ST7001N DFU cover 05.7.
ST7001N DFU cover 05.7.21 5:22 PM ページ1 ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase.
ST7001N DFU cover 05.7.21 5:22 PM ページ2 CE MARKING English The ST7001 is in conformity with the EMC directive and low-voltage directive. Français Le ST7001 est conforme à la directive EMC et à la directive sur les basses tensions. Deutsch Das Modell ST7001 entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte. Nederlands De ST7001 voldoet aan de EMC eisen en de vereisten voor laag-voltage. Español El ST7001 está de acuerdo con las normas EMC y las relacionadas con baja tensión.
ST7001N DFU cover 05.7.21 5:22 PM ページ3 Español ADVERTENCIAS - No exponga el equipo a la lluvia ni a la humedad. - No extraiga la tapa del equipo. - No introduzca nada en el interior del equipo a través de los orificios de ventilación. - No maneje el cable de alimentación con las manos mojadas. - No cubra la ventilación con objetos como manteles, periódicos, cortinas, etc. - No deben colocarse sobre el equipo elementos con fuego, por ejemplo velas encendidas.
ST7001N 01 Eng 05.7.21 5:23 PM ページ1 ENGLISH CONTENTS FEATURES .............................................................................................................................................1 BEFORE USE .........................................................................................................................................2 PART NAMES AND FUNCTIONS ..........................................................................................................4 FRONT PANEL ..........
ST7001N 01 Eng 05.7.21 5:23 PM ページ2 ENGLISH BEFORE USE This section must be read before any connection is made to the mains supply. 7 EQUIPMENT MAINS WORKING SETTING • Noise or disturbance tends to occur particularly when using indoor antennas or 300 Ω/ohms feeder wires. We recommend using outdoor antennas and 75 Ω/ohms coaxial cables. Note For heat dispersal, do not install this equipment in a confined space such as a book case or similar unit.
ST7001N 01 Eng 05.7.21 5:23 PM ページ3 7 Loading batteries Before using the supplied remote control unit for the first time, load the batteries in the remote control unit. The batteries provided are used to verify the operations of the remote control unit only. 1. Take hold of the tab on the battery cover which is found on the back side of the remote control unit, and pull it up.
ST7001N 01 Eng 05.7.21 5:23 PM ページ4 ENGLISH PART NAMES AND FUNCTIONS FRONT PANEL For details on the functions of these parts, refer to the pages given in parenthesis. TUNING/PRESET DAB/FM/AM TUNER ST7001 STANDBY SECONDARY TUNED RDS STEREO POWER ON/STANDBY DIMMER DISPLAY MENU AUTO TUNE BAND SELECT PUSH ENTER e q w r t q Power ON/STANDBY switch This is used to turn the unit’s power ON and STANDBY.
ST7001N 01 Eng 05.7.21 5:23 PM ページ5 ENGLISH PART NAMES AND FUNCTIONS REAR PANEL ANTENNA REMOTE CONTROL MODEL NO. ST7001 ANTENNA DAB( 75Ω ) IN FM(75Ω FM(75 Ω) GND ANALOG OUT DIGITAL OUT COAX. R AM OPT. RDI L SERVICE PORT AC IN OUT EXTERNAL INTERNAL a b c d e a FM antenna terminal (75 ohms) Connect an external FM antenna with a coaxial cable, or a cable network FM source. b AM antenna and ground terminals Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”.
ST7001N 01 Eng 05.7.21 5:23 PM ページ6 ENGLISH PART NAMES AND FUNCTIONS REMOTE CONTROL UNIT For details on the functions of these parts, refer to the pages given in parenthesis (☞ page 10 ~ 27). STANDBY n MEMORY GROUP buttons (A/B, C/D, E/F, G/H, I/J) ON z , 1 2 3 4 5 6 8 9 DIMMER DISPLAY 10 TUNING c v b TE EN R BAND MENU A-PRESET /A-TUNE This button is used for setting the sleep timer. (☞ page 27) ⁄2 ⁄3 ⁄4 A/B C/D E/F G/H I/J T-MODE SLEEP TIMER MEMO n .
ST7001N 01 Eng 05.7.21 5:23 PM ページ7 ENGLISH PART NAMES AND FUNCTIONS 7 Remote control code setting The remote control unit contains 3 sets of remote control codes, and it can be used to control up to 3 tuners in one location. To control a second or third tuner, select the remote control code as explained below. The selected tuner can be operated from the remote control. • When the unit is shipped from the factory, the main unit and remote control are set to TUNER1. 1.
ST7001N 01 Eng 05.7.21 5:23 PM ページ8 ENGLISH CONNECTIONS CONNECTING THE ANTENNA TERMINALS 7 Connecting a DAB outdoor antenna • If good reception cannot be achieved with the included DAB indoor antenna, use a DAB outdoor antenna. Connect an F male type connector to the coaxial cable and connect the antenna to the DAB COAX 75 Ω/ohms terminal. 7 Installing the DAB indoor antenna q DAB station reception (☞ page 18). w Use “Tuning aid” to set position at which reception sensitivity is optimum (☞ page 21).
ST7001N 01 Eng 05.7.21 5:24 PM ページ9 ENGLISH CONNECTIONS Note 7 Connecting the optical output connector • If you want to enjoy listening to the digital output audio of the DAB, connect to an amplifier outfitted with a digital optical or coaxial input. Use an optical digital connecting cable available on the market. Insert the plug firmly in until it clicks into place. Do not bend or bundle the optical digital connecting cable.
ST7001N 01 Eng 05.7.21 5:24 PM ページ10 ENGLISH OPERATION LISTENING TO FM/AM 7 Auto tuning (FM/AM) 7 FM Auto preset memory 1. Press the POWER ON/STANDBY switch q or ON 1. Press the POWER ON/STANDBY switch q or ON 2. Watching the display, press the BAND button c to button , to turn on the power. button , to turn on the power. select the desired band (AM or FM). 2. Watching the display, press the BAND button c to select the FM band. 3. Press the MENU button u or ⁄2 to select menu. 3.
OPERATION 7 Manual tuning (FM/AM) 1. Press the POWER ON/STANDBY switch q or ON button , to turn on the power. 2. Watching the display, press the BAND button c to select the desired band (AM or FM). 3. Press the MENU button u or ⁄2 to select menu. 4. Press the TUNING/PRESET knob !4 or ENTER button 7. While the preset channel number is flashing, either press the TUNING/PRESET knob !4 or MEMO button ⁄6 to store the station in the preset memory. • To preset other channels, repeat steps 2 to 6.
ST7001N 01 Eng 05.7.21 5:24 PM ページ12 ENGLISH OPERATION 7 Recalling preset stations (FM/AM) 7 RDS (Radio Data System) 1. Press the POWER ON/STANDBY switch q or ON • RDS (works only on the FM band) is a broadcasting service which allows station to send additional information along with the regular radio program signal. button , to turn on the power. 2. Watching the display, press the BAND button c to select the desired band (AM or FM). 3. Press the MENU button u or ⁄2 to select menu.
ST7001N 01 Eng 05.7.21 5:24 PM ページ13 7 RDS search ENGLISH OPERATION TUNING/PRESET DAB/FM/AM TUNER ST7001 Use this function to automatically tune to FM stations that provide RDS service. STANDBY SECONDARY TUNED RDS STEREO POWER ON/STANDBY DIMMER DISPLAY MENU AUTO TUNE BAND SELECT PUSH ENTER 1. Press the MENU button u or ⁄2 to select menu. q t u 2. Either turn the TUNING/PRESET knob !4 or press the !4 STANDBY ON CHANNEL/CONTROL button ⁄4 to display “RDS”. 1 2 3 4 5 6 x 7 3.
ST7001N 01 Eng 05.7.21 5:24 PM ページ14 ENGLISH OPERATION 7 PTY search 7 TP search • Use this function to find RDS stations broadcasting a designated program type (PTY). Use this function to find RDS stations broadcasting traffic program (TP). • For a description of each program type, refer to “Program Type (PTY)”. 1. Press the MENU button u or ⁄2 to select menu. 2. Either turn the TUNING/PRESET knob !4 or press the 1. Press the MENU button u or ⁄2 to select menu. 2.
ST7001N 01 Eng 05.7.21 5:24 PM ページ15 7 RT (Radio Text) ENGLISH OPERATION TUNING/PRESET DAB/FM/AM TUNER ST7001 1. Press the MENU button u or ⁄2 to select menu. 2. Either turn the TUNING/PRESET knob !4 or press the STANDBY SECONDARY TUNED RDS STEREO POWER ON/STANDBY DIMMER DISPLAY MENU AUTO TUNE BAND SELECT PUSH ENTER CHANNEL/CONTROL button ⁄4 to display “RDS”. 3. Press the TUNING/PRESET knob !4 or ENTER button u v to set the RDS search selection mode. !4 4.
ST7001N 01 Eng 05.7.21 5:24 PM ページ16 ENGLISH OPERATION 7 CT (Clock Time) 7 Switching RDS information display • You can set clock time automatically by using the RDS stations broadcasting Clock Time (CT) information. 1. Use the procedure described at “Auto tuning”, “Manual This unit picks CT information up and automatically resets itself, when you set “CT ON”. tuning” or “Recalling preset stations” to tune in a frequency with an RDS station. 2. Press the DISPLAY button t or .
ST7001N 01 Eng 05.7.21 5:24 PM ページ17 ENGLISH OPERATION 4. Press the TUNING/PRESET knob !4 or ENTER button v to display the Station Name setting. TUNING/PRESET DAB/FM/AM TUNER ST7001 STANDBY SECONDARY TUNED RDS STEREO POWER ON/STANDBY DIMMER DISPLAY MENU AUTO TUNE BAND SELECT PUSH ENTER t u 5. While “_” is flashing, either turn the TUNING/PRESET !4 knob !4 or press the CHANNEL/CONTROL button ⁄4 to display “M”. 6.
ST7001N 01 Eng 05.7.21 5:24 PM ページ18 ENGLISH OPERATION LISTENING TO DAB BROADCAST 7 About DAB (Digital Audio Broadcasting) • Since the DAB system is broadcasted in digital format, DAB system can supply crystal-clear audio and stable reception even in mobile objects. DAB is a new generation radio which can provide data service and supplementary multi-media services. • DAB broadcasts multiple services under one Ensemble that are called service components.
OPERATION 7 Tuning in DAB (Digital Audio Broadcasting) broadcasts 1. Press the POWER ON/STANDBY switch q or ON 5. Press the TUNING/PRESET knob !4 or ENTER button v to listen to the selected station. • After “Now tuning…” is displayed, the tuned in station appears. button , to turn on the power. 2. Watching the display, press the BAND button c to select the desired band (DAB). 7 Preset stations 1.
ST7001N 01 Eng 05.7.21 5:24 PM ページ20 ENGLISH OPERATION SEARCH MODE TUNING/PRESET DAB/FM/AM TUNER ST7001 7 Sorted list search mode STANDBY SECONDARY TUNED RDS STEREO POWER ON/STANDBY DIMMER DISPLAY MENU AUTO TUNE BAND SELECT PUSH ENTER • You can select any component for listening from the list of sorted components. u • The sorted components are set in the sort mode. (☞ page 22) 1. Press the MENU u or ⁄2 button to select menu. 2.
ST7001N 01 Eng 05.7.21 5:24 PM ページ21 7 Tuning aid ENGLISH OPERATION TUNING/PRESET DAB/FM/AM TUNER ST7001 1. Press the MENU button u or ⁄2 to select menu. 2. Either turn the TUNING/PRESET knob !4 or press the STANDBY SECONDARY TUNED RDS STEREO POWER ON/STANDBY DIMMER DISPLAY MENU AUTO TUNE BAND SELECT PUSH ENTER CHANNEL/CONTROL button ⁄4 to display the search mode selection screen. u !4 STANDBY ON 3. Press the TUNING/PRESET knob !4 or ENTER button v to set the search mode. 4.
ST7001N 01 Eng 05.7.21 5:24 PM ページ22 ENGLISH OPERATION SORT MODE (SORTING COMPONENTS) 5. Press the TUNING/PRESET knob !4 or ENTER button v to set the sort mode to “Sort Mode (S. Component)”. • You can select any component from the sorted list. • You can sort and list scanned components by Alphanumeric, S. component or program type. 7 PTY • You can then select the component you want to listen to from the list. The “S.Component” is sorted in the order of the program Type. 7 Alphanumeric 1.
ST7001N 01 Eng 05.7.21 5:24 PM ページ23 7 Switching the DAB information display ENGLISH OPERATION 7 DRC (Dynamic Range Control) 1. Follow steps 1 to 4 under “Tuning in DAB (Digital Audio • The DRC (Dynamic Range Control) function lets you change the dynamic range of the received sound depending on the content of the broadcast so that the sound is easier to hear even when the volume is low. 2. Press the DISPLAY button t or . to switch the DAB 1. Press the MENU button u or ⁄2 to select menu. 2.
ST7001N 01 Eng 05.7.21 5:24 PM ページ24 SETTING THE CLOCK 7 Present time setting 7 Displaying present time 1. A present time can be displayed for 5 seconds by holding down the TIMER button ⁄7 more than 3 seconds. • To operate the timer program, you must set the present time. The clock time can be set 12-hour or 24-hour system. The clock displays “SUNDAY” “12H SYSTEM” “0:00AM” at initial. 1. Press and hold down the TIMER button ⁄7 until the “CLOCK 0:00AM” is displayed. TUNING/PRESET 2.
OTHER OPERATION TIMER PROGRAMS 3. Press the TUNING/PRESET knob !4 or ENTER button v to select timer program number. 7 About the Timer Programs 4. The display indicate “TIMER PROGRAM x SET”. • This unit has three timer programs so that you can turn it on and off automatically at certain times and on certain days of the week. • Timer programs can be set for single operation (Once) or everyweek operation (Everyweek) or everyday operation (Everyday) or the days of the week operation (Weekday).
ST7001N 01 Eng 05.7.21 5:24 PM ページ26 ENGLISH OTHER OPERATION Use the TUNING/PRESET knob !4 or pressing the CHANNEL/CONTROL button ⁄4 to select the last day. Then press the TUNING/PRESET knob !4 or ENTER button v. 10. Set the On time. 7 Timer program off 1. Press the TIMER button ⁄7, “TIMER PROGRAM 1” is displayed. 2. Either turn the TUNING/PRESET knob !4 or press the CHANNEL/CONTROL button ⁄4 to select timer program number. 3.
ST7001N 01 Eng 05.7.21 5:24 PM ページ27 7 Sleep timer LAST FUNCTION MEMORY • The sleep timer function allows the unit to be in standby mode automatically after specific period of time. 1. Press the SLEEP button m on the remote control. 2. Each press of the button will increase the time before shut down in the following sequence. OFF 10 ENGLISH OTHER OPERATION 20 30 60 90 120 3. The sleep timer will be shown for 5 seconds in the display, and it will count down until the time has elapsed.
ST7001N 01 Eng 05.7.22 2:29 PM ページ28 ENGLISH TROUBLESHOOTING If a problem should arise, first check the following. 1. Are the connections correct? 2. Have you operated the receiver according to the operating instructions? 3. Are the speakers and other components operating properly? If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. Disconnect the power immediately and contact your store of purchase.
SPECIFICATIONS & DIMENSIONAL DRAWINGS Frequency response ................................+0.5/–0.5 dB (5 Hz ~ 20 kHz) Digital output ............................................Optical, Coaxial Sampling frequency ...............................................48 kHz Aerial terminal ...................................75 Ω/ohm, F female Analog output level ................................................2 Vrms FM tuner section Frequency range ..........................87.5 MHz ~ 108.0 MHz Antenna terminals .
ST7001N 01 Eng 05.7.22 9:10 AM ページ30 ENGLISH SPECIFICATIONS & DIMENSIONAL DRAWINGS Band III (174 to 240 MHz) L-Band (1452 to 1490 MHz) Frequency Level Frequency Level 174.928 MHz 176.640 MHz 178.352 MHz 180.064 MHz 181.936 MHz 183.648 MHz 185.360 MHz 187.072 MHz 188.928 MHz 190.640 MHz 192.352 MHz 194.064 MHz 195.936 MHz 197.648 MHz 199.360 MHz 201.072 MHz 202.928 MHz 204.640 MHz 206.352 MHz 5A 5B 5C 5D 6A 6B 6C 6D 7A 7B 7C 7D 8A 8B 8C 8D 9A 9B 9C 208.064 MHz 209.936 MHz 211.648 MHz 213.
ST7001N DFU cover 05.7.21 5:22 PM ページ4 www.marantz.com You can find your nearest authorized distributor or dealer on our website. U.S.A. Marantz America, Inc. 1100 Maplewood Drive, Itasca, IL 60143, U.S.A. EUROPE Marantz Europe B.V. P.O. Box 8744, 5605 LS Eindhoven, The Netherlands is a registered trademark.
