CV620-BK4/WH4 Full-HD PTZ Camera Installation Guide Ver 1.
Table of Contents Safety Instructions ............................................................................................ 4 Package Contents ............................................................................................. 6 Product Overview .............................................................................................. 7 3.1 Overview............................................................................................. 7 3.2 Description of LED indicator.........
6.13 I would like to change the camera direction ..................................... 31 6.14 I would like to display the current status........................................... 31 6.15 I would like to reset to the original setting ........................................ 31 DIP Switch Setting........................................................................................... 32 7.1 DIP Switch ........................................................................................ 32 7.
Page intentionally left blank 3
Safety Instructions Always follow these safety instructions when setting up and using the Camera: 1. Use attachments only as recommended. 2. Use the type of power source indicated on the Camera. If you are not sure of the type of power available, consult your distributor or local electricity company for advice. 3. Always take the following precautions when handling the plug. Failure to do so may result in sparks or fire: Ensure the plug is free of dust before inserting it into a socket.
Precautions Warning: To reduce the risk of fire or electric shock, do not expose this camera to rain or moisture. If Camera will not be used for an extended time, unplug it from the power socket. Note Risk of Electric Shock Please do not open it by yourself. Caution: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to licensed service personnel.
Chapter 2 Package Contents CV620-BK4/WH4 Instructions for installation Remote Control Power Cord Power Adapter RS-422 Connector Metal Plate B M3 Screws Appearance may vary depending on country/region Metal Plate A 6
Chapter 3 Product Overview 3.1 Overview Front View Rear View 1. Camera Lens 2. Power LED Indicator 3. Standby LED Indicator 4. 3G-SDI Output 5. Power Input 6. RS-422 Connection 7. RS-232 Output 8. RS-232 Input 9. DVI Output 10.OUTPUT Switch 11.IR SELECT 3.2 Description of LED indicator 3.2.1 Power烉 3.2.1.1 No Light: Power off 3.2.1.2 Green light: In use 3.2.1.3 Flickering green: Signal from the remote control is received; the indicator flickers every 0.5 seconds 3.2.2 Standby烉 3.2.2.
Instruction for Installation 4.1 Preparation before installation Installation and connection of the Camera requires special skills. To install by yourself, please follow necessary steps, ensure steady and tight installation of the device, and pay attention to your safety to avoid any accident. 4.1.1 Ensure the safety of the installation environment. Please do not install this device on an unstable ceiling or in a place where the device is in danger of falling to avoid any accident. 4.1.
4.2.1.2 Installation steps 1. Please adjust DIP switch at first prior to installation *Please refer to Chapter 7 DIP Switch Setting for the relevant descriptions on DIP switch. 2. Place the camera on a flat desk directly to ensure the normal vertical and horizontal operation of the machine 4.2.2 I would like to install CV620-BK4/WH4 on the ceiling 4.2.2.1 Prepare for the parts and equipment required during the installation 1.
4.2.2.3 Max.
4.2.2.4 Size Diagram 1.
2.
3.
4.2.2.5 Precautions for installation 1. Before installation, please confirm the orientation of the machine relative to the object to be captured. 2. It is recommended that the machine should be set at a distance of more than 1 meter away from the object to be captured. Please adjust for a best distance according to the magnification of the lens. 1 meterЌ 3. The machine (including metal plates) is weighed at about 2.5 kg.
3. Lock the metal plate B on ceiling mounted hanger ɈCaution: (1) Please use the hanger that has obtained UL security approval (2) Please reserve the hole for the connecting wires of the camera 4.
4.2.2.7 How to remove 1. Remove the connecting wires from the camera 2. Uninstall the camera together with the ceiling, loosen the three screws that fix the metal plates A and B and push to the left to remove the machine 3.
4.3 Connecting the device 4.3.1 Image Output 4.3.1.1 Connecting to a HDTV / computer monitor (DVI) DVI cable Monitor or HDTV 4.3.1.
4.3.2 Controlling CV620-BK4/WH4s with the computer 4.3.2.1 Connecting to one computer for connection between CV620-BK4/WH4s (RS-232 in/out) * With RS-232 in/out, at most 7 CVs can be connected. 4.3.2.2 Connecting to one computer for connection between CV620-BK4/WH4s (RS-422) *Please refer to 7.2 RS-422 connection for the RS-422 connection instructions. *With RS-422, at most 7 CVs can be connected.
Chapter 5 Remote Control and Setting Menu 5.1 Functions of remote control * The below functions are listed alphabetically.
5.2 Setting Menu *Press [Menu] on the remote control to enter the setting menu; the bold underlined values in the following table are defaults. 1st Level Major Items 2nd Level Minor Items 3rd Level Adjustment Values Function Descriptions 1. Full Auto 2. Shutter Pri Mode 3. Iris Pri Exposure mode setting 4. Manual 5. White Board Exposure Comp. On / Off Exposure Comp.
Iris Priority 1/120 1/120 1/100 1/100 1/90 1/75 1/60 1/50 1/30 1/25 1/15 1/12 1/8 1/6 1/4 1/3 1/2 1/2 1/1 1/1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. F1.6 F2 F2.2 F2.7 F3.2 F3.8 F4.5 F5.4 F6.3 F7.
Manual Gain Manual Speed 1. 0dB 2. 2 dB 3. 4 dB 4. 6 dB 5. 8 dB 6. 10 dB 7. 12 dB 8. 14 dB 9. 16 dB 10. 18 dB 11. 20 dB 12. 22 dB 13. 24 dB 14. 26 dB 15. 28 dB 16.
Manual Iris Gain Limit 1/60 1/50 1/30 1/25 1/15 1/12 1/8 1/6 1/4 1/3 1/2 1/2 1/1 1/1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. F1.6 F2 F2.2 F2.7 F3.2 F3.8 F4.5 F5.4 F6.3 F7.8 F9 F11 F13 F16 F18 8 dB 10 dB 12 dB 14 dB 16 dB 18 dB 20 dB 22 dB 24 dB 26 dB 28 dB 30dB Manually set the iris The maximum electric gain limit.
Iris Limit WDR Anti Flicker Mode White Balance One Push Trigger Manual Red 1. 2. 3. 4. 5. 6. 7. 8. 1. 2. 3. 4. 5. 6. F1.6 F2.2 F3.2 F4.5 F6.3 F9 F13 F18 Off 1 2 3 4 5 1. 50Hz 2. 60Hz 1. Off 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Auto Indoor Outdoor One Push WB ATW Sodium Lamp Manual 3000K 4300K 5000K 6500K 8300K WideAuto Max. limit value of iris Set WDR Set the image sync frequency during capturing Select the color temperature mode 1. 4000k ~ 7000k 2. 3200k 3. 5800k 4. 1700k ~ 10000k 5.
Manual Blue 0~ C~60 Adjustable when the white balance mode is set to Manual Picture effect 1. Off 2. Neg 3. B & W Set the picture effect Sharpness 1~A~16 2D NR 3D NR Picture Image Mode Image Mode Load 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6.
Gamma 0~ A ~3 Skin Tone 1~ A ~5 Brightness 0~ A ~14 Contrast 0~ A ~14 Black Level 1. 2. 3. 4.
D-Effect PTZ Speed Comp On / Off D-Zoom Limit Set the Pan/Tilt Moving speed subject to the zoom position x1~x12 Limit the D-zoom multiple Mirror AF Sensitivity 1. LOW 2. Middle 3. High AF Frame Full Frame/ Center Video Type SDI DVI-I Prompt On / Off IR Receive On / Off Language English / Chinese Control Device Encoder / Controller Motionless Preset On / Off Protocol Protocol V / Protocol PD Auto Focus System Off Mirror Flip Mirror + Flip 1. 2. 3. 4.
Status PD Address 1~ C~255 Camera Address 0~7 Output Mode 1. 1920x1080/60p 2. 1920x1080/50p 3. 1920x1080/30p 4. 1920x1080/25p 5. 1920x1080/60i 6. 1920x1080/50i 7. 1280x720/60p 8. 1280x720/50p 9. 1280x720/30p 10. 1280x720/25p 11. 1080/59.94p 12. 1080/59.94i 13. 1080/29.97p 14. 720/59.94p 15. 720/29.
Chapter 6 Descriptions of Major Functions 6.1 I would like to switch to CV620-BK4/WH4 1. Press [Camera 1 ~ 3] on the remote control to select CV620-BK4/WH4. Camera 1 ~ 3 is selected with IR SELECT. 6.2 I would like to save the current lens position data 1. Hold [Preset + ID] on the remote control to save the current position data. ID shall be a digit [0 ~ 9]. Use VISCA Command to save the position data to [0 ~ 127]. 6.3 I would like to clear the saved position data 1.
2. 3. 4. 5. 6. 7. Press [f] or [e] to select [System]. Press [ENTER] to activate. Press [c] or [d] to select [Motionless Preset]. Press [ENTER] to activate. Press [f] or [e] to select [Off / On]. Press [MENU] to exit. 6.7 I would like to zoom in/out images 6.7.1 Adjust image size 6.7.2 Fine-tune image size 1. Press [Fast +] on the remote control to zoom in images. 2. Press [Fast -] on the remote control to zoom out images. 1. Press [Slow +] on the remote control to zoom in images. 2.
6. Press [f] or [e] to select [High / Middle / Low]. 7. Press [MENU] to exit. 6.10 I would like to set the image mode 1. Press [Picture] on the remote control to switch [Off / Neg / B&W]. 6.11 I would like to freeze images 1. Press [Freeze] on the remote control to freeze the current image on the display. 6.12 I would like to rotate the image 1. Press [Mirror] on the remote control to switch [Off / Mirror / Flip / Mirror + Flip]. 6.13 I would like to change the camera direction 1.
Chapter 7 DIP switch setting * Please turn off the machine before changing DIP switch setting. 7.1 DIP Switch 7.1.1 OUTPUT Switch Setting 0 1 2 3 4 5 6 7 8 9 A B C D E F Function Descriptions 1920x1080/60p 1920x1080/50p 1920x1080/30p 1920x1080/25p 1920x1080/60i 1920x1080/50i 1280x720/60p 1280x720/50p 1280x720/30p 1280x720/25p 1080/59.94p 1080/59.94i 1080/29.97p 720/59.94p 720/29.97p Reserved 7.1.
7.2 RS-422 Connection 7.2.1 RS-422 Pin Description Pin NO. 1 2 3 4 5 6 7 8 9 Function RXD OUT RXD OUT + TXD OUT TXD OUT + GND RXD IN RXD IN + TXD IN TXD IN + *For SONY products, please connect IN+ to OUT+ For non-SONY products, it may be necessary to connect IN+ to OUT- 7.2.2 Use RS-422 Connection 1. Hold the two sides of RS-422 connector and pull out in the direction shown by the arrow in the figure below 2. Peel off a section of copper wire (AWG Nos.
3. Insert the wired RS-422 connector back to the camera. Now the connection is completed * When RS-422 connection is being used, do not use RS-232C connection.
Chapter 8 Troubleshooting This chapter describes problems you may encounter while using the CV620-BK4/WH4. If you have questions, please refer to related chapters and follow all suggested solutions. If the problem still occurs, please contact your distributor or service center. No. 1. Problems Boot without Solutions Make sure you have plugged in the power cord. power signal 2. There is no image 1. Check the power. output from 2. Check if DIP switch is properly set.
screen are as far away from each other? as possible in order to avoid interference. 4. When several CV620-BK4/WH4s are connected in the same area, the operation of two remote controls at the same time may result in signal interference. It is recommended to use only one remote control. 6. The device cannot be controlled with Codec 7. The device cannot be controlled with RS-232/RS-422 1. Please consult the distributor to make sure the firmware version is the latest one.
