TM13 TM13 USER MANUAL 20590_20131113 TM13 ™ ALL RIGHTS RESERVED MARMITEK ©
TABLE OF CONTENTS TABLE OF CONTENTS .......................................................... 2 SAFETY WARNINGS ............................................................. 3 HOW DOES MARMITEK X-10 WORK? ................................. 4 ADRESSES ......................................................................... 4 SIGNAL RANGE .................................................................. 5 INTRODUCTION .................................................................... 7 How does it work? .
SAFETY WARNINGS The wiring of your electrical installation is live (230 V) and extremely dangerous. Never connect the module when plugged into the mains. Always turn off the main switch before starting the installation. This product is for professional use and should be installed by a certified installer." To prevent short circuits, this product should only be used inside and only in dry spaces. Do not expose the components to rain or moisture.
HOW DOES MARMITEK X-10 WORK? Marmitek X-10 components use the existing mains wiring to communicate (using Marmitek X-10 signals). You can build a complete system using the three different kind of components of the Marmitek X-10 System: 1. Modules: These components will receive Marmitek X-10 signals and will switch or dim the attached lamp or appliance. Examples of these modules are lamp modules and appliance modules. These are available as build-in, micro, DIN rail and plug-in modules. 2.
SIGNAL RANGE Range of Marmitek X-10 signals over the Power Line and how to increase the range. The Marmitek X-10 System is based on power line communication. The range of the Marmitek X-10 signals very much depends on the local circumstances. On average the range is a cable length of 80 meters. If you have difficulties with the range of your Marmitek X10 signals, please pay attention to the following facts: 1.
Old Televisions Copiers Fluorescent Lights Gas Discharge Lamps (Energy Saving Lamps) 3. Some (old) devices are able to disturb the signal by transmitting noise on the power line. Because the Marmitek X10 signals are transmitted on 120 kHz, only noise on or near this frequency will have influence on the range. When you use a FM10 Filter to connect this device to the power line, the noise will be filtered. 4.
INTRODUCTION Congratulations with your purchase of the Marmitek X-10 HOME CONTROL TM13 Transceiver. Among other things, the TM13 Transceiver allows you to use your Marmitek X-10 remote control to operate your X-10 switching and dimming modules, wherever you are in your house. How does it work? The TM13 is a controller that is activated by transmitters. The controller operates Marmitek X-10 modules via the mains to switch your lighting and appliances on and off.
• The MS13 wireless motion sensor with memory (switches lighting and appliances on when someone is present and switches them off again afterwards. Switches on interior and exterior lighting when arriving home in the dark.
FIRST USE OF THE TM13 1. 2. 3. 4. Set the HouseCode (A to P) of the Home Control TM13 Transceiver to the same code as you have set your other modules. The UnitCode cannot be set and will always be ‘1’. If the TM13 is set to HouseCode ‘P’, all commands from remote controls will be converted into an X-10 signal over the mains, regardless of the HouseCode. The HouseCode used will in this case be the same as the HouseCode of the remote control. Point the antenna upwards.
FREQENTLY ASKED QUESTIONS What is the reason for modules to switch on/off spontaneously? It is possible that a Marmitek X-10 System is installed at one of your neighbours using the same House Code. To solve this problem try to change the House Code of your system, or have FD10 Phase Coupler/Filter installed at your incoming mains. My modules will not respond to my controller. Make sure that the House Code on all Modules and Controllers are set to the same House Code (A .. P).
TECHNICAL DATA Supply voltage: Power consumption: Switching capacity: Frequency: Transmission signal: Signal sensitivity: X-10 Key codes: Input impedance: Ambient temperature: Dimensions: 230 V – 50 Hz < 20 mA, capacitive 300W/230V for light bulbs and lowvoltage halogen lamps with a 500W/230V transformer for inductive / capacitive loads 1200 W/230V for linear loads 433.92 MHz 120 kHz ± 2 kHz / 2.
DECLARATION OF CONFORMITY Hereby, Marmitek BV, declares that this TM13 is in compliance with the essential requirements and other relevant provisions of the following Directives: Directive 2004/108/ec of the european parliament and of the council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to
