VECTOR CROSS TRAINER User Manual and Safety Procedures Marpo Kinetics Inc., 258 LINDBERGH Ave, Livermore, CA. 94551 • 925-606-6919 tel. •877-275-1005 fax • All rights reserved Disclaimer: MARPO KINETICS makes no representations or warranties regarding the contents of this manual. We reserve the right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such revisions or changes. Marpo Kinetics, Inc.
Table Of Contents 1. Using your Marpo Kinetics VECTOR CROSS TRAINER .............................................. 1 2. Safety Information ............................................................................................................ 1 Safety Information........................................................................................................................ 1 Maintain Labels and Nameplates........................................................................................
STOP It is very important that you read these Maintenance and Safety Procedures before operating the Product. Remember to perform the periodic maintenance requirements specified in these Maintenance and Safety Procedures to assure proper operation and your continued satisfaction. MAXIMUM USER WEIGHT: 350 LB (160 KG). Marpo Kinetics, Inc.
1. USING YOUR MARPO KINETICS VECTOR CROSS TRAINER First time users: 1. Set rope speed to level 1. Since handle is spring loaded, always hold it firmly when changing speeds. 2. Sit on seat. 3. Grasp the rope with both hands and SLOWLY start pulling the rope. 4. Always perform the exercise in a slow, controlled manner and breathe normally. Rope speed Selector Light headedness and dizziness can be signs of over-exertion or other medical conditions.
9. Use the machine only for the intended use. Obtain instruction and DO NOT modify the machine(s). Maintain Labels and Nameplates Do not remove labels for any reason. They contain important information. If unreadable or missing, contact MARPO KINETICS for a replacement. Securing Equipment All MARPO KINETICS equipment must be secured to the floor to stabilize and eliminate rocking or tipping. This must be performed by a licensed contractor.
• Make sure that all users are properly trained on how to use the MARPO KINETICS equipment. • Make sure that there is enough room for safe access and operation of the MARPO KINETICS equipment. • Use only MARPO KINETICS supplied components to maintain/repair the MARPO KINETICS equipment. UNDERSTANDING ALL WARNINGS TO THE FULLEST IS IMPORTANT. IF ANY OF THESE WARNINGS ARE UNCLEAR, CONTACT MARPO KINETICS PERSONNEL FOR CLARIFICATION.
Product Maintenance and Use Repair of any MARPO KINETICS equipment should be performed only by authorized persons. Never modify any MARPO KINETICS equipment or attempt to make adjustment(s) to, or the repair, of any MARPO KINETICS equipment without first contacting MARPO KINETICS. Always notify someone authorized to make such repair. Instruct users to report any equipment or training irregularities to supervisory personnel immediately. 4.
sand the repair can be attempted. This process is a difficult one and should be practiced by someone knowledgeable in this field. Upholstery Maintenance Due to corrosive agents in perspiration, upholstery should be cleaned daily with a 10% diluted consistency of lanolin hand cleaner in warm water. Do not use products such as Lysol®, Armor Alll®, Windex® or other abrasive detergents as they will dry out and eventually cause Naugahyde® to prematurely crack.
Note: Use polishing compound (such as car wax) to clean and remove scuffs from powdercoated surfaces as necessary. Important Reminders • DO NOT use abrasive or highly alkaline cleaners on the plastic or rubber components, or on the rope. • Never scrape plastic components with razor blades or other sharp instruments. • Benzene, gasoline, acetone or carbon tetrachloride should never be used on the plastic or rubber components, or on the rope.
environment, rust or corrosion as a result of the Product(s) location, alterations or modifications without our written authorization or by failure on your part to use, operate and maintain the Product as set out in this document. Parts and Service You will receive information on how to get a replacement part, arrange for service where your Product is located or advise you on how and where to ship the Product for service.
