N 585 0 N 585.
TABLE OF CONTENTS / ABOUT THIS DOCUMENT TABLE OF CONTENTS About This Document 1 Installation Considerations Unpacking, Placement and Ventilation, Power Requirements, Operating States 2 Getting Started Front-Panel Overview, Rear-Panel Overview, Remote Control Overview 4 Quick Setup and Listen Remote Control, Initial Connections 11 Troubleshooting 14 Specifications 15 ABOUT THIS DOCUMENT For the purposes of this guide , we will refer both the N0585.
INSTALLATION CONSIDERATIONS INSTALLATION CONSIDERATIONS UNPACKING PLACEMENT AND VENTILATION When unpacking your N0585: • Install the integrated amplifier on a shelf with nothing above it, such as the top shelf in an open rack, to ensure proper ventilation. Do NOT install the integrated amplifier inside of an enclosed cabinet or rack. • Save all packing materials in case you need to ship your N0585 in the future. • Inspect your N0585 for signs of damage during shipment.
INSTALLATION CONSIDERATIONS POWER REQUIREMENTS OPERATING STATES The Nº585 is configured at the factory for 100, 115, or 230 VAC power operation at 50Hz or 60Hz. Before operating the amplifier, ensure that the power label on the rear panel near the AC input connector indicates the correct operating voltage. A detachable IEC power cable intended for use in the region where the N0585 is sold is included.
GETTING STARTED GETTING STARTED FRONT-PANEL OVERVIEW Select Knob Front-Panel Display IR Receiver Standby Button and LED Setup Button and LED Polarity Button and LED Enter Button Front-panel controls/indicators NOTE: For complete information about the functions of the front-panel controls and their settings parameters, see the N0585 User Guide. at www.marklevinson.com. Select knob: Rotate this knob to select the desired input to send to the Speaker outputs and Line outputs.
GETTING STARTED Display Intensity button: Press this button to change the intensity of the N0585’s front-panel Display characters and its front-panel LEDs. Multiple presses of the Display Intensity button cycle through the available brightness levels: High, Medium, Low, and Off. Standby button and LED: Press this button to put the N0585 into and out of the Standby mode. The LED illuminates when the N0585 is On. When the N0585 is in either the Green, Normal or Power Save Standby mode it flashes slowly.
GETTING STARTED REAR-PANEL OVERVIEW Right Channel Balanced Analog Input Connector Left Channel Balanced Analog Input Connector Phono Inputs And Ground Terminal (N0585.
GETTING STARTED NOTE: For complete information about the rearpanel connections, see the N0585 User Guide. at www. marklevinson.com. Left and right channel loudspeaker binding posts: The Nº585 utilizes custom-made, gold-plated, high-current loudspeaker binding posts. The positive binding posts, labeled + (positive), are red; the negative binding posts are black and are labeled – (negative). The binding posts can accommodate speaker cables terminated in untinned bare wire, spade lugs and banana plugs.
GETTING STARTED Ethernet port: This port supports connection to a home network. For information on how to configure and use the Ethernet port, see the N0585 User Guide. IR input connector: This connector accepts IR (infrared) control signals from other equipment. RS-232 port: This RJ-11 connector provides serial control through a standard RS-232 connection. Trigger output connector: This 3.
GETTING STARTED REMOTE CONTROL OVERVIEW NOTE: For complete information about the remote control functions, see the N0585 User Guide. at www. marklevinson.com. Standby Button Standby button: Press this button to put the N0585 into and out of the Standby mode. Select Buttons Volume Buttons Setup Button Mute Button Enter Button Balance Button Clari-Fi Button Polarity Button Display Button USB Control Buttons Select buttons: Press these buttons to select the desired input.
GETTING STARTED Polarity button: Pressing this button inverts the absolute polarity of the signal at the Speaker outputs and the Line outputs. The Polarity LED on the front panel illuminates when the signal's polarity is inverted. Display button: Press this button to change the intensity of the N0585’s front-panel display characters and its frontpanel LEDs. Multiple presses of the Display button cycle through the available brightness levels: High, Medium, Low, and Off.
QUICK SETUP AND LISTEN QUICK SETUP AND LISTEN REMOTE CONTROL Battery Installation Your N0585 remote control comes with two AAA alkaline batteries. To install the batteries, remove the remote control’s battery cover, insert the batteries and replace the battery cover. Be sure to observe proper battery polarity. Using the Remote Control When using the remote control, aim it toward the N0585's front panel IR receiver. Make sure that no objects, such as furniture, block the remote’s view of the receiver.
QUICK SETUP AND LISTEN INITIAL CONNECTIONS NOTE: For complete information about making connections, see the N0585 User Guide. at www. marklevinson.com. CAUTION: Before making connections, make sure the N0585 and all associated components are powered off and disconnected from electrical outlets. 1. Connect your speakers to the N0585's loudspeaker binding posts.
QUICK SETUP AND LISTEN Digital Source Component Computer To Digital Output To USB Port Single-Ended Analog Source Component Balanced Analog Source Component S/N Right Speaker Left Speaker N0585 / N0585.
TROUBLESHOOTING TROUBLESHOOTING If the N0585 experiences a potentially damaging condition, its built-in protection circuitry will shut off the amplifier and its Front-Panel Display will show one of the error messages listed below. Follow the instructions in the Solution column to correct the condition before attempting to use the N0585 again.
SPECIFICATIONS SPECIFICATIONS AMPLIFIER SECTION Output Power: 200W RMS per channel @ 8 Ω, 20Hz – 20kHz Damping Factor: >400 @ 20Hz, referred to 8 Ω Frequency Response: 20Hz – 20kHz, ±0.13dB; 2Hz – 250kHz, +0.2dB/–3dB Signal-to-Noise Ratio: >98dB (20Hz – 20kHz, unweighted); >103dB (20Hz – 20kHz, A-wtd), referred to full output – maximum volume setting Voltage Gain: 40.7dB (maximum volume setting) Total Harmonic Distortion: <0.01% @ 1kHz, 200W, 8 Ω; <0.
PHONO STAGE (N0585.5 ONLY) Riaa Frequency Response: 20Hz to 20kHz, ±0.3dB Infrasonic Filter: Defeatable, 15Hz, 2nd order (12dB/octave) Moving Magnet Mode: Input Resistance: 47kΩ Input Capacitance: Selectable; 50, 100, 150, 200, or 680pF Gain: 40dB @ 1kHz Total Harmonic Distortion Plus Noise: <0.
