND / Pin 2: N/C / Pin 3: N/C / Pin 4: +12VDC
Option Slot
Used to connect an optional input card such as the OR-DVI (DVI input) or OR-YPR (Component input).
Audio Output
3.5mm stereo Un-Balanced -10 dBu line level output for monitoring imbedded audio channels. The desired
audio channels are selected in the Audio on screen menu. The output level is also controlled thru the Audio
on screen menu.
Video input Connectors
Dual Auto-Sensing HDSDI BNC Video Inputs There are two HDSDI video inputs, each are video input
auto detects HD and SD SDI video signals.
Video Output Connector
The output connector is an active re-clocked video signal from the Selected HDSDI input.
Balanced Audio Output Connectors
3 Pin Male XLR connectors for Left / Right +4dBu Line output to feed external ampliers or other profes-
sional processing equipment.
1
2
3
4
6
5
7
8
5