Certificate

ManualsBrandsMARQUARDT ManualsPush Actuated Switches & ButtonsPushbutton 400 Vac 16 A 1 x Off/(On) IP40 momentary 1 pc(s)

(h) - These switches are DPTT switches

Note 1 - This switch has been investigated for use only as a voltage selector.

Note 10 - The switch employes quick-connect terminals. They have been evaluated for use with solid and/or solder dipped stranded

conductors, No. 10 AWG.

Note 2 - For Cat. Nos. 1830 and 1835, the suitability of the steel spring as a current-

carrying part in the pilot light portion of the switch, shall

be determined in the end-use.

Note 3 - The reversing switch has not been evaluated and should be investigated for compliance with the end-use product standard.

Note 4 - The quick-

connect terminals have been investigated with a suitable female connector attached to No. 12 AWG wire. The suitability of

non-Recognized connector or other size wire shall be determined in the end-use application.

Note 5 - This switch is to be used with Marquardt switches Cat. No. 1293 (rated 6 A-125 V ac, 1/6 hp-125 V ac), Cat. No. 1297 (rated 6 A-

125 V ac, 1/4 hp-125 V ac, 5 A-250 V ac, 1/2 hp-250 V ac) and Lucerne switches, Cat No. TRM256 (rated 6 A-125 V ac), Cat No. TSCR-256

(rated 6 A-125 V ac). They each employ a built-in interlock at the trigger to prevent making and breaking current.

Note 6 - The screw-down wire binding terminals have not been investigated. The suitability of these terminals shall be determined in the end-

use application.

Note 7 - The supply source of the bulb circuit was not evaluated during the investigation of the switch. The suitability of this feature shall be

determined in the end-use application.

Note 8 - The performance of the remote actuated version (suffix RMTE) is dependent upon the combination of (1) the length of the extension

rod and (2) the distance between the Recognized Component Switch and the remote actuator button. The suitability of this combination

should be determined in the end product.

Note A - The switches are not considered relampable.

Note B - Type 1703.3402; Each pole has a special rating: 1st pole 5A 110-250Vac, 2nd pole 0.3A 15Vdc, 3rd pole 5A 110-250Vac, 4th pole

20A 15Vdc

* - CTI PLC is marked on individual board.

Marking: Markings on the switch body consist of at least items (a) and (b) or (c) as noted below (other markings shall be on the smallest

shipping package):

(a) Manufacturer's identifier (such as name or trademark , , ,

, as described in the UL file)

(b) Electrical ratings

(d) Factory code (as described in the UL Report, if more than one location)

(e) Recognized Component Mark,

The appearance of a company's name or product in this database does not in itself assure that products so identified have been

manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under

UL's Follow-Up Service. Always look for the Mark on the product.

UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide

Information, Designs and/or Listings (files) must be presented in their entirety and in a non-misleading manner, without any manipulation of

the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories

Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following

Last Updated on 2009-02-04

Questions? Notice of Disclaimer Page Top

Seite

von

WOYR2.E41791

Switches, Special Use

Component

29.04.2009

http://database.ul.com/cgi

bin/XYV/template/LISEXT/1FRAME/showpage.html?name=WOYR

...