Owner`s manual
COASTAL SERIES CONTROLS
CONSTANT CLEAN
Automated
Filtration
System
LIGHT
ON/OFF
MARQUIS SPAS • RELAXING YOUR WORLD 43
Soak Timer: 1st press turns pump
to low-speed and starts 59-
minute timer; 2nd
press “all
quiet”
mode
Heat On:
Illuminates when
heat is on
LCD Display:
Shows temperature,
Maintenance Reminders
Light On/Off: 1st press turns
underwater and Entryway
lights on; 2nd press
turns lights off
Filter Cycle:
1st press selects
Filter Cycle mode; 2nd
press chooses cycle FC1,3,6,9;
3rd press Temp Set chooses
cycles per day 1C-2C; 4th
press Filter Cycle adjusts; 5th
press Temp Set selects and
exits program
System Lock: Press System
Lock then immediately press
Temp Set to activate lock.
Repeat to unlock system
Heat Mode:
Standard, Economy
or Sleep modes show on
LCD display
Temp Set: Temperature is
displayed on LCD: Press repeatedly
to increase temperature; Pause;
Repeat to decrease temperature
FILTER
CYCLE
HEAT
MODE
SOAK
TIMER
SYSTEM
LOCK
TEMP
SET
CL: Clean Filter
CH: Change Water
MAINTENANCE
REMINDERS
Heat On
COASTAL SERIES
100°F
DUAL-ZONE THERAPY SYSTEM
Secured
!
PUMP PRIMING (Pr)
Pump priming feature begins at start-up. When spa is energized, the LCD panel will display
a Pr message. This mode will last approximately fo ur to five minutes if not exited
manually. See THERAPY PUMP(S) section.
UNDERWATER AND ENTRYWAY LIGHTS
The pad marked LIGHT ON/OFF turns the underwater and Entryway lights on and off.
The low-voltage system produces a night light for evening use and makes entering and exiting
the
spa safer. After being on for one hour, the lights will automatically turn off.
SOAK TIMER AND SOAK FEATURE
Pressing the SOAK TIMER pad will turn the jet pump to low-speed and s tart a 59-
minute timer. The timer will display the elapsed time in one-minute increments (1-14).
After 15 minutes, the display will flash the minute (15-59) for ten seconds before
switching to a steady display as a safety reminder to not overstay your soak. During the
Soak Timer mode, the temperature display can be checked by pressing the
TEMP SET
pad. A second press of the SOAK TIMER pad will turn off all functions (except light) for 30
minutes, if left uninterrupted, for an all-quiet soak. Pressing any pad will cancel the Soak
mode.
PROGRAMMABLE FILTER TIMES
To adjust the filter time: First press the FILTER CYCLE pad for display mode, then
press the FILTER CYCLE pad to scroll through filtration time options and adjust for
desired filtration time FC1 (90 minutes), FC3 (three hours), FC6 (six hours) or FC9
(nine hours) and enter the selection using the TEMP SET pad.
Display now shows e ither 2C (two filter cycles per day), 1Cd (one cycle per day
that will start one munute after power up) or 1Cn (one cycle per day that will start
12 hours after power up). Press FILTER CYCLE pad to scroll through theselections
and press TEMP SET pad to enter.
The display will now show either SL4 (four hour cycle), SL3 (three hour cycle), SL2
(two hours cycle, SL1 (one hour cycle) or SL0 (Smart cycle off). Press the FILTER
CYCLE pad to scroll through the selections and then press the TEMP SET pad to
set and exit the programming mode.
Factory default settings for the above selections: Filtration time F3 (three ho urs); Filter
cycles 2C (two times per day); Cleanup cycle Smart Logic 4H (four hours).
The filter cycle will begin six minutes after the spa is energized. If you select two cycles
per 24 hours, the second cycle will begin 12 hours after the first cycle. Also, at the start
of the first filter cycle, auxiliary pump will run on low-speed for five minutes. The primary
pump will run on high-speed for five minutes, then low-speed for the cycles duration.