Built-in Duplex Multiplexer & Pan/Tilt Control 14” COLOR OBSERVATION SYSTEM Built-in Duplex Multiplexer Built-in Pan/Tilt Control Real-Time Display LIVE/PB Digital Zoom Owner’s Manual
SAFETY INFORMATIONS These symbols with supplemental markings are at the rear of the monitor CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER, NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SAFETY INSTRUCTIONS Warning! Important Safety Instructions 1) Read Instructions All the safety and operating instructions should be read before the appliance is operated. 2) Retain Instructions The safety and operating instructions should be retained for future reference. 3) Heed Warnings All warnings on the product and in the operating instructions should be adhered to. mounting accessory recommended by the manufacturer. 9) An product and cart combination should be moved with care.
SAFETY INSTRUCTIONS Alternate Warnings This product is equipped with a three-wire grounding-type plug a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
SAFETY INSTRUCTIONS 22) Replacement Parts When replacements parts are required, be sure the service technician has used replacements parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may results in fire, electric shock or other hazards. 23) Safety Check Upon completion of any service or repairs to this receiver, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
CONTENTS INTRODUCTION ................................................................................................................................... 1 MONITOR SYSTEM PART NAME FRONT PANEL ............................................................................................................................... 2 BACK PANEL ..................................................................................................................................
PRIOR TO USE PRIOR TO USE This is the basic manual for Built-in Mux Control 14” Color Observation System user. The content of this manual is focused on product introduction, installing method, connecting method with other devices, using method of various functional buttons, and system setting method with the setup menu.
INTRODUCTION This equipment will give you added security and comfort for many years. It is easy to install in almost anywhere you need audio/video surveillance. To safely use all the high technical functions of the unit, please read the installation and operating instruction in manual, and keep it for the future reference. Also, it can directly control Pan/Tilt Dome Camera without any extra controller.
MONITOR SYSTEM PART NAME Front Panel 15 1 2 4 6 8 3 5 7 9 10 1 CHANNEL SELECT BUTTONS - In Live / PB mode : When desired channel button is pressed, a full screen of the channel is displayed. - Menu(S.MENU) mode Button : To move throughout each item of the Main Menu or that of the sub menu to set it up. Button : To increase or decrease the value of each item. - Pan/Tilt Dome Camera Control 2 QUAD Quad Screen display in LIVE or PB.
MONITOR SYSTEM PART NAME Back Panel 1 AC INPUT This is an input terminal that connects to AC 100~240V power. 2 VIDEO INPUT/OUTPUT CONNECTORS • BNC camera inputs 1~4 : These inputs are used for standard cameras with BNC type connectors. • Looping outputs 1~4 : These are looping outputs for cameras on through. It can be used to display or record the pictures on a separate monitor or recorder.
MULTIPLEXER SYSTEM OPERATION This chapter shows you how to execute various modes using the system setup menu. STARTING THE SETUP MODE 1. Check the power cables of the equipment connected to Monitor and turn the power switch. 2. Press the S. Menu button on the front panel. Note Only while in Live Mode, you can enter the setup mode. MAIN MENU Press the “S. MENU” button on the front of the system, the main menu of the system setup appears as follows.
MULTIPLEXER SYSTEM OPERATION SUB MENU SETTING 1. CAMERA INPUT SET - Set channel [ON], if camera is connected to the channel, and set channel [OFF] if camera is not connected to the channel. - If the channel is set to [OFF], missing video input signals are not treated as LOSS. • From the
MULTIPLEXER SYSTEM OPERATION 3. DATE/TIME SET - Setting up date and time - 1. DATE FORM: (1) : Select one of the following appropriate date forms to display date. <1>DD/MM/YYYY : Day / Month / Year <2>MM/DD/YYYY : Month / Day / Year <3>YYYY/MM/DD : Year / Month / Day • Set the cursor on the 3.DATE/TIME SET using , and keys from the , and then press ENTER key. [DATE/TIME SET] screen appears. • Press or key to move the cursor up and down.
MULTIPLEXER SYSTEM OPERATION 5. REC TYPE SET - Allows setting of the recording mode of TIME LAPSE VCR to be connected with MULTIPLEXER. • Set the cursor on the 5.REC TYPE SET using and keys, and press ENTER key to enter the SUB MENU on the right. • To record intermittently, locate the cursor on the 1. TIMELAPSE using and keys, and press ENTER key. To record in 60 fields/sec (NTSC standard) or 50 fields/sec (PAL standard), select 2. REAL TIME and press ENTER key.
MULTIPLEXER SYSTEM OPERATION 7. ALARM / LOSS LIST • To view up to 10ALARM/LOSS history records, From the
OBSERVATION CAMERA OPERATION CAMERA PART RJ TYPE DIN TYPE IRIS 4 INTERPHONE 5 3 2 8 6 TERMINAL 7 TO MONITOR LEVEL 9 MONITOR 1 10 1. CCD CAMERA LENS Deliver sharp image to the CCD sensor. 5. MONITOR INPUT JACK Din connect the cable with the monitor. 2. MICROPHONE Pick up sound around the camera. 6. INTERPHONE 3. SPEAKER Delivers the sound from the monitor 4. ALARM TERMINAL Connect an optional alarm device to this terminal.
PAN/TILT DOME CAMERA OPERATION CAMERA PART Electrical power is not connected to the dome and observation / quad monitor during installation. A 105 TOP VIEW 107 FRONT VIEW 105 or CAMERA IN STALLATION Adaptor plate Ø3 x 20 screw Hook Base (hold base when you twist to attach the dome to adaptor plate) Swivel Bubble Be sure that no power is connected to dome camera and observation / quad monitor during installation. 1. Twist open the clear dome cover to CCW to reach inside the dome camera. 2.
REMOTE CONTROL UNIT POWER ID NO 0 1 2 3 4 5 6 7 8 9 1 CH1 2 CH3 3 CH2 4 VCR RECORD LIVE/PB PLAY RB THRU FREEZE QUAD/MULTI 6 CH1 CH3 MENU CH4 ENTER/P.T VOL RECORD LIVE/PB P.MENU PLAY PB THRU VOL 10 FREEZE ZOOM 11 QUAD/MULTI 8 5 CH4 14 VOLUME UP ENTER/P.T P.MENU 15 16 17 9 12 MENU (SYSTEM) CH2 VCR 7 13 ACTION AUTO MULTIPLEXER CNTROL 18 19 20 VOLUME DOWN ACTION ZOOM AUTO This remote control unit is commonly used in various model.
REMOTE CONTROL UNIT 1 POWER Press to turn the MONITOR on and off. 12 QUAD/MULTI Used in the quad display monitor only 2 CH1 ( ) CH1 button enables the camera 1 to be displayed in a single mode. 13 MENU(SYSTEM) Display the system main menu on the screen. You can set up CAM INPUT SET, CH_TITLE SET, DATE/TIME SET, AUTO SWITCH SET, REC TYPE SET ALARM/LOSS SET and ALARM/LOSS LIST. 3 CH2 ( ) CH2 button enables the camera 2 to be displayed in a single mode.
SYSTEM OPERATION STANDARD CAMERA OPERATION MONITOR REAR VIEW STANDARD CAMERA CH1 CH2 CH3 or CH4 CH1 CH2 CH3 CH4 VIDEO AUDIO MONITOR OUT Some models has the RJ IN. (Optionable) STANDARD CAMERA INSTALLATION MULTIPLE CAMERA OPERATION MONITOR REAR VIEW CAMERA REAR VIEW TERMINAL DIN TO MONITOR CH1 CH2 CH3 CH4 or ACTION IRIS CH1 INTERPHONE H3 CH4 VIDEO AUDIO VCR VIDEO CH2 AUDIO CH3 MONITOR OUT LEVEL MONITOR CH4 Some models has the RJ IN.
SYSTEM OPERATION OBSERVATION CAMERA TWO WAY INTERCOM INSTALLATION Camera with intercom installation (RJ TYPE) (DIN TYPE) CAMERA (REAR VIEW) CAMERA (REAR VIEW) IRIS TERMINAL INTERPHONE TO MONITOR LEVEL 2m RJ Cable (Supplied) MONITOR (REAR VIEW) 2m DIN Cable (Supplied) MONITOR MONITOR (REAR VIEW) INTERCOM BOX CH1 CALL INTERCOM BOX 1 CH2 CH1 CH3 CALL CH2 CH4 CH3 CH4 ACTION IN VIDEO POWER AUDIO OUT AC IN CH1 CH2 CH3 CH4 VIDEO VIDEO MONITOR OUT AUDIO VCR Normal Standard DIN Cab
SYSTEM OPERATION PAN/TILT DOME CAMERA OPERATION MONITOR REAR VIEW CH1 STANDARD DOME CAMERA CH2 CH3 CH1 or CH4 CH2 CH3 CH4 VIDEO AUDIO EO MONITOR OUT AUDIO VCR PAN/TILT DOME CAMERA INSTALLATION MULTIPLE PAN/TILT DOME CAMERA OPERATION MONITOR REAR VIEW CH1 CH2 CH3 CH4 or ACTION CH1 H2 CH3 VIDEO CH4 VIDEO AUDIO VCR VIDEO CH2 AUDIO CH3 MONITOR OUT CH4 MULTIPLE PAN/TILT CAMERA INSTALLATION 1. Connect all camera cables and verify operation, as shown above.
SYSTEM OPERATION MULTIPLE SYSTEM OPERATION ID NO 0 1 2 3 4 5 6 7 8 9 Built-in Mux Monitor CH1 CH3 MENU VCR ENTER/P.T CH4 Slave monitor CH2 RECORD LIVE/PB PLAY PB THRU FREEZE ZOOM QUAD/MULTI VOL P.MENU VOL ACTION AUTO MULTIPLEXER CNTROL CH1 CH2 VCR RECORD PLAY CH3 CH4 AUTO S.MENU ENTER TALK ACTION P.
AUXILIARY OPERATION INSTALLATION MONITOR REAR VIEW CH1 CH2 EXTRA MONITOR CH3 CH4 ACTION VIDEO AUDIO CH1 CH2 CH3 VIDEO CH4 VIDEO AUDIO VCR MONITOR OUT EXTRA MONITOR INSTALLATION VCR OPERATION CH1 CH2 CH3 CH4 ACTION IN VIDEO OUT AUDIO POWER AC IN CH1 CH2 CH3 VIDEO CH4 VIDEO MONITOR OUT AUDIO VCR IN COM OUT S/W OUT TYPICAL TIME LAPSE RECORDER REAR VIEW OBSERVATION MONITOR WITH A RECORDER 1.
AUXILIARY OPERATION 2. In case of REAL TIME record mode, camera signal output is automatically switched by fields regardless of the SW TRIGGER signal from the VCR. In case of TIME LAPSE record mode, camera signal output is automatially switched by field or frame of the SW TRIGGER signal from the TIME LAPSE VCR. Switch out timing of TIME LAPSE VCR must be selected frame. If switch out timing of TIME LAPSE VCR is selected field, the recording image missed some fields. 3.
AUXILIARY OPERATION ALARM OPERATION A. Monitor Alarm Circuit MONITOR ALARM CIRCUIT B. Alarm Connection There are two ways to connect with alarm. One is to connect with terminal Block on the back panel of monitor and the other is with AUX port on rear panel of camera. B-a. Terminal Block Connection or ALARM SYSTEM SENSOR 1 SENSOR 2 SENSOR 3 SENSOR 4 ALARM DEVICE INSTALLATION (In case of using TIME LAPSE VCR) 1. SW IN -GND : This is the COMMON Ground for ALARM OUT & IN.
AUXILIARY OPERATION C. ALARM OPERATION When an alarm is activated, the associated camera video displays full screen, the word ALARM displays on screen, a buzzer, if programmed "30 SEC", generates a continuous audible alarm for 30 seconds and the alarm output relay activates. If the second or third sensor is activated while the first alarm is operating, the screen will switch to the second or third sensing camera. Pressing the VCR KEY resets the alarm condition.
AUXILIARY OPERATION (near real-time recording). e.g., If ALARM occurred in ALARM SENSOR 1 interoperating with camera 1, the order of record out would be : 1 - 2 - 1 - 3 - 1 - 4 - 1 - 1 - 2 - 1 - 3 - 1 - 4 - 1 - 1 - 2...... When ALARM is cancelled by pressing key or the expiration of HOLD TIME, the frequency of channel recording is returned to the original status. If ALARM occurs during PB, screen is turned to QUAD screen automatically.
SPECIFICATIONS 14” BUILT-IN MUX COLOR MONITOR System Picture Tube NTSC PAL 14Inch CRT, 0.66mm stripe pitch, 90º deflection Visible picture size 33.
SPECIFICATIONS MULTIPLEXER System PIXCEL RESOLUTION 23 NTSC FULL : 720(H) QUAD : 360(H) PAL 480(V) 240(V) FULL : 720(H) QUAD : 360(H) VCR TRIGER IN TTL Negative Pulse ALARM IN TTL Negative Pulse Make Contact (4EA) ALARM OUT Contact RELAY (Normal OPEN) ALARM HOLD TIME 1~30MIN (1MIN/PER) 1~60SEC (5SEC/PER) CHANNEL TITLE EACH CHANNEL 8 CHARACTERS DATE/TIME YYYY/MM/DD, MMDD/YYYY, DD/MM/YYYY HH/MM/SS ALARM INDICATION "A" FREEZE INDICATION "F" CHANNEL LOSS BLUE BACK SCREEN or "L" DISPLAY Q
SPECIFICATIONS CAMERA (PAN/TILT DOME COLOR CAMERA) System NTSC PAL DIN : DC12V (From Monitor) Power source RJ : DC15V (From Monitor) Image sensor Active pixels 1/3” Interline transfer CCD 512(H) x 492(V) 512(H) x 582(V) Image sensor area 4.8(H) x 3.7(V)mm Signal to noise 46dB Electronic IRIS 1/100,000 sec Synchronization External Signal format 525 lines, 2:1 interface 625 lines, 2:1 interface Video output 1.
SPECIFICATIONS CAMERA (OBSERVATION COLOR CAMERA) System NTSC PAL Pick-up device No. of picture elements 1/3” or 1/4” color CCD 512(H) x 492(V) 512(H) x 582(V) Horizontal resolution > 330 TVL Light sensitivity 3.5 ~ 30,000 Lux Spectral sensitivity range 400 ~ 1,000 nm Signal to noise ratio > 48dB White balance Auto TTL, 2,500 ~ 6,500°K Built-in microphone Electric Speaker 0.3W Lens type C/CS mount Lens viewing angle 59°H ~ 46°V Lens focal length F1.2 Lens min.
ACCESSORIES Additional camera available Optional camera Optional Pan/Tilt Dome camera Day-night camera Slave Monitor VCR STOP/EJECT REC POWER VIDEO A SHARP BRIGHT TINT COLOR CONTRAST VOLUME POWER B ADJUST Intercom Box Weather proof housing Extension connector jack CALL 12mm 1.5 0.5 Wide angle lens (8mm / 12mm) 1 0.
USER’S GUIDE 1. RECORDING TO VCR 1) TIMELAPSE MODE - Channel to be recorded is switched, whenever NEGATIVE SWITCHING PULSE through SW OUT port of TERMINAL arrives from TIME LAPSE VCR. Therefore, the interval of channel switching is determined by recording time of TIME LAPSE VCR. Since as the recording time increases, the time interval between channels to be recorded becomes longer so that the probability of missing important scene grows.
USER’S GUIDE 3. VIEWING FULL SCREEN When the desired channel among the 4buttons of “CH1, CH2, CH3, CH4” on the front side of Monitor is pressed, the selected channel appears in Full screen. 4. VIEWING QUAD SCREEN If user presses the “Quad” button on the front side of Monitor, the Quad image appears. 5. VIEWING AUTO SEQUENCE TRANSITION SCREEN The Auto Sequence Transition Screen mode enables user to switch between channels on one, quad, multi screen.
TROUBLE SHOOTING GUIDE While using the system, certain unexpected situations may cause problem with the system. In many cases, system trouble can be solved through a simple trouble shooting check. If you encounter any problems using this system, please check the following points. 1. When the Power will not turn on Check whether the power cord is properly plugged in. 2. When the Power is on but the screen does not appear. Check whether the camera, monitor and output terminals are properly connected. 3.
MEMO 30
MEMO 31
MEMO 32
