owner’s manual WELCOME TO THE SPA LIFE! Please enjoy your new Marquis spa, but think safety first. Read your Owner’s Manual in its entirety before installing your spa and encourage all spa users to do the same. More than just common sense, this Owner’s Manual provides vital safety and operational information. CARE AND ENJOYMENT GUIDE A Care and Enjoyment guide is located in the back of the manual.
product reference SERIAL NUMBER LOCATION You will find the serial number on the Underwriters Laboratories tag in the equipment area.
owner’s manual index IMPORTANT SAFETY INSTRUCTIONS 120V, Cord Connected Models ....................................................... 4 240V, Permanently Installed or Converted Models ....................... 5 All Spa Models .................................................................................. 5-7 Personal Safety ................................................................................. 8-9 INSTALLATION INSTRUCTIONS Location ..............................................................
safety instructions The following instructions are required to be printed by Underwriters Laboratories (UL) as a condition of the listing of this product. They contain important safety information. We strongly encourage you to read and apply them. IMPORTANT SAFETY INSTRUCTIONS WHEN INSTALLING AND USING THIS ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: 1. READ AND FOLLOW ALL INSTRUCTIONS 2.
safety instructions 240 VOLT, PERMANENTLY INSTALLED OR CONVERTED MODELS 9. A ground terminal is provided on the terminal block (TB-1, terminal 7) located inside the control box. To reduce the risk of electric shock, connect this terminal to the grounding terminal of your electrical service or supply panel with a continuous green, insulated copper wire. The wire must be equivalent in size to the circuit conductors supplying the equipment.
safety instructions • Persons using medications should consult a physician before using a spa since some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation. 15.DANGER: TO REDUCE THE RISK OF INJURY TO PERSONS. Do not remove the suction fittings. 16.DANGER: RISK OF INJURY: Never operate a spa if the suction guard(s) is broken or missing. Never replace a suction guard with one rated less than the flow rate marked on the original suction guard.
safety instructions SAFETY INSTRUCTIONS FOR FRENCH SPEAKING SPA OWNERS AVERTISSEMENT: Ne pas placer d’appareil électrique (luminaire, téléphone,radio, téléviseur, etc.) moins de 1.52 m de cette cuve de relaxation. AVERTISSEMENT: Ne pas laisser les enfants utiliser une cuve de relaxation sans surveillance. AVERTISSEMENT: Pour éviter que les cheveux ou une partie du corps puissent être aspirés, ne pas utiliser une cuve de relaxation si les grilles de prise d’aspiration ne sont pas toutes en place.
safety instructions PERSONAL SAFETY Prolonged immersion in hot water can result in HYPERTHERMIA, a dangerous condition which occurs when the internal temperature of the body reaches a level above normal (98.6°F, 37°C). The symptoms of hyperthermia include dizziness, fainting, drowsiness, lethargy, and a body temperature above 98.6°F (37°C).
safety instructions PERSONAL SAFETY DOs: • Be sure your spa is connected to the power supply correctly – only use a licensed electrical contractor. • Shut off power supply (unplug 120V models) before draining the spa or servicing the electrical components. • Test the Ground Fault Circuit Interrupter (GFCI) monthly. • Always test the water temperature with an accurate thermometer before entering the spa to be sure that it’s a safe temperature. • Remember that wet surfaces can be very slippery.
installation instructions LOCATION For your portable spa to function properly and safely, it must be located on a hard, flat, level surface. Inground spas require special installation techniques and should be planned in conjunction with your spa dealer. Improper installation can result in structural damage to the spa and the voiding of your spa warranty.
installation instructions OUTDOOR AND PATIO INSTALLATION To install the spa outdoors, we recommend a reinforced concrete pad at least four inches thick. The reinforcing material should be attached to a #8 AWG bonding wire per national and local electrical code. If you place the spa on the ground, even temporarily, place concrete pavers under the entire bottom of the spa. The concrete pavers should be a least two inches thick and level across the entire surface.
installation instructions SHUT-OFF VALVES Your spa is equipped with shut-off valves (see EQUIPMENT DIAGRAM) that shut off the water flow to the equipment system for dealer service. At times, a new spa or one that has recently been serviced, may have the shut-off valves partially closed which can restrict the water flow and hinder jet performance. Be sure the valves are fully open.
installation instructions SUCTION GUARDS The suction guard(s) in the footwell of your spa is an opening through which the jet pump(s) draws water. Suction fittings are equipped with a safety guard. Suction through the fittings can be strong. The safety guard(s) must remain in place and undamaged. A fitting with a damaged guard(s) can be dangerous, especially to small children or people with long hair. Should any part of the body become drawn to a fitting, turn the jet pump(s) off immediately.
installation instructions tion. All 240V units require four wires (line 1, line 2, neutral, and ground). Refer to the label at the terminal block. NOTE: Ensure the GFCI is properly installed. Failure to do so may result in spa malfunction or damage which is not warranted. A pressure wire connector is located on the exterior of the control box. This pressure wire connector should be bonded with at least #8 AWG (8.
starting your spa START-UP PROCEDURE Your spa is equipped with solid-state Comfort Controls specific to your spa model. Please see SPA CONTROL OPERATION for your specific spa model. To start your spa, you need a spa water test kit and an underwater thermometer. It is important to follow each of these steps when starting your spa.
starting your spa Start-up procedure (continued) Vent air by slightly opening pump unions. Use TEMP pad to set water temperature. 6. Turn the power on. 7. Your spa is now in “pump priming” mode and a “Pr” message displays in the LCD window of the control panel. While in this mode the spa appears idle, which lasts approximately four to five minutes if not exited manually. To exit manually, press the TEMP pad. 8. At this time the spa should have water flowing from the jets.
operating your spa HYDRO KINETIC THERAPY™ SYSTEM HK™8 NECK JETS The neck jets are turned on and off (when the jet pump is on) using the small teardrop neck jet control lever. HK™40 Jet HK™12 JET This small jet provides a targeted stream of water. HK™16 JET The direction of water flow can be changed by redirecting the central nozzle. The water flow can be adjusted by turning the jet face using the four tabs.