User Manual
04
FRONT PANEL
1) INPUT 1 Connect your bass to this input using a standard ¼” shielded instrument cable.
2) CH1/CH2/MIX This channel selector switches between the Channel 1 and Channel 2 or mix
the two channels. Channel-switching/mix can also be controlled by a EVO
pedal that can be plugged into the MIDI IN on the rear panel (30).
3) AMP 1 Select between six AMPS tone choices available at channel 1.
FACTORY SETTING CH1
• Little Mark III (Markbass Little Mark III)
agship Markbass amplier, solid-state preamp with warm and natural sound,
faithfully reproduces the true tone of your instrument
• T-Green90 (TRACE ELLIOT ® GP12)
solid state, Nineteen tone, scooped but “solid” sound
• RB7Hundred (G&K ® RB 700 ®)
solid state, quite modern sound, “GK growl” tone
• Blue ‘70 (Ampeg ® SVT-VR ® Blue Line)
tube, classic big tone, iconic rock sound
• TTE500 (Markbass TTE 500)
tube, “Modern Vintage”, thunderous all-valve tone (Tube Technology
Emulator)
• Sunny US (SUNN ® T)
vintage, true classic rock tone
note: You can update AMPs choices for each channel as for your preference thanks to
the MARKBASS EVO SOFTWARE)
CH1
CH2
INPUT 2
INPUT 1
MIX
AUX
CH2
AMP 2 GAIN LOW MID HIGH LEVEL FX 2 LEVEL MIX
Min
Max
CH1
CH2
1
2
3
4
5
6
0
Max
0
Max
FX 2 MIX
MARKBASSMARKBASSMARKBASS
B E A D G C
MUTE
-
TUNER
AMP 1 GAIN LOW MID HIGH LEVEL FX 1 LEVEL MASTER PHONES LEVEL
CH1
1
2
3
4
5
6
Min
Max
0
Max
0
Max
0 Max
0
Max
FX 1 BOOST
i
PHONES
CLASS 2 WIRING
1 + = SIGNAL
1 - = GND
MIDI IN USB
SEND 1 SEND 2 RETURN 1 RETURN 2 LINE OUT
1
POST MIX
LINE OUT
2
GND LIFT
SPEAKER OUT
LOOP
PRE MIX
MINIMUM
LOAD
4 OHM
CAUTION:
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE
REPLACE ONLY WITH SAME
TYPE AND RATING FUSE.
ATTENTION:
REMPLACER UNIQUEMENT PAR
UN FUSIBLE DE MEME TYPE.
27
28
29
30
31
32
33
34
35
3637
38
39
1
2
3
4
5
6
10
11
12 13
14 15
16
17
18
19
20
21
22
23
8
9
24
25
26
7
4) GAIN This knob sets the gain level of the channel 1.
5) LOW This knob controls the amount of low frequencies of the selected AMP / CH1.
6) MID The Mid control regulates the midrange frequencies of the selected AMP /
CH1.
7) HIGH The High knob controls the amount of high frequencies of the selected AMP /
CH1.
8) LEVEL Controls the level of the selected AMP model on CH1.
9) FX 1 LEVEL Controls the level of the eect of channel 1.
FX FACTORY SETTING CH1: COMPRESSORE
note: - You can update FX choices for each channel and customize their parameters as
for your preference thanks to the MARKBASS EVO SOFTWARE.
- FX ON/OFF switching can be controlled by the EVO pedal.
- In MIX mode the eects don’t work simultaneously.
10) INPUT 2 Connect your bass to this input using a standard ¼” shielded instrument cable.
note: You can use simultaneously the two inputs connecting two instruments and use
the Markbass EVO 1 as two channels amp.
11) AUX Use this input to plug in an iPod, CD or MP3 player using a stereo mini plug
1/8”. This signal mixes in evenly with the instrument/s connected to the
input/s.