0
1 P REFACE Thank you for purchasing the Marmitek Wireless* Pan-Tilt** MPEG4/MJPEG*** Network Camera, a powerful dual-codec*** wireless* network camera with the 1-way**** or 2-way***** audio function that provides the high-quality image and on-the-spot audio via the Internet connection. The Infrared LEDs and light sensor *****enable the camera to capture images even in the dark environment. The camera’s pan/tilt** functions allow you to control the camera to monitor everywhere remotely.
Chapter 3 Accessing the Camera lets you start using your camera without problem. The camera can be set up easily and work within your network environment instantly. Chapter 4 Configuring the Camera guides you through the configuration of the camera using the Web browser on your PC. Chapter 5 Appendix provides the specification of the camera and some useful information for using your camera. NOTE The illustrations and configuration values in this guide are for reference only.
2 C ONTENTS 0 ................................................................................ 0 1 Preface ..................................................................... 1 2 Contents .................................................................... 3 3 SAFETY WARNINGS ................................................... 4 CHAPTER 1 ......................................................................... 5 INTRODUCTION TO YOUR CAMERA ............................................ 5 1.
3 SAFETY WARNINGS o To prevent short circuits, this product should only be used inside and only in dry spaces. Do not expose the components to rain or moisture. Do not use the product close to a bath, swimming pool etc. o Do not expose the components of your systems to extremely high temperatures or bright light sources. o In case of improper usage or if you have altered and repaired the product yourself, all guarantees expire.
C HAPTER 1 I NTRODUCTION TO Y OUR C AMERA 1.1 Checking the Package Contents Check the items contained in the package carefully. You should have the following: 5 5 5 5 5 5 5 5 One Network Camera. One AC Power Adapter. One External Antenna.* One Wall Mount Kit. One GPIO Connector** One Ethernet Cable (RJ-45 type). One Installation CD-ROM. One Quick Installation Guide. NOTE Once any item contained is damaged or missing, contact the authorized dealer of your locale.
1.2 Getting to Know Your Camera Internal Microphone**** allows the camera to receive sound and voice. Power LED indicates the camera is powered on with the steady amber light. Link LED indicates the camera’s network connectivity with the flashing green light. Lens Assembly USB Port*** allows you to connect an external USB device. It provides the power distribution up to 500mA. USB*** Unmount Button Is used to remove the connected USB device safely.
Infrared LEDs (x7)***** allow your camera to capture clear image in a dark environment. Light Sensor ***** is used to trigger on and off the Infrared LEDs according the environmental light level. Antenna* Lens Assembly Power LED indicates the camera is powered on with the steady amber light. Link LED indicates the camera’s network connectivity with the flashing green light. Internal Microphone ***** allows the camera to receive sound and voice.
External Antenna* Screw Hole is used to connect the camera stand. DC Power Connector is used to connect the AC power adapter, in order to supply power to the camera. Reset Button will restart the camera when it is pressed quickly; when it is long pressed for five seconds, the camera will resume the factory default settings. Ethernet Cable Connector is used to connect the network cable, which supports the NWay protocol so that the camera can detect the network speed automatically.
Ethernet Cable Connector connects the network cable, which supports the NWay protocol so that the camera can detect the network speed automatically. External Antenna Connector* connects the external antenna. DC Power Connector connects the AC power adapter, in order to supply power to the camera. USB Unmount Button *** is used to remove the connected USB device safely. GPIO Connectors** is used to connect the external devices. Audio-out Connector***** connects an external active speaker.
Features and Benefits MPEG4/MJPEG Dual-codec Supported*** The Marmitek IP camera provides you with excellent images by the MPEG4/ MJPEG dual-codec selectable technology, allowing you to adjust image size and quality, and bit rate according to the networking environment. 1-way Audio Capability**** The built-in microphone of the Marmitek IP Eye Anywhere camera provides on-the-spot audio via the Internet, allowing you to monitor the on-site voice.
address of the camera)/mpeg4. Supports Multiple Profiles*** The camera supports multiple profiles simultaneously, so that you can separately set up different image settings (such as image quality and frame rate) for the three video types of the camera: MPEG4, MJPEG, and 3GPP. I/O Connectors Provided** The Marmitek IP RoboCam camera provides the I/O connectors on the rear panel (IN/OUT), which provide the physical interface to send and receive digital signals to a variety of external alarm devices.
banks, and more. The camera can capture both still images and video clips, so that you can keep the archives and restore them at any time. 1.4 System Requirement Networking LAN: 10Base-T Ethernet or 100Base-TX Fast Ethernet. WLAN*: IEEE 802.11b/g. Accessing the Camera using Web Browser Platform: Microsoft® Windows® 2000/XP/Vista/7 CPU: Intel Pentium III 800MHz or above RAM: 128MB****** 512MB*** Resolution: 800x600 or above User Interface: Microsoft® Internet Explorer 6.
C HAPTER 2 H ARDWARE I NSTALLATION 2.1 Kit Installing the Camera Stand, Wall Mount The Marmitek IP Eye Anywhere camera comes with a camera stand, which uses a swivel ball screw head to lock to the camera’s screw hole. When the camera stand is attached, you can place the camera anywhere by mounting the camera through the three screw holes located in the base of the camera stand.
The Marmitek IP RoboCam camera comes with a Wall Mount Kit, which allows you to place your camera anywhere by mounting the camera through the three screw holes located in the base of the Wall Mount Kit.
2.2 Connecting the Camera to LAN/WLAN Use the provided Ethernet cable to connect the camera to your local area network (LAN). When you connect the AC power adapter, the camera is powered on automatically. You can verify the power status from the Power LED on the front panel of the camera. Once connected, the Link LED starts flashing green light and the camera is on standby and ready for use now.
2.3 Applications of the Camera The camera can be applied in multiple applications, including: Monitor local and remote places and objects via Internet or Intranet. Capture still images and video clips remotely. Upload images or send email messages with the still images attached. The following diagram explains one of the typical applications for your camera and provides a basic example for installing the camera.
C HAPTER 3 A CCESSING T HE C AMERA 3.1 Using IPFinder The Marmitek IP camera comes with a conveniently utility, IPFinder, which is included in the Installation CD-ROM, allowing you to search the camera on your network easily. 1. Insert the Installation CD-ROM into your computer’s CD-ROM drive to initiate the Auto-Run program. 2. Click the IPFinder item to launch the utility. The control panel will appear as below. Display the connected camera(s). Double click to link the Camera.
3.2 Accessing to the Camera Whenever you want to access the Marmitek IP camera: 1. Connect your camera to the network (or the PC directly). 2. Since the default configuration of the camera is DHCP mode enabled, you are recommended to launch IPFinder to search the IP address that is assigned to the camera by the DHCP server, and then click Link to access the camera via the Web browser. 3.
page will appear as below: Live View/Setup Switch Zoom In Buttons Nightmode Button Camera Information Compression Buttons Pan/Tilt Buttons Live View Image Function Buttons The main page of the Web Configuration provides you with many useful information and functions, including: Camera Information – Displays the camera’s location and the current date & time. The information can be modified in the Web Configuration. Live View Image – Displays the real-time image of the connected camera.
where you clicked to display it in the central part of Live View area.** z When you enlarge the Live View by clicking the Zoom In buttons (2x or 3x), you can move the displayed image by right-clicking your mouse on the Live View area. The position where you right-clicked will be displayed in the central part of Live View area.** Zoom In Buttons – Click the buttons to zoom in the live view image by 1x, 2x, and 3x.
To set up the preset positions, move the camera lens by clicking the Left/Right/Up/Down buttons to the desired position first, then select the number (1~8) from the pulldown list and click the Apply button. You can enter a descriptive name for the assigned position in the text box to identify it easily. Function Buttons – Use these buttons to control the audio, video, and trigger functions. z Manual Record allows you to record and save a video clip.
4. Disable the ”Enable Protected Mode” then press OK 3.3 Configuring the IP Address of the PC If you failed to access to the camera, please check the IP address of your computer. When you connect the camera to your computer directly to proceed with configuration of the camera, you need to set up the IP addresses to be in the same segment for the two devices to communicate. 1. On your computer, click Start > Control Panel to open the Control Panel window. 2.
C HAPTER 4 C ONFIGURING T HE C AMERA 4.1 Using the Web Configuration You can access and manage the Marmitek IP camera through the Web browser and the provided software application UltraView. This chapter describes the Web Configuration, and guides you through the configuration of the camera by using the Web browser. To configure the camera, click Setup on the main page of Web Configuration. The Web Configuration will start from the Basic page.
The Web Configuration contains the settings that are required for the camera in the left menu bar, including Smart Wizard, Basic, Network, Video/Audio, Event Server, Motion detect, Event Config, Tools, USB, and Information. 4.2 Using Smart Wizard The Marmitek IP camera’s Smart Wizard lets you configure your camera easily and quickly. The wizard will guide you through the necessary settings with detailed instructions on each step. To start the wizard, click Smart Wizard in the left menu bar. Step 1.
Enter the name for the camera and place. Enter the administrator password. Step 2. IP Settings Select the IP setting according to your network: DHCP, Static IP, or PPPoE.
Step 3. Email Settings Enter the required information to be able to send email with image. Step 4. Wireless Networking* Complete the required settings for wireless networking.
Step 5. Confirm Settings This step shows the configuration of your camera. When you confirm the settings, click Apply to finish the wizard and reboot the camera. Otherwise, click Prev to go back to the previous step(s) and change the settings; or click Cancel to end the wizard and discard the changes.
4.3 Basic Setup The Basic menu contains three sub-menus that provide the system settings for the camera, such as the Camera Name, Location, Date & Time, and User management. Basic >> System Basic - Camera Name: Enter a descriptive name for the camera. - Location: Enter a descriptive name for the location used by the camera.
This item allows you to set the LED illumination as desired. There are two options: Normal and OFF. Basic >> Date & Time - TimeZone: Select the proper time zone for the region from the pull-down menu. - Synchronize with PC: Select this option and the date & time settings of the camera will be synchronized with the connected computer. - Synchronize with NTP Server: Select this option and the time will be synchronized with the NTP Server.
Basic >> User Administrator To prevent unauthorized access to the camera’s Web Configuration, you are strongly recommend to change the default administrator password. Type the administrator password twice to set and confirm the password. General User - User Name: Enter the user’s name you want to add to use the camera. - Password: Enter the password for the new user.
to the camera. To modify the user’s information, select the one you want to modify from UserList and click Add/Modify. - UserList: Display the existing users of the camera. To delete a user, select the one you want to delete and click Delete. Guest - User Name: Enter the guest’s name you want to add to use the camera. - Password: Enter the password for the new guest. - UserList: Display the existing guests of the camera. To delete a user, select the one you want to delete and click Delete.
4.4 Network Settings The Network menu contains three sub-menus that provide the network settings for the camera, such as the IP Setting, DDNS Setting, IP Filter, and Wireless network**.
This item allows you to select the IP address mode and set up the related configuration. The default setting is DHCP mode enabled. - DHCP: Select this option when your network uses the DHCP server. When the camera starts up, it will be assigned an IP address from the DHCP server automatically. - Static IP: Select this option to assign the IP address for the camera directly. You can use IPFinder to obtain the related setting values. IP Enter the IP address of the camera. The default setting is 192.168.0.30.
With the Dynamic DNS feature, you can assign a fixed host and domain name to a dynamic Internet IP address. Select the Enable option to enable this feature. Then, select the Provider from the pull-down list and enter the required information in the Host Name, User Name, and Password boxes. Please note that you have to sign up for DDNS service with the service provider first.
Network >> IP Filter The IP Filter setting allows the administrator of the camera to limit the users within a certain range of IP addresses to access the camera. Start/End IP Address Assign a range of IP addresses that are not allowed to access the camera by entering the Start IP address and End IP address. When you are finished, click Add to save the range setting. You can repeat the action to assign multiple ranges for the camera. For example, when you enter 192.168.0.50 in Start IP Address and 192.
Deny IP List The list displays the range setting(s) of IP addresses that are not allowed to access the camera. To clear the setting, select a range of IP addresses from the list and click Delete.
Network >> Wireless Setting* The camera supports WLAN while you use the wireless network. Select the Enable option to enable this feature. - Network ID (SSID}: Keep the default setting of this option to connect the camera to any access point under the infrastructure network mode. To connect the camera to a specified access point, set a SSID for the camera to correspond with the access point’s ESS-ID.
Click Site Survey to display the available wireless networks, so that you can easily connect to one of the listed wireless networks. List of searching results - Wireless Mode: Select the type of wireless communication for the camera: Infrastructure or Ad-Hoc. - Channel: Select the appropriate channel from the list. - Authentication: Select the authentication method to secure the camera from being used by unauthorized user: Open, Shared-key, WPA-PSK, and WPA2-PSK.
Encryption: Select the WEP option to enable the data encryption feature to secure the camera within the wireless network. Format: Once you enable the Encryption feature, you need to determine the encryption format by selecting ASCII or HEX. ASCII format causes each character you type to be interpreted as an eight-bit value. Hex format causes each pair of characters you type to be interpreted as an eight-bit value in hexadecimal (base 16) notation.
4.5 Pan/Tilt Settings** The Pan/Tilt menu allows you to configure the pan/tilt functions of the camera. Pan & Tilt >> Pan & Tilt Settings - Pan/Tilt Calibration: Click Calibration to calibrate the position of the camera lens. - Pan Steps: Set the changing range (1~20 degrees) when you click the Left/Right button. - Tilt Steps: Set the changing range (1~20 degrees) when you click the Up/Down button.
4.6 Setting up Video & Audio The Video & Audio menu contains three sub-menus that provide the video and audio settings for the camera. Video & Audio >> Camera Image Setting - Brightness: Adjust the brightness level from 0 ~ 100.
- Contrast: Adjust the contrast level from 0 ~ 100. - Saturation: Adjust the colors level from 0 ~ 100. Click Default to restore the default settings of the three options above. - Mirror: Select the Horizontal option to mirror the image horizontally. Select the Vertical option to mirror the image vertically. - Light Frequency: Select the proper frequency according to the camera’s location: 50Hz, 60Hz, or Outdoor.
Video & Audio >> Video MPEG4*** - Video Resolution: Select the desired video resolution from the three formats: VGA, QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses more resource within your network. - Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium, High, and Highest. - Frame Rate: Select Auto or a proper setting depending on your network status.
MJPEG - Video Resolution: Select the desired video resolution from the three formats: VGA, QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses more resource within your network. - Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium, High, and Highest. - Frame Rate: Select Auto or a proper setting depending on your network status. NOTE The camera supports both MPEG4 and MJPEG compression.
Video & Audio >> Audio**** ***** Camera Microphone In**** ***** Select the Enable option to enable the camera’s audio function, so that you can receive the on-site sound and voice from the camera. Camera Speaker Out***** Select the Enable option to enable the IP RoboCam 21 camera’s external speaker function, so that the connected speaker can play the sound and voice through the camera. - Volume: Set the speaker’s volume.
4.7 Event Server Configuration The Event Server menu contains three sub-menus that allow you to upload images to FTP, send emails that include still images, and store the images to a NAS system. When you complete the required settings for FTP, Email, or Network Storage, click Test to test the related configuration is correct or not. Once the camera connects to the server successfully, click Apply. Event Server Setting>> FTP - Host Address: Enter the IP address of the target FTP server.
- Password: Enter the password to login into the FTP server. - Directory Path: Enter the destination folder for uploading the images. For example, /Test/. - Passive Mode: Select the Enable option to enable passive mode. NOTE Due to the network environment, the camera may not upload the number of images that you set.
Event Server Setting >> Email - SMTP Server Address: Enter the mail server address. For example, smtp.com. - Sender Email Address: Enter the email address of the user who will send the email. For example, mymail@mail.com. - Sender User Name: Enter the user name to login the mail server. - Sender Password: Enter the password to login the mail server. - Receiver #1 Email Address: Enter the first email address of the user who will receive the email.
- Receiver #2 Email Address: Enter the second email address of the user who will receive the email. NOTE***** Due to the network environment, the camera may not send the number of images that you set. Event Server Setting >> Network Storage*** - Samba Server Address: Enter the IP address of the Network Storage server. - Share: Assign the folder on the Network Storage server to share the files to users. - Path: Assign the path for uploading the files on the Network Storage server. For example, /Test/.
- User Name: Enter the user name to login into the Network Storage server. - Password: Enter the password to login into the Network Storage server. - Split By: When the file is too large to upload smoothly, use this option to split it by selecting File Size or Recording Time. - When Disk Full: Select Stop Recording or Recycle – Delete Oldest Folder of File when the storage space on the Network Storage server is full. NOTE The video recorded files in Network Storage are enclosed by AVI format without Audio.
4.8 Motion Detect The Motion Detect menu contains the command and option that allow you to enable and set up the motion detection feature of the camera. The camera provides two detecting areas. To enable the detecting area, select Window 1 or 2 from the pulldown list, and then select Enable. When the detecting area is enabled, you can use the mouse to move the detecting area and change the area coverage. - Name: Assign a name to the detecting area.
NOTE Sliding the Threshold bar to the right will decrease the sensitivity of motion detection; sliding the Threshold bar to the left will increase the sensitivity of motion detection NOTE keep the two motion detection areas to a minimum size because this gives much bigger detection spikes, and the threshold can therefore be set higher, and so reduce false alerts due to sunlight changes. 4.9 Event Config The Event Config menu contains sub-menus that provide the commands to configure event profiles.
- Snapshot/Recording Subfolder: You can assign a descriptive name for the subfolder to save the captured image/video files. Otherwise, leave this option blank to use the default setting. - Network Storage Recording Time Per Event***: Limit the recording time while you are using the Network Storage solution. - GPIO Trigger Out Retention Time Per Event**: Limit the retention time of the GPIO Trigger Out function. Event Configuration >> Arrange Schedule Profile This sub-menu displays the scheduled profile(s).
- Profile Name: Display the profile name that you select in the Schedule Profiles list. - Weekdays: Select the weekday(s) that you want to separately assign in the schedule profile. The weekday that has been assigned will be displayed with green color. - Time List: Display the time period that you have assigned within the selected weekday.
- Schedule Profile: Select a schedule profile from the pulldown list. - Action: Set the Trigger Out** function or select the destination of the captured images: Save Image to USB***, Record to Network Storage***, Send Email, or FTP Upload. Event Configuration >> Schedule Trigger You can separately configure the schedule for trigger function of the Marmitek IP camera by Email, FTP, or Network Storage***.
Select the Enable option on each item, and then select a Schedule Profile from the pull-down list and set the Interval time. NOTE If the setting value of the Network Storage Recording Time Per Event option in General Setting is longer than the Interval time in Network Storage Schedule, the recorded file will be a continuous video clip.
Event Configuration >> GPIO Trigger** Select the Enable option to enable the GPIO trigger function of the camera, so that you can set Trigger Out function or send captured images within the detecting area to the FTP server, email receiver, Network Storage server***, or the connected USB*** device. You have to configure corresponding settings, such as FTP server and email server, to enable this feature. - Schedule Profile: Select a schedule profile from the pulldown list.
Record to Network Storage***, Send Email, or FTP Upload. 4.10 Tools The Tools menu provides the commands that allow you to restart or reset the Marmitek IP camera. You can also backup and restore your configuration, and upgrade the firmware for the camera.
Factory Reset Click Reset to restore all factory default settings for the camera. System Reboot Click Reboot to restart the camera just like turning the device off and on. The camera configuration will be retained after rebooting. Configuration You can save your camera configuration as a backup file on your computer. Whenever you want to resume the original settings, you can restore them by retrieving the backup file.
4.11 USB*** The USB menu provides the information and controls of the connected USB device. USB Dismount To safely remove the connected USB device, you can press the Unmount button for four seconds on the camera or click Dismount from this item. USB Information 60 Display the Total space and Free space of the USB device.
- When Disk Full: Select Stop Recording or Recycle – Delete Oldest Folder of File when the storage space on the USB device is full. NOTE The connected USB storage device can be used to store still images only and as your host system backup. It is not recommended to use the USB device as your major storage device.
4.12 Information The Information menu displays the current configuration and events log of the camera. Device Info Display the Basic, Video & Audio, Network, and Wireless settings of the camera. System Log The Logs table displays the events log recorded by the system.
A PPENDIX A.1 Specification Image Sensor Sensor Resolution 1/4” color CMOS 640x480 Video Compression MJPEG****** MPEG4/MJPEG*** Video resolution VGA/QVGA/QQVGA; 30fps max. Audio Input**** ***** Output***** Codec Built-in MIC Mono 3.5 mm mini jack plug PCM/AMR (AMR is for 3GPP only) User Interface One RJ-45 port Antenna* One external antenna Reset One Reset button USB*** USB 1.1 port, with one unmount button; Power distribution: 500mA Max.
System Hardware Processor RAM ROM ARM9 base 32MB SDRAM 4MB NOR Flash****** 8MB NOR Flash*** DC 12V(IP Robocam) Power DC 5V (IP Eye AnyWhere) Communication LAN WLAN* 10/100Mbps Fast Ethernet, auto-sensed, Auto-MDIX IEEE 802.11b/g Protocol support****** TCP/IP, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, FTP, HTTP, PPPoE, UPnP.
Temperature - Operation: 0qC ~ 45qC - Storage: -15qC ~ 60qC Humidity - Operation: 20% ~ 85% non-condensing - Storage: 0% ~ 90% non-condensing EMI FCC Class B, CE Class B A.2 GPIO Terminal Application** Typically used in association with programming scripts for developing applications for motion detection, event triggering, alarm notification via e-mail, and a variety of external control functions.
Interface Schematic NOTE:You can use a Marmitek SM10 Universal X-10 sender to transform the output into an X-10 signal for controlling appliances and lights , that are plugged into the Marmitek X-10 modules, through the existing house wiring. Automatically switches all lights (on or flashing) in case of alarm, without running any extra wires. Switch appliances and lights in your home without extra cables.
A.3 Glossary of Terms NUMBERS 10BASE-T 100BASE-TX 10BASE-T is Ethernet over UTP Category III, IV, or V unshielded twisted-pair media. The two-pair twisted-media implementation of 100BASET is called 100BASE-TX. A ADPCM AMR Applet ASCII ARP AVI Adaptive Differential Pulse Code Modulation, a new technology improved from PCM, which encodes analog sounds to digital form.
C Communication Connection Communication has four components: sender, receiver, message, and medium. In networks, devices and application tasks and processes communicate messages to each other over media. They represent the sender and receivers. The data they send is the message. The cabling or transmission method they use is the medium. In networking, two devices establish a connection to communicate with each other.
Enterprise network Ethernet An enterprise network consists of collections of networks connected to each other over a geographically dispersed area. The enterprise network serves the needs of a widely distributed company and operates the company’s mission-critical applications. The most popular LAN communication technology. There are a variety of types of Ethernet, including 10Mbps (traditional Ethernet), 100Mbps (Fast Ethernet), and 1,000Mbps (Gigabit Ethernet).
H HEX Short for hexadecimal refers to the base-16 number system, which consists of 16 unique symbols: the numbers 0 to 9 and the letters A to F. For example, the decimal number 15 is represented as F in the hexadecimal numbering system. The hexadecimal system is useful because it can represent every byte (8 bits) as two consecutive hexadecimal digits. It is easier for humans to read hexadecimal numbers than binary numbers.
ISP ISP (Internet Service Provider) is a company that maintains a network that is linked to the Internet by way of a dedicated communication line. An ISP offers the use of its dedicated communication lines to companies or individuals who can’t afford the high monthly cost for a direct connection. J JAVA Java is a programming language that is specially designed for writing programs that can be safely downloaded to your computer through the Internet without the fear of viruses.
Network NWay Protocol may not be valid outside your network. NAT solves the problem. When devices within your network request information from the Internet, the requests are forwarded to the Internet under the router's IP address. NAT distributes the responses to the proper IP addresses within your network. A network consists of a collection of two or more devices, people, or components that communicate with each other over physical or virtual media.
Protocol Communication on the network is governed by sets of rules called protocols. Protocols provide the guidelines devices use to communicate with each other, and thus they have different functions. Some protocols are responsible for formatting and presenting and presenting data that will be transferred from file server memory to the file server’s net work adapter Others are responsible for filtering information between networks and forwarding data to its destination.
Server SIP SMTP SNMP Station Subnet mask It is a simple computer that provides resources, such as files or other information. SIP (Session Initiated Protocol) is a standard protocol that delivers the real-time communication for Voice over IP (VoIP), which establishes sessions for features such as audio and video conferencing. The Simple Mail Transfer Protocol is used for Internet mail. Simple Network Management Protocol. SNMP was designed to provide a common foundation for managing network devices.
User Name Utility UTP The USERNAME is the unique name assigned to each person who has access to the LAN. It is a program that performs a specific task. Unshielded twisted-pair. UTP is a form of cable used by all access methods. It consists of several pairs of wires enclosed in an unshielded sheath. W WAN WEP Windows WPA WPA2 Wide-Area Network.
Marmitek is a trademark of Marmidenko B.V. IP EYE ANYWHERE + IP ROBOCAM is a trademark of Marmitek B.V. All rights reserved. Copyright and all other proprietary rights in the content (including but not limited to model numbers, software, audio, video, text and photographs) rests with Marmitek B.V. Any use of the Content, but without limitation, distribution, reproduction, modification, display or transmission without the prior written consent of Marmitek is strictly prohibited.
IP Eye Anywhere ™ IP RoboCam ™ 77
