NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction MARCY POWER STATION TC-3508 Parts List Warranty Ordering Parts Model TC-3508 Retain This Manual for Reference 140701 OWNER'S MANUAL IMPEX® INC. 2801 S. Towne Ave. Pomona, CA 91766 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com support@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 5 EXPLODED DIAGRAM……………………………………………………………… 9 PARTS LIST..........................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The warning label shown here has been placed on the Rear Base. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK 4
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Lower Vertical Frame (#2) to the Rear Base (#4). Secure it with two M10 x 3 ½” Carriage Bolts (#32), one U-shaped Bracket (#14), two Ø ¾” Washers (#35), and two M10 Aircraft Nuts (#33). B.) Attach the Right & Left Stabilizers (#5 & #6) to the Lower Vertical Frame.
STEP-2 (See Diagram 2) A.) Attach the Upper Vertical Frame (#1) onto the Lower Vertical Frame (#2). Secure it with two L-shaped Brackets (#9), two M10 x 3” Carriage Bolts (#31) from the front, two M10 x 3 5/8” Carriage Bolts (#30) from the side, four ∅ ¾” Washers (#35), and four M10 Aircraft Nuts (#33). B.) Attach the Chin-up Bar (#3) to the front of Upper Vertical Frame. Secure it with two M10 x 2” Allen Bolts (#25) and ∅ ¾” Washers (#35). Cover the Bolts with a 2” x 2 ¾” Plastic Cover (#16).
STEP 3 (See Diagram 3) A.) Attach the Left & Right Dip Supports (#7 & #8) to the Upper Vertical Frame (#1). Secure them to the Upper Vertical Frame with one M12 x 3 ¾” Allan Bolt (#26), two ∅ ¾” Washers (#37), and one M10 Aircraft Nut (#34). Do NOT over tighten the nut and bolt. Make sure the arms are able to move freely. B.) Secure the Left & Right Dip Supports together with one Four-hole Bracket (# 15) and four M8 x 3/8” Allen Bolts (#29). C.
STEP 4 (See Diagram 4) A.) Attach the Backrest Pad (#12) to the Upper Vertical Frame (#1). Secure it with two M8 x 2 ¾” Allen Bolts (#28) and ∅ 5/8” Washers (#36). B.) Attach the Arm Pads (#11) to the Left & Right Dip Supports (#7 & #8). Secure each Arm Pad with two M8 x 2 ¾” Allen Bolts (#28) and Ø 5/8” Curved Washers (#39). C.) Insert a Foam Tube (#10) halfway through the holes on the Lower Vertical Frame (#2). Push two Foam Rolls (#24) onto the Tube from both ends.
EXPLODED DIAGRAM 9
Parts list KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
