Model SR6001 User Guide AV Surround Receiver SR6001U DFU̲0̲cover.indd I 06.12.
IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
13. 14. 15. 16. 17. 18. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying par ticular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Protective Attachment Plug – The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual for replacement or resetting of protective device.
ENGLISH TABLE OF CONTENTS INTRODUCTION ....................................2 SETUP ..................................................26 BASIC OPERATION (TUNER).............53 PRECAUTIONS ......................................2 ONSCREEN DISPLAY MENU SYSTEM .........................26 LISTENING TO THE TUNER ...........................................53 1 INPUT SETUP .............................................................28 PRESET MEMORY ..........................................................
ENGLISH INTRODUCTION PRECAUTIONS Thank you for purchasing the Marantz SR6001 Surround receiver. This remarkable component has been engineered to provide you with many years of home theater enjoyment. Please take a few minutes to read this manual thoroughly before you connect and operate the SR6001. As there are a number of connection and configuration options, you are encouraged to discuss your own particular home theater setup with your Marantz A/V specialist dealer.
“DTS” and “DTS 96/24” are trademarks of Digital Theater Systems, Inc. Dolby Digital identifies the use of Dolby Digital audio coding for such consumer formats as DVD and DTV. As with film sound, Dolby Digital can provide up to five full-range channels for left, center, and right screen channels, independent left and right surround channels, and a sixth (“.1”) channel for low-frequency effects.
ENGLISH There are several factors that can degrade the sound from even the best loudspeakers in a listening room. One of the most important is the interaction of sound from the loudspeakers with large surfaces such as walls, the floor, and the ceiling in the room. Even with careful loudspeaker placement and acoustical treatments, there are significant problems that are caused by room acoustics.
The SR6001 incorporates the latest generation of digital surround sound decoding technology such as Dolby Digital EX, Dolby Digital, DTS ES (Discrete 6.1 and Matrix 6.1), DTS Neo:6 (Cinema, Music), Dolby Pro-Logic II (Movie, Music and Game), Dolby ProLogic IIx (Movie, Music and Game), Circle Surround II (Cinema, Music and Mono). In addition, Marantz has focused on the future. By utilizing pre-out jacks, 7.
ENGLISH !0 FRONT PANEL q w e !6 MEMORY button Press this button to enter the tuner preset memory numbers or station names. (See page 54) r ty u io!0 !1 !2 !3 !4 !1 !7 CLEAR button Press this button to cancel the station-memory setting mode or preset scan tuning. (See page 55) HT-EQ button Press this button to switch between HT-EQ ON/Off. 7.1CH INPUT button Press this button to select the output of an external multichannel player.
s AV d DISP MULTI SE LE h g AUTO TUNED AUTO SURR DIRECT k ¡0 ¡1 ¡3 ¡2 l j ST V – OFF DISC 6.1 PEAK ATT ANALOG SURROUND SPKR A B EQ DIGITAL DIGITAL NIGHT MT X 6.1 ¡4 L SUR RO UT f a SLEEP INP PCM This indicator is illuminated when the input signal is PCM (pulse code modulation). 2 SURROUND This indicator is illuminated when a Dolby Surround signal is input.
ENGLISH u REAR PANEL q e w r ty u INPUT 2(DVD) INPUT 1(TV) GND AM INPUT 1(DVD) @1 CR/ PR CB/ Y INPUT 3(VCR) PB CR/ PR Y CB/ PB CR/ INPUT 2(DSS) VCR(3) IN R PR INPUT 4(DSS) RS-232C i OUTPUT MULTI SPEAKER / SPEAKER C XM DVD(2) L R DSS(4) TV(1) MONITOR VCR(3) DVD(2) DSS(4) L AC IN MONI.
AUDIO IN/OUT (TV, DVD, VCR, DSS, TAPE, CD/CDR) These are the analog audio inputs and outputs. There are 6 audio inputs and 3 audio outputs. The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The audio inputs and outputs require RCA-type connectors. @0 DIGITAL INPUT (Dig.1 - 5) / OUTPUT (coaxial, optical) These are the digital audio inputs and outputs. There are 2 digital inputs with coaxial jacks, 3 with optical jacks.
ENGLISH ⁄3 CONTROL buttons ¤1 BAND/LIP SYNC/INPUT button ¤6 VOLUME +/- buttons These buttons are used when operating PLAY, STOP, PAUSE and other commands of a source. (When TUNER mode is selected) Used to select a radio band. This button is used to adjust the volume for the amplifier and television. (When TUNER mode is selected) (When AMP mode is selected) Used to select LIP SYNC mode. Note: Set the AMP mode to use this button with the SR6001. T.
REMOTE CONTROL The distance between the transmitter of the remote control and the IR SENSOR of the SR6001 should be less than 5 meters. If the remote control is pointed in a direction other than the IR SENSOR or if there is an obstacle between them, use of the remote control may not be possible. LOADING BATTERIES CAUTIONS ON BATTERIES The life of the batteries used with the remote control is about 4 months with normal use.
ENGLISH GENERAL INFORMATION OF RC5001SR TO SR6001 To control the SR6001 by your RC5001SR, you have to select the device AMP or TUNER by pressing the SOURCE button. Please refer below for the details in AMP and TUNER mode. AMP MODE TUNER MODE LEARN SOURCE SEND SET OFF ON DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT l/ SLEEP AUTO 1 2 3 BAND EX/ES VIRTUAL T.MODE 5 6 STEREO NIGHT CS 4 M-CH ST 7 8 9 7.1CH IN A/D 0 +10 CL CH/ CAT P.
1. 2. ENGLISH CONTROLLING MARANTZ COMPONENTS Press the desired SOURCE button. Press the desired operation buttons to play the selected component. • For details, refer to the component’s user guide. • It may not be possible to operate some models. CONTROLLING A MARANTZ DVD PLAYER (DVD MODE) LEARN SOURCE SEND SET OFF ON DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT l/ SLEEP AUTO 1 2 3 BAND T.MODE EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 CS 7.
ENGLISH CONTROLLING A MARANTZ CD RECORDER (CDR MODE) LEARN SOURCE SEND SET OFF ON DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT l/ SLEEP AUTO 1 CS 2 3 BAND EX/ES VIRTUAL T.MODE 4 5 6 M-CH ST STEREO NIGHT 7 8 9 7.1CH IN A/D 0 +10 CL CH/ CAT P.
NORMAL MODE (When operating Marantz AV equipment products) This remote control is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD, CD-R, MD, TAPE (tape deck), AUX1, AUX2, and AMP (amplifier). Learning is not necessary for Marantz products. You can use these products without setting any codes. Importants: • Some codes may be not match your equipment.
ENGLISH LEARN MODE 4. This remote control is capable of learning and storing codes used by other remote controls that you already own. For codes which are not learned, the remote control will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer’s AV equipment which is set by the customer. The receiver sensor for the remote control signals is located at the top of the remote control. 1. DISPLAY AUTO 1 CS 4 5. 6.
SPEAKER PLACEMENT The ideal surround speaker system for this unit is 7speaker systems, using front left and right speakers, a center speaker, surround left and right speakers, a surround back left and right speakers, and a subwoofer. For best results we recommend that all front speakers be of the same type, with identical or similar driver units. This will deliver smooth pans across the front sound stage as the action moves from side to side.
CONNECTING AUDIO COMPONENTS Tape Deck CD recorder / MD deck OUT IN OUT IN L L R R L R DIGITAL INPUT DIGITAL OUTPUT L R R L R L R L R L R Analog Audio R L INPUT 2(DVD) INPUT 1(TV) OUTPUT Note: • Be sure to connect the positive and negative cables for the speaker properly. If they are miss-connected, the signal phase will be reversed and the signal quality will be corrupted.
This SR6001 has two HDMI inputs and one HDMI output. The unit can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed. The SR6001 is also capable of converting analog video signals (Composite Video, S-Video, Component Video) for HDMI output. Select an input source from the OSD menu system.
ENGLISH VIDEO, S-VIDEO, COMPONENT JACKS CONNECTING VIDEO COMPONENTS There are 3 types of video jacks on the rear panel. DVD player COMPONENT VIDEO OUT VIDEO OUT DIGITAL AUDIO OUT OUT Y COMPONENT VIDEO IN S-VIDEO OUT CB / PB CR / PR Y CB / PB CR / PR S-VIDEO IN VIDEO PROJECTOR VIDEO jack The video signal for the VIDEO jacks is the conventional composite video signal.
CONNECTING THE REMOTE CONTROL JACKS ENGLISH ADVANCED CONNECTING INPUT 2(DVD) INPUT 1(TV) OUTPUT FM (75) R L GND AM ANTENNA R L R L CB/ PB Y COMPONENT VIDEO INPUT 1(DVD) CR/ CB/ Y PR INPUT 3(VCR) PB CR/ PR CB/ PB Y CR/ PR INPUT 4(DSS) INPUT 2(DSS) OUTPUT HDMI Ver1.
ENGLISH CONNECTING THE SUPPLIED ANTENNAS CONNECTING THE ANTENNA TERMINALS FM Antenna AM Loop Antenna FM External Antenna INPUT 2(DVD) INPUT 1(TV) MODEL NO. SR6001 OUTPUT FM (75) GND AM CR/ CB/ Y PR INPUT 3(VCR) PB CR/ PR Y CB/ PB CR/ INPUT 4(DSS) INPUT 2(DSS) VCR(3) IN L R R PR RS-232C OUTPUT MULTI SPEAKER / SPEAKER C XM DVD(2) L FRONT A CB/ PB Y HDMI Ver1.
SR6001 is the XM Ready® receiver. You can receive XM Satellite Radio® by connecting to the XM Mini-Tuner and Home Dock (sold separately) and subscribing the XM service. Introducing XM Satellite Radio There’s a world of audio listening pleasure beyond AM and FM.
ENGLISH CONNECTING FOR SPEAKER C USE CONNECTING FOR THE MULTI ROOM (Multi room speaker) RIGHT SPEAKER MODEL NO. SR6001 OUTPUT GND AM INPUT 1(DVD) CR/ PR CB/ Y INPUT 3(VCR) PB CR/ PR Y CB/ PB CR/ L R R PR INPUT 4(DSS) INPUT 2(DSS) RS-232C OUTPUT MULTI SPEAKER / SPEAKER C XM VCR(3) IN L FRONT A CB/ PB Y HDMI Ver1.
ENGLISH CONNECTING OTHER EQUIPMENT a INPUT 2(DVD) INPUT 1(TV) MODEL NO. SR6001 OUTPUT SURROUND BACK L MPONENT VIDEO CB/ PB Y CR/ PR CB/ Y INPUT 3(VCR) PB CR/ PR Y CB/ PB CR/ PR INPUT 4(DSS) R RS-232C OUTPUT DMI er1.2 MULTI SPEAKER / SPEAKER C XM 4) TV(1) MONITOR DVD(2) VCR(3) DSS(4) AC IN MONI. OUT OUT IN DC OUT RC-5 MULTI RC S-VIDEO OUT L SL SBL C ON AX. OFF IN PRE OUT FLASHER IN T. UNSWITCHED 1.
ENGLISH SETUP RC5001SR BUTTON CONTROL After all components are connected, initial setup must be performed. MULTI/ CAT M-SPKR UP button ONSCREEN DISPLAY MENU SYSTEM MENU INFO The SR6001 incorporates an onscreen menu system, which makes various operations possible by using the cursor (3, 4, 1 , 2) and ENTER buttons on the remote control unit or on the front panel. MENU button Press this button to display the OSD menu system.
ENGLISH Note: • After you complete this portion of the setup, move cursor to “RETURN” with the 3, 4, 1 and 2 cursor buttons and press the ENTER button. MAIN MENU MAIN MENU 1.INPUT SETUP 2.SPKR SETUP 3.SURR SETUP 4.VIDEO SETUP 5.PREFERENCE 6.ACOUSTIC EQ RETURN LOCKED UNLOCK NEXT EXIT SUB MENU 1.INPUT FUNC INPUT 7.1CH SETUP SETUP INPUT FUNCTION 3.SURR 5.PREFERENCE CHANNEL LEVEL PL x MUSIC PARAMETER CS PARAMETER NEO:6 PARAMETER SETUP RENAME HT-EQ LFE LEVEL RETURN NEXT EXIT “1.
ENGLISH 1.INPUT 1 INPUT SETUP FUNC This menu is for setting the matching the output of connected audio devices and the input jacks of this receiver. 7.1CH • FUNC RENAME : “1-3 FUNCTION RENAME” (see page 30) 1. Select “1. INPUT SETUP” from the MAIN MENU with 3 or 4 cursor button, and press the ENTER button. 1.INPUT FUNC 7.1CH INPUT INPUT FUNCTION RETURN SETUP ☞ P. 29 NEXT EXIT ☞ P.
The 5 and F (Front) digital inputs can be assigned to a desired source. HDMI and COMPONENT inputs can be assigned to the preferred source. Use this menu to select which digital input jacks are to be assigned to which input source. 1. Select “FUNC INPUT SETUP” from the 1.INPUT SETUP menu with the 3 or 4 cursor buttons and press the ENTER button. FUNC INPUT SETUP 1 F U N C : M O D E DIG HDMI COMP V/S TV DVD VCR DSS AUX1 :AUTO :AUTO :AUTO :AUTO :AUTO RETURN 2.
ENGLISH 1-3 FUNCTION RENAME 9. Input sources can be registered under any name. This menu is for renaming input source. This menu is for renaming function name. Names can be up to 10 characters long, including spaces. (Characters are selected from those appearing on the display.) This name appears on the receiver's FL display and the OSD, but it does not appear in the OSD Setup menu. 1. Select “FUNCTION RENAME” from the 1. INPUT SETUP menu with the 3 or 4 cursor buttons and press the ENTER button.
After you have installed the SR6001 connected all the components and determined the speaker layout, it is now time to perform the settings in the Speaker Setup menu for the optimum sound acoustics for your environment and speaker layout. Before you perform the following settings, it is important that you first determine the following characteristics: • AUTO SETUP: “2-1 AUTO SETUP (MultEQ Setup)” (see page 32) • MANUAL SETUP: “2-2 MANUAL SETUP” (see page 35) 1. Select “2.
ENGLISH 2-1 AUTO SETUP (MultEQ™ SETUP) The AUTO SETUP (MultEQ™ Setup) feature of the SR6001 measures sound characteristics of the speaker system and room where the receiver is used and automatically optimizes settings. The Audyssey MultEQ™ technology adopted by the SR6001 provides the best listening environment for multiple listeners. To do this, the AUTO SETUP feature measures a test tone emitted by each channel in a maximum of 6 listening positions, using the supplied microphone.
8. Move the microphone to the second listening position, select “START” with the 3/4 cursor buttons and press the ENTER button to measure the second point. At this point, you can cancel second point measurement and calculate measurement results by selecting “CALCULATE” and pressing the ENTER button. AUTO SPEAKERS 2ND SETUP CHECK:OK When calculations for the measurement results end, a screen appears for confirming the calculation results.
ENGLISH ERROR MESSAGES Displayed Error Cause MIC SET ERROR!! AUTO AUTO SETUP: START 2CH MIC SET AUTO SETUP SPEAKERS • During measurement, turn off devices that make noise such as air conditioners. • Measure at a time when the surrounding area is quiet. • The speakers required for suitable playback were not detected. • Speaker polarity is connected backwards. • Check the speaker that is indicated as having reversed polarity ([REV] can appear with some speakers even when properly connected.
1. Select “2. SPKR SETUP” from the MAIN MENU. 2. Select “MANUAL SETUP” with the 3 or 4 cursor buttons. 3. Press the ENTER button to enter the selection. SPEAKER SIZE INI.SET SPKR: YES SUB W : YES FRONT : SMALL CENTER : SMALL SURR. : SMALL SURR.B : 2CH SURR.B SIZE : SMALL LPF/HPF : 80Hz BASS MIX : RETURN NEXT EXIT When setting the speaker size in the SPEAKER SIZE menu, use the guidelines below. INI.
ENGLISH SUB W: Set the distance from the subwoofer to your normal listening position. SURR. B L: Set the distance from the surround back left speaker to your normal listening position. SURR. B R: Set the distance from the surround back right speaker to your normal listening position. Notes: • Set the distance to each speaker in meters (m) or feet (ft) as follows. m: 0.03 - 9.15 m in 0.03 m steps ft: 0.1 - 30.0 ft in 0.1 ft steps (The values appearing on the FL display are approximate.
This menu is for setting surround effect parameters for the various surround input signals so as to bring out the live audio effect of your speaker system. • CHANNEL LEVEL: “3-1 CHANNEL LEVEL” (see page 37) • PLIIx MUSIC PARAMETER: “3-2 PLIIx MUSIC PARAMETER” (see page 38) • CSII PARAMETER: “3-3 CSII PARAMETER” (see page 38) • NEO:6 PARAMETER: “3-4 NEO:6 PARAMETER” (see page 38) 1. 2. Select “3. SURR SETUP” from the MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button.
ENGLISH SUB W LEVEL: Set the effect level of the subwoofer speaker between –18 and +12 level in 0.5 level interval . • If “NONE” was selected for the subwoofer speaker setting in the SPEAKER SIZE, then this setting will not appear. Note: • Setting to a mode other than multichannel stereo or CSII will affect the speaker level as explained in “2-2 MANUAL SETUP”.
Video settings are made as follows. 1. Select “4. VIDEO SETUP” from the MAIN MENU with the 3/4 cursor buttons and press the ENTER button. 4.VIDEO VIDEO SETUP The SR6001 is equipped to convert video signals for monitor output. This section explains how to set up conversion for each type of video input. 1. Select “4. VIDEO SETUP” from the MAIN MENU with the 3 / 4 cursor buttons and press the ENTER button. 2. Select “VIDEO CONVERT” with the 3 / 4 cursor buttons and press the ENTER button. CONVERT TV.
ENGLISH 5.PREFERENCE 5 PREFERENCE MULTI ROOM DC TRIGGER • MULTI ROOM SETUP : “5-1 MULTI ROOM SETUP” (see page 41) • DC TRIGGER SETUP : “5-2 DC TRIGGER SETUP” (see page 41) 1. STANDBY : BILINGUAL : HDMI AUDIO: RETURN Select “5. PREFERENCE” from MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. DC 5.PREFERENCE MULTI ROOM DC TRIGGER STANDBY : BILINGUAL : HDMI AUDIO: SETUP SETUP NORMAL MAIN ENABLE DC TRIGGER SETUP TRIG:DISABLE TV DVD VCR DSS AUX1 RETURN RETURN 2.
The SR6001 has source selectors, sleep timers and multispeaker output remote control units for the other rooms in the multi room system. These features can be set from this menu. 1. Select “5. PREFERENCE” from the MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. 2. Select “MULTI ROOM SETUP” with the 3 or 4 cursor buttons. 3. Press the ENTER button to enter the setting. LEVEL (VOLUME LEVEL): Adjust the multiroom output level with the 1 or 2 cursor buttons.
ENGLISH 3. 6 ACOUSTIC EQ This display is for setting up the equalizer and changing the Equalizer mode. • PRESET G. EQ ADJ : “6-1 PRESET G. EQ ADJ” (see page 43) • CHECK AUTO : “6-2 CHECK AUTO” (see page 43) EQ MODE: There are 4 equalizer modes to choose from: PRESET G. EQ that allows the user to manually adjust the equalizer, and AUDYSSEY, FRONT and FLAT that automatically adjust the equalizer from the measurement results of the AUTO SETUP feature (see page 32).
6-2 CHECK AUTO These modes allow you to set a 9-band graphic equalizer for each of the 7 channels. These menus are for confirming the results of AUTO SETUP function equalizer measurement (AUDYSSEY, FRONT, FLAT). 1. Select “6. ACOUSTIC EQ” from MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. 2. 3. 1. Select “6. ACOUSTIC EQ” from MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. Select “PRESET G. EQ ADJ” with the 3 or 4 cursor buttons. 2.
ENGLISH BASIC OPERATION ADJUSTING THE MAIN VOLUME SELECTING THE SURROUND MODE Example: AUTO SURROUND (PLAY BACK) READY 7.1CH IN A/D HT-EQ 0 +10 MEMO SPKR A/B MUTE MULTI/ CAT M-SPKR VOLUME CL SOURCE SET OFF ON l/ AV SURROUND RECEIVER SR6001 EAK ATT ANALOG GHT EQ DIGITAL SLEEP SELECTING AN INPUT SOURCE DISPLAY P.
ANALOG VIDEO CONVERSION CONNECTION EXAMPLE • When a monitor is connected to the HDMI MONITOR OUT terminal of the SR6001 • When a monitor is connected to the COMPONENT VIDEO MONITOR OUT terminal of the SR6001 TEMPORARILY TURNING OFF THE SOUND AV SURROUND RECEIVER SR6001 CL DOWN UP-CONVERSION FROM ANALOG VIDEO SIGNALS TO HDMI The up-conversion feature of the SR6001 can output the input analog video signals (for component video signals of 480i, 480p, 1080i and 720p resolution, and S-Video and Video (comp
ENGLISH SURROUND MODE SURROUND The SR6001 is equipped with many surround modes. These are provided to reproduce a variety of surround sound effects, according to the content of the source to be played. The available surround modes may be restricted depending on the input signal and speaker setup. SOURCE DIRECT In the Source Direct mode, the tone control circuit Acoustic EQ. and bass management configuration are bypassed for full-range frequency response and the purist audio reproduction.
STEREO Note: • The Neo:6 mode is available for 2 channel input signals which are encoded in Dolby Digital, HDCD or PCM format. CAUTION MULTI CH. (MOVIE, MUSIC) This mode is used to create a wider, deeper and more natural soundstage from two channel source material. This is done by feeding the left channel signal to both the left front and left surround speakers and the right channel signal to both the right front and right surround speakers.
ENGLISH The relationship between the selected surround mode and the input signal The surround mode is selected with the surround mode selector on the SR6001 or the remote control unit. However, the sound you hear is subject to the relationship between the selected surround mode and the input signal. That relationship is as follows: Surround Mode Input Signal Decoding AUTO Dolby Surr.EX Dolby D (5.1ch) Dolby D (2ch) Dolby D (2ch Surr) DTS-ES DTS 96/24 DTS (5.1ch) Multi Ch-PCM Multi Ch-PCM 96kHz DSD (5.
Input Signal Decoding Dolby Virtual Speaker Dolby Surr.EX Dolby D (5.1ch) Dolby D (2ch) Dolby D (2ch Surr) DTS-ES DTS 96/24 DTS (5.1ch) Multi Ch-PCM DSD (5.1ch) DSD (2ch) PCM (Audio) HDCD Analog Dolby Surr.EX Dolby D (5.1ch) Dolby D (2ch) Dolby D (2ch Surr) DTS-ES DTS 96/24 DTS (5.1ch) Multi Ch-PCM Multi Ch-PCM 96kHz DSD (5.1ch) DSD (2ch) PCM (Audio) HDCD Analog Dolby Surr.EX Dolby D (5.1ch) Dolby D (2ch) Dolby D (2ch Surr) DTS-ES DTS 96/24 DTS (5.1ch) Multi Ch-PCM DSD (5.
ENGLISH OTHER FUNCTION ATTENUATION TO ANALOG INPUT SIGNAL REC TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the SR6001. AUTO POWER ON 1. 2. 3. Be sure the TV auto mode is ENABLED. (Refer to page 39: PREFERENCE) Connect your TV TUNER (etc) to the TVVIDEO in terminal. Be sure to connect the VIDEO input. Turn OFF the power to the TV TUNER and the SR6001. 4. Turn ON the TV TUNER and tune in a receivable station. 5.
SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT AV SURROUND RECEIVER SR6001 LEARN PURE DIRECT DISP SLEEP MULTI AUTO AUTO SURR TUNED DIRECT ST SPKR A B DISC 6.1 V-OFF MT X 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL TUNER SURROUND C SL S SOURCE SR SET OFF MD TAPE DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT AUX1 AUX2 AMP MULTI AUTO MULTI SPEAKER BAND 7.
ENGLISH 7.1 CH INPUT The SR6001 is equipped for future expansion through the use of Multi channel Super Audio CD multichannel player or DVD-Audio player. When this is selected, the input signals connected to the L(front left), R (front right), CENTER, SL (surround left), SR (surround right) and SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH.
(TUNER) To operate the unit from the remote control, press the TUNER button on the remote control so that the tuner mode is engaged. LISTENING TO THE TUNER (Using the SR6001) (Using the SR6001) 1. Turn the INPUT SELECTOR knob to select “TUNER”. 1. 2. Press the BAND button to select either FM or AM. 2. Press the BAND button to select either FM or AM. 3. Press the 3 or 4 cursor buttons on the front Panel for more than 1 second to start the auto tuning function. 3.
ENGLISH MANUAL PRESET MEMORY PRESET MEMORY With this unit you can preset up to 60 FM/AM stations in any order. For each station, you can memorize the frequency and reception mode if desired. 3. 2. 4. SLEEP DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT AUTO 1 SLEEP MULTI AUTO AUTO SURR TUNED DIRECT ST SPKR A B DISC 6.1 V-OFF MTX 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL SL OUND DE C R LFE PCM S CS 3.
2. 3. SLEEP SPKR A B V-OFF MTX 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL SURROUND C 2. SL S dts AUTO SURR TUNED DIRECT ST SPKR A B DISC 6.1 V-OFF MTX 6.1 PEAK NIGHT ATT ANALOG EQ DIGITAL SURROUND DIGITAL C R LFE PCM SL S SR LIP SYNC/ INPUT 2 3 BAND EX/ES VIRTUAL T.MODE DOWN SURROUND 5 6 STEREO NIGHT 7 8 9 7.1CH IN A/D HT-EQ 0 +10 MEMO SPKR A/B MUTE UP MODE AUTO PURE DIRECT HT-EQ MULTI SPEAKER BAND T-MODE MEMORY 4.
ENGLISH CHECKING THE XM SIGNAL STRENGTH AND RADIO ID LISTENING TO XM SATELLITE RADIO SELECTING AN INPUT SOURCE ENTER T.TONE /SET UP Before you can listen to XM Satellite Radio, you must first select the input source on the SR6001. SOURCE SET OFF ON DISPLAY P.DIRECT SURROUND T.DISP PRESET + PTY - 1. DISC+ AUTO 1 M-CH ST 3 BAND VIRTUAL T.MODE 5 6 STEREO ANGLE Select channel 0 (XM000) with the 3 or 4 cursor buttons of the SR6001 or the Q or R buttons of the remote control unit.
2. N A M E / T I T L E Press the INFO button.The following information display will be output. VIDEO AUDIO P i n k F l o i d :DVD :XM / / 1. You can search for the channel you want to listen to using one of three search modes. You can also enter the number directly to select the desired channel.
ENGLISH CATEGORY SEARCH MODE CHANNEL DIRECT CALL You can select the desired channel from the category allocated to each channel. Category being aired can be only selected. You can select the desired channel by directly tapping the numeric keypads on the remote control unit. SOURCE SET OFF ON DISPLAY P.DIRECT SURROUND l/ 0 +10 SPKR A/B MUTE CL CH/ CAT SLEEP MEMO VOLUME MULTI/ CAT M-SPKR INFO DIRECT DISP SLEEP MULTI AUTO AUTO SURR TUNED DIRECT ST SPKR A B DISC 6.1 V-OFF MT X 6.
CLEARING STORED PRESET STATIONS CS EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 CH/ CAT P.SCAN 9 7.1CH IN A/D 0 +10 SPKR A/B MUTE MULTI/ CAT M-SPKR CL You can remove preset stations from the memory using the following procedure. T.MODE HT-EQ MEMO 2. 5 2. 3. AUTO VOLUME 1 CS V ST SPKR A B DISC 6.1 V-OFF MTX 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL C 3 EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 SURROUND DIGITAL L AAC dts 2 8 9 7.
ENGLISH MULTI ROOM SYSTEM 2. The Multiroom System mode allows the same source or different sources to be heard in two rooms other than where this receiver is installed. 1. 4. 3. READY VOLUME DISP SLEEP MULTI AUTO AUTO SURR TUNED ST DIRECT SPKR A B DISC 6.1 V-OFF MT X 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL SURROUND DIGITAL L AAC R C LFE PCM SL DSD S SR DOWN SURROUND UP MULTI MODE AUTO PURE DIRECT HT-EQ SPEAKER MULTI BAND 7.
General: Controlling volume level, sleep timer, and muting. SeIecting input audio and video source. Multi Room output can be operated from a room where the receiver is not installed. This requires a separately sold IR receiver. (For connections, see page 24.) Tuner: Selecting band, controlling preset channel up and down, tuning up and down direct frequency call. 0 CH/ CAT +10 BASS VOLUME SPKR A/B MUTE MULTI/ CAT M-SPKR INFO MENU 2. 1.
ENGLISH TROUBLESHOOTING In case of trouble, check the following before calling for service: 1. 2. 3. Are the connections made properly ? Are you operating the unit properly following the user’s guide ? Are the power amplifiers and speaker working properly ? If the unit does not operate properly, check items shown in the following table.
TROUBLESHOOTING ENGLISH HDMI If a problem should arise, first check the following. SYMPTOM CAUSE The display does not appear over an HDMI connection. The connected monitor or projector does not support HDCP. REMEDY 1. Are the connections correct? 2. Have you operated the receiver according to the operating instructions? 3. Are the speakers and other components operating properIy? The HDMI input of on the TV is not on. Set HDMI input so that it turns on, as explained in the TV's instruction manual.
disconnect the plug from the AC line supply - after waiting at least three minutes, reconnect the plug to the AC line supply - re-attempt to operate the equipment Memory backup • In case a power outage occurs or the power cord is accidentally unplugged, the SR6001 is equipped with a backup function to prevent memory data such as the preset memory from being erased. HOW TO RESET THE UNIT AUTO AUTO SURR TUNED DIRECT ST SPKR A B DISC 6.1 V-OFF MTX 6.
SETUP CODES TV Acer .......................................................... 1141 Admiral .................................1002, 1009, 1089 Aiko .......................................................... 1059 Aiwa................................................1117, 1118 Akai .......................................................... 1001 Amtron ...................................................... 1023 Anam ........................................................ 1113 Anam National......................
Dimensia ..............................3004, 3063, 3085 Dixon ..............................................3077, 3081 Dynatech .................................................. 3035 Electrohome ............................................. 3052 Electrophonic ........................................... 3052 Emerson .................... 3009, 3015, 3016, 3017 3018, 3019, 3022, 3035 3047, 3052, 3054, 3073 Fisher .............................................3029, 3032 Fuji.....................................
Hughes ...........................................4001, 4016 Janeil ........................................................ 4025 JVC........................................................... 4017 Mitsubishi ................................................. 4001 Panasonic.......................................4004, 4010 Philips .............................................4031, 4035 Proscan ..................... 4002, 4008, 4009, 4011 Radio Shack ...................................4036, 4037 RCA ..........
www.marantz.com You can find your nearest authorized distributor or dealer on our website. is a registered trademark. Printed in China SR6001U DFU̲5̲Setup.indd iv 12/2006 00M25CW851250 mzh-d 06.12.
