Specifications

Email your order to us at [e-mail]
20
IR Distribution
Adaptors for the IR Distribution Amplifiers
Useful adaptors for the IRBKIT, Cat5Blasters
& IR Commander Matrix.
3.5mm Stereo Jack to Phono Plug
3.5mm stereo jack plug to
a single phono plug wired
middle of phono to tip of
jack and ground to ground
(making the jack mono) for
connecting IR receivers &
wands to the C5B system.
Code
KLD81 length 1m £3.99
IR Link Cable (3.5mm - 3.5mm Tip & Ring Only)
This cable allows you to take the IR wand output from
products such as the the CAT5 AV Distribution Amplifier
or CAT5QC Active and feed it
directly into the IR receiver
input on the IRBKIT or IR
Commander.
Code
KLDE6M length 1.5m £5.99
3.5mm Plug To CAT5 Socket
A short (25cm) line adaptor
with an RJ45 line socket to a
3.5mm stereo jack plug.
Supplied in pairs, for use with
the Keene IRCM and IRBKIT,
allowing wands and receivers
to be easily extended using
standard CAT5 cables.
Code
KA175 per pair £5.99
3.5mm stereo plug to plug to stereo
socket extension
For extending the IR wand & receiver cables
(normally 1.2m).
Code
KLD40 length 3.0m £4.49
Code KLD405 length 5.0m £4.99
Code KLD4010 length 10.0m £8.99
HDBaseT HDMI Distribution
The Aavara PE3D4K100A is a fantastic tool for sending
HDMI over long distances. Using just a single wire it can
be easily retrofitted within an existing network. HDBaseT
technology allows this system to send HDMI further and
at higher quality than all other conventional HDMI over
CAT5 solutions. With no compression and no loss of
quality you can get crystal clear 3D 1080p with 7.1
channel audio, and also have IR control, RS232 and
extend your 100Mbps LAN all over the one cable!
Over one single run of CAT5 cable you can:
• send uncompressed full HD 3D HDMI with 7.1ch audio
• remotely power the receiver
• IR control the source from the receiver
• RS232 control the source from the receiver
• use the 3 port hub in the sender & receiver to
extend your LAN
It also fully supports HDMI v1.4, allowing smooth 3D
video transmission from 3D Blu-ray players to 3DTVs,
with fully HDCP compliance. Built-in 3 x 100Mbps Fast
Ethernet RJ-45 ports at both sender and receiver allow
Internet connected withTV, Video device and PC, keeps
link with Internet.
PUMA HDMI V1.4 O Ver Single CAT6 HDBaseT Lite Kit
The PU-513L allows uncompressed HDMI, IR and RS-232
signals to be transmitted over a Single CAT5e/6 cable to
distances of up to 60m.
• HDMI 1.4 with 3D, 4K×2K support, HDCP and DVI
compliant
• Supports HDMI 1.4 (including HDCP) over a single
CAT5e/6 up to 60m
• Complies with HDBaseT™- Lite specifications
• Full HD resolution support (1080p@60Hz/36-bit), 3D
over 60m, 4Kx2K over 40m and PC resolution support
(VGA to WUXGA) over CAT5e/6 cable
• HDMI input up to 15m with 8-bit deep colour, or
10m with 12-bit deep colour
• Supports HDMI output up to 15m with 8/12-bit deep
colour
• Supports IR and RS-232 Control
• Supports High Definition LPCM 7.1CH, Dolby
TrueHD, Dolby Digital Plus and DTS-HD Master Audio
transmission
Code
PE3D4K100A £574.18
Code PU513L £244.22