Owner`s manual

ULTIMATE SERIES CONTROLS
MARQUIS SPAS • RELAXING YOUR WORLD 53
PUMP PRIMING (Pr)
Pump priming feature begins at start-up. When spa is energized, the LCD panel will display
a Pr message. This mode will last approximately fo ur to five minutes if not exited
manually. See THERAPY PUMP(S) section.
UNDERWATER AND ENTRYWAY LIGHTS
The pad marked LIGHT ON/OFF turns the underwater and Entryway lights on and off.
The low-voltage system produces a night light for evening use and makes entering and exiting
the spa safer. After being on for one hour, the lights will automatically turn off.
SOAK TIMER AND SOAK FEATURE
Pressing the SOAK TIMER pad will turn the jet pump to low-speed and s tart a 59-
minute timer. The timer will display the elapsed time in one-minute increments (1-14).
After 15 minutes, the display will flash the
minute (15-59) for ten seconds before
switching to a steady display as a safety reminder to not overstay your soak. During the
Soak Timer mode, the temperature display can be checked by pressing the TEMP SET
pad. A second press of the SOAK TIMER pad will turn off all functions (except light) for 30
minutes, if left uninterrupted, for an all-quiet soak. Pressing any pad will cancel the Soak
mode.
PROGRAMMABLE FILTER TIMES
To adjust the filter time: First press the FILTER CYCLE pad for display mode, then
press the FILTER CYCLE pad to scroll through filtration time options and adjust for
desired filtration time FC1 (90 minutes), FC3 (three hours), FC6 (six hours) or FC9
(nine hours) and enter the selection using the TEMP SET pad.
Display now shows e ither 2C (two filter cycles per day), 1Cd (one cycle per day
that will start one munute
after power up) or 1Cn (one cycle per day that will start
12 hours after power up). Press FILTER CYCLE pad to scroll through theselections
and press TEMP SET pad to enter.
The display will now show either SL4 (four hour cycle), SL3 (three hour cycle), SL2
(two hours cycle, SL1 (one hour cycle) or SL0 (Smart cycle off). Press the FILTER
CYCLE pad to scroll through the selections and then press the TEMP SET pad to
set and exit the programming mode.
Factory default settings for the above selections: Filtration time F3 (three ho urs);
Filter cycles 2C (two times per day); Cleanup cycle Smart Logic 4H (four hours).
The filter cycle will begin six minutes after the spa is energized. If you select two cycles per
24 hours, the second cycle will begin 12 hours after the first cycle. Also, at the start of the
first filter cycle, auxiliary pump will
run on low-speed for five minutes. The primary pump
will run on high-speed for five minutes, then low-speed for the cycles duration.
CONSTANT CLEAN
Automated
Filtration
System
SOAK
TIMER
LIGHT
ON/OFF
Soak Timer: 1st press turns pump
to low-speed and starts 59-
minute timer; 2nd
press “all quiet”
mode
Temp Set: Temperature displayed
on LCD; Press repeatedly to
increase temperature; Pause;
Repeat to decrease temperature
Heat On:
Illuminates when
heat is on
Filter Cycle: 1st press
selects Filter Cycle mode; 2nd
press chooses cycle FC1,3,6,9;
3rd press Temp Set pad to
choose cycles per 24 hours 1C-
2C; 4th press Filter Cycle to
adjust; 5th press Temp Set to
select and exit program
LCD Display:
Shows temperature,
Maintenance Reminders
Light On/Off: 1st press turns underwater
and Entryway lights on; 2nd
press turns lights off
System Lock: Press System
Lock then immediately press
Temp Set to activate lock.
Repeat to unlock system
Heat Mode:
Standard, Economy or Sleep
modes show on LCD display
FILTER
CYCLE
HEAT
MODE
SYSTEM
LOCK
TEMP
SET
CL: Clean Filter
CH: Change Water
MAINTENANCE
REMINDERS
Heat On
ULTIMAT E SERIES
100°F
TRI-ZONE THERAPY SYSTEM
Secured
!