Marshall Electronics Broadcast Division Model No. M-LYNX-702W Dual 7” High Resolution Rack Mount Display with Waveform Operating Instructions V 2.
Marshall Electronics Table of Contents 1. Product Description......................................................... 3 2. Menu Settings.................................................................. 6 3. Specifications................................................................... 11 4. Included Accessories....................................................... 11 5. Troubleshooting................................................................ 11 6. PC Set Monitor Configuration Application......
M-LYNX-702W / Product Description 1. PRODUCT DESCRIPTION FRONT PANEL FEATURES 1 2 3 4 5 6 7 1. Rackmount ears with tilt capability 2. Handle 3. Headphone jack. Accepts standard 3.5mm mini-phone plug. 4. POWER button (Lights red in standby mode; green when operating). 5. INPUT select button cycles through HDMI, SDI, YPbPr and Video. 6. F1~F4 user-defined function buttons (lighted when selected).
Marshall Electronics BACK PANEL FEATURES 1 Note: 2 3 4 5 6 7 8 9 Each screen has its own full complement of video input connections. Power, TALLY and LAN connections go to both screens 1. 4-pin Power Connector 4-pin XLR DC power input compatible with typical broadcast television camera 12-volt power supplies. Caution: Some 4-pin power supplies provide 24 volts. These are NOT compatible with this monitor. Please check the label on the power supply before connecting.
M-LYNX-702W / Product Description 3. Barrel Power Connector 12V DC power input barrel connector. Plug the supplied DC power adapter here. (Center pin is +) Important: Please connect only one type of power supply at a time to this monitor. 4. Analog Audio “RCA” Connectors Audio left and right inputs. These audio inputs are active whenever Video or YPbPr are selected as the video sources. This audio may be monitored at the Headphone jack. 5.
Marshall Electronics 2. MENU SETTINGS Press MENU knob on the monitor and function menus will pop-up on the screen. Rotate left or right to select an option. Then press the knob again to open the selection. When an arrow pointer appears in the menu, turn the Menu knob again to access the item or to confirm a selection. 1. PICTURE This page provides controls for typical picture adjustments.
M-LYNX-702W / Menu Settings Marker Enable – this is the master control to turn all markers on or off. Center Marker – places a “+” mark in the exact center of the display. (Useful for checking camera or graphics positioning.) Aspect Marker – places borders on screen representing various typical video and cinema aspect ratios. This does not change the displayed aspect ratio. That setting is in the Video menu.
Marshall Electronics 4. CAMERA AUX & AUDIO This page offers settings to assist with camera setup, focus and exposure adjustments. Audio metering can be set here as well.
M-LYNX-702W / Menu Settings YCbCr – a graphic representation of the Luminance plus the color components in the video signal. Useful for equipment adjustment and confirming proper operation. RGB – a graphic representation of the three primary color components of video picture. Useful for making equipment adjustments. Vector – a graphic representation of the colors in a picture. Brightness levels are not shown. The vector display is used with color charts or test signals.
Marshall Electronics Backlight – adjusts the brightness of the LCD backlight. This is different from the “Brightness” control. Backlight is adjusted to compensate for room lighting without upsetting Contrast and Brightness adjustments. Reset – sets all menu items back to the way the unit ships from the factory. OSD – adjusts the position of the on-screen display messages and menus. The amount of time menus remain on screen can also be adjusted.
M-LYNX-702W / Specifications 3. SPECIFICATIONS Panel Size Panel Resolution Brightness Contrast Viewing Angle Input Voltage Input Signal Power Consumption Operating Temperature Storage Temperature Dimension W/H/D Weight 7 inch x 2 1280 × 800 pixels 400 cd/m2 800: 1 178° / 178°(H/V) DC 12V HDMI, SDI, YPbPr & Video ≤24W -200C~600C -300C~700C 19” x 5” x 1” (482.5×132×25mm) 5.8lbs (2.65Kg) 4. INCLUDED ACCESSORIES 1. DC 12V Power adapter 2. CD with remote operation application 3. Operations Manual 5.
Marshall Electronics 6. PC Set Monitor Configuration Application PCSet is a convenient software tool for controlling multiple Marshall M-LYNX-702W dual-screen monitors from a single computer. PCSet will run on any Windows-based computer (XP or later) and does not have to be installed. Simply copy the file PCSet.exe to the desktop or some other convenient location, double-click and the control screen will appear. You can download PC Set Monitor Configuration Application with instructions here: http://www.
