Model SR6001 User Guide AV Surround Receiver SR6001N DFU_0_cover.indd I 06.12.
ENGLISH NEDERLANDS WARRANTY For warranty information, contact your local Marantz distributor. GARANTIE Voor inlichtingen omtrent garantie dient u zich tot uw plaatselijke Marantz. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. UW KWITANTIE, KASSABON E.D. BEWAREN Uw kwitantie, kassabon e.d.
CE MARKING English The SR6001 is in conformity with the EMC directive and low-voltage directive. Français Le SR6001 est conforme à la directive EMC et à la directive sur les basses tensions. Deutsch Das Modell SR6001 entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte. Nederlands De SR6001 voldoet aan de EMC eisen en de vereisten voor laag-voltage. Español El SR6001 está de acuerdo con las normas EMC y las relacionadas con baja tensión.
Nederlands WAARSCHUWINGEN - Stel het apparaat niet bloot aan regen of vocht. - Verwijder de afdekplaat van het apparaat niet. - Duw niets door de ventilatieopeningen in het apparaat. - Raak het netsnoer niet met natte handen aan. - Bedek de ventilatieopeningen niet met enige voorwerpen, zoals tafelkleden, kranten, gordijnen, enz. - Plaats geen brandende voorwerpen, zoals kaarsen, op het apparaat.
ENGLISH TABLE OF CONTENTS FOREWORD ...........................................2 SETUP ..................................................25 BASIC OPERATION (TUNER) .......... 52 EQUIPMENT MAINS WORKING SETTING ......................2 ONSCREEN DISPLAY MENU SYSTEM .........................25 LISTENING TO THE TUNER ...........................................52 COPYRIGHT ......................................................................2 1 INPUT SETUP .................................................
ENGLISH FOREWORD INTRODUCTION This section must be read before any connection is made to the mains supply. Thank you for purchasing the Marantz SR6001 Surround receiver. This remarkable component has been engineered to provide you with many years of home theater enjoyment. Please take a few minutes to read this manual thoroughly before you connect and operate the SR6001.
“DTS” and “DTS 96/24” are trademarks of Digital Theater Systems, Inc. Dolby Digital identifies the use of Dolby Digital audio coding for such consumer formats as DVD and DTV. As with film sound, Dolby Digital can provide up to five full-range channels for left, center, and right screen channels, independent left and right surround channels, and a sixth (“.1”) channel for low-frequency effects.
ENGLISH There are several factors that can degrade the sound from even the best loudspeakers in a listening room. One of the most important is the interaction of sound from the loudspeakers with large surfaces such as walls, the floor, and the ceiling in the room. Even with careful loudspeaker placement and acoustical treatments, there are significant problems that are caused by room acoustics.
The SR6001 incorporates the latest generation of digital surround sound decoding technology such as Dolby Digital EX, Dolby Digital, DTS ES (Discrete 6.1 and Matrix 6.1), DTS Neo:6 (Cinema, Music), Dolby Pro-Logic II (Movie, Music and Game), Dolby ProLogic IIx (Movie, Music and Game), Circle Surround II (Cinema, Music and Mono). In addition, Marantz has focused on the future. By utilizing pre-out jacks, 7.
ENGLISH u FRONT PANEL q w e r ty u io!0 !1 !2 !3 !4 i AV SURROUND RECEIVER SR6001 VOLUME o PURE DIRECT DISP SLEEP MULTI AUTO AUTO SURR TUNED DIRECT ST SPKR A B DISC 6.1 V-OFF MTX 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL SURROUND DIGITAL L AAC C R LFE PCM SL DSD S SR DOWN SURROUND MODE PURE DIRECT UP MULTI AUTO MULTI BAND SPEAKER 7.
SPEAKER A/B button Press this button to select speaker systems A and/or B. s Opening and closing the front panel door When you want to use the controls behind the front panel door, open the door by gently pressing on the lower part of the panel. Keep the door closed when not using these controls. f a d DISP MULTI SLEEP AUTO TUNED AUTO SURR DIRECT SE LE k ¡0 ¡1 ¡3 ¡2 l j ST V – OFF DISC 6.1 PEAK ATT ANALOG SURROUND SPKR A B EQ DIGITAL DIGITAL NIGHT MT X 6.
ENGLISH y REAR PANEL q e w r t AM @1 L R R CR/ PR CB/ Y INPUT 3(VCR) PB CR/ PR Y CB/ PB CR/ PR INPUT 4(DSS) INPUT 2(DSS) RS-232C VCR(3) IN u OUTPUT MULTI SPEAKER / SPEAKER C L AC IN DVD(2) DSS(4) TV(1) MONITOR VCR(3) DVD(2) DSS(4) MONI. OUT FRONT B OUT OUT R IN VIDEO S-VIDEO OUT DC OUT RC-5 MULTI RC DIGITAL OUT DIGITAL IN Two terminals are provided for the front left, and right speakers for multi room (2nd zone) or surround back.
DIGITAL INPUT (Dig.1 - 5) / OUTPUT (coaxial, optical) These are the digital audio inputs and outputs. There are 2 digital inputs with coaxial jacks, 3 with optical jacks. The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component. For digital output, there is 1 coaxial output and 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components.
ENGLISH ⁄3 CONTROL buttons ¤1 BAND/LIP SYNC/INPUT button ¤6 VOLUME +/- buttons These buttons are used when operating PLAY, STOP, PAUSE and other commands of a source. (When TUNER mode is selected) Used to select a radio band. This button is used to adjust the volume for the amplifier and television. (When TUNER mode is selected) (When AMP mode is selected) Used to select LIP SYNC mode. Note: Set the AMP mode to use this button with the SR6001. T.
REMOTE CONTROL The distance between the transmitter of the remote control and the IR SENSOR of the SR6001 should be less than 5 meters. If the remote control is pointed in a direction other than the IR SENSOR or if there is an obstacle between them, use of the remote control may not be possible. LOADING BATTERIES CAUTIONS ON BATTERIES The life of the batteries used with the remote control is about 4 months with normal use.
ENGLISH GENERAL INFORMATION OF RC5001SR TO SR6001 To control the SR6001 by your RC5001SR, you have to select the device AMP or TUNER by pressing the SOURCE button. Please refer below for the details in AMP and TUNER mode. AMP MODE TUNER MODE LEARN SOURCE SEND SET OFF ON DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT l/ SLEEP AUTO 1 2 3 BAND EX/ES VIRTUAL T.MODE 5 6 STEREO NIGHT CS 4 M-CH ST 7 8 9 7.1CH IN A/D 0 +10 CL CH/ CAT P.
1. 2. ENGLISH CONTROLLING MARANTZ COMPONENTS Press the desired SOURCE button. Press the desired operation buttons to play the selected component. • For details, refer to the component’s user guide. • It may not be possible to operate some models. CONTROLLING A MARANTZ DVD PLAYER (DVD MODE) LEARN SOURCE SEND SET OFF ON DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT l/ SLEEP AUTO 1 2 3 BAND T.MODE EX/ES VIRTUAL 4 5 6 M-CH ST STEREO NIGHT 7 8 9 CS 7.
ENGLISH CONTROLLING A MARANTZ CD RECORDER (CDR MODE) LEARN SOURCE SEND SET OFF ON DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT l/ SLEEP AUTO 1 CS 2 3 BAND EX/ES VIRTUAL T.MODE 4 5 6 M-CH ST STEREO NIGHT 7 8 9 7.1CH IN A/D 0 +10 CL CH/ CAT P.
NORMAL MODE (When operating Marantz AV equipment products) This remote control is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD, CD-R, MD, TAPE (tape deck), AUX1, AUX2, and AMP (amplifier). Learning is not necessary for Marantz products. You can use these products without setting any codes. Importants: • Some codes may be not match your equipment.
ENGLISH LEARN MODE 4. This remote control is capable of learning and storing codes used by other remote controls that you already own. For codes which are not learned, the remote control will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer’s AV equipment which is set by the customer. The receiver sensor for the remote control signals is located at the top of the remote control. 1. DISPLAY AUTO 1 CS 4 5. 6.
SPEAKER PLACEMENT The ideal surround speaker system for this unit is 7speaker systems, using front left and right speakers, a center speaker, surround left and right speakers, a surround back left and right speakers, and a subwoofer. For best results we recommend that all front speakers be of the same type, with identical or similar driver units. This will deliver smooth pans across the front sound stage as the action moves from side to side.
CONNECTING AUDIO COMPONENTS Tape Deck CD recorder / MD deck OUT IN OUT IN L L R R L R DIGITAL INPUT DIGITAL OUTPUT L R R L R L R L R L R Analog Audio R L INPUT 2(DVD) INPUT 1(TV) OUTPUT Note: • Be sure to connect the positive and negative cables for the speaker properly. If they are miss-connected, the signal phase will be reversed and the signal quality will be corrupted.
This SR6001 has two HDMI inputs and one HDMI output. The unit can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed. The SR6001 is also capable of converting analog video signals (Composite Video, S-Video, Component Video) for HDMI output. Select an input source from the OSD menu system.
ENGLISH VIDEO, S-VIDEO, COMPONENT JACKS CONNECTING VIDEO COMPONENTS There are 3 types of video jacks on the rear panel. DVD player COMPONENT VIDEO OUT VIDEO OUT DIGITAL AUDIO OUT OUT Y COMPONENT VIDEO IN S-VIDEO OUT CB / PB CR / PR Y CB / PB CR / PR S-VIDEO IN VIDEO PROJECTOR VIDEO jack The video signal for the VIDEO jacks is the conventional composite video signal.
CONNECTING THE REMOTE CONTROL JACKS ENGLISH ADVANCED CONNECTING INPUT 2(DVD) INPUT 1(TV) OUTPUT FM (75) R L GND AM ANTENNA R L R L CB/ PB Y COMPONENT VIDEO INPUT 1(DVD) CR/ CB/ Y PR INPUT 3(VCR) PB CR/ PR CB/ PB Y CR/ PR INPUT 4(DSS) INPUT 2(DSS) OUTPUT HDMI Ver1.
ENGLISH CONNECTING THE SUPPLIED ANTENNAS CONNECTING THE ANTENNA TERMINALS FM Antenna AM Loop Antenna FM External Antenna INPUT 2(DVD) INPUT 1(TV) MODEL NO. SR6001 OUTPUT FM (75) GND AM INPUT 1(DVD) SPEAKER SYSTEMS SURROUND BACK L L R R ANTENNA FRONT A COMPONENT VIDEO CB/ PB Y CR/ CB/ Y PR INPUT 3(VCR) PB CR/ Y PR CB/ PB CR/ PR INPUT 4(DSS) INPUT 2(DSS) RS-232C OUTPUT HDMI Ver1.
(Multi room speaker) RIGHT SPEAKER MODEL NO. SR6001 OUTPUT GND AM INPUT 1(DVD) SPEAKER SYSTEMS SURROUND BACK L L R R ANTENNA FRONT A COMPONENT VIDEO CB/ PB Y CR/ PR CB/ Y INPUT 3(VCR) PB CR/ PR Y CB/ PB CR/ PR INPUT 4(DSS) INPUT 2(DSS) RS-232C OUTPUT HDMI Ver1.2 MULTI SPEAKER / SPEAKER C L AC IN TV(1) DVD(2) VCR(3) IN Notes: • If incorrectly connected, a protective circuit in the receiver will trip and set the receiver to standby. (The STANDBY indicator will flash.
ENGLISH CONNECTING OTHER EQUIPMENT a INPUT 2(DVD) INPUT 1(TV) MODEL NO. SR6001 OUTPUT SURROUND BACK L MPONENT VIDEO CB/ PB Y CR/ PR CB/ Y INPUT 3(VCR) PB CR/ PR Y CB/ PB CR/ PR INPUT 4(DSS) R RS-232C OUTPUT DMI er1.2 MULTI SPEAKER / SPEAKER C AC IN 4) TV(1) MONITOR DVD(2) VCR(3) DSS(4) MONI. OUT OUT IN DC OUT RC-5 MULTI RC S-VIDEO OUT L SL SBL C ON AX. OFF IN PRE OUT FLASHER IN T. OUT TAPE CD/CD-R MULTI R SR SBR SW L SL SBL C 7.
RC5001SR BUTTON CONTROL After all components are connected, initial setup must be performed. MULTI/ CAT ENGLISH SETUP M-SPKR UP button ONSCREEN DISPLAY MENU SYSTEM MENU INFO The SR6001 incorporates an onscreen menu system, which makes various operations possible by using the cursor (3, 4, 1 , 2) and ENTER buttons on the remote control unit or on the front panel. MENU button Press this button to display the OSD menu system.
ENGLISH Note: • After you complete this portion of the setup, move cursor to “RETURN” with the 3, 4, 1 and 2 cursor buttons and press the ENTER button. MAIN MENU MAIN MENU 1.INPUT SETUP 2.SPKR SETUP 3.SURR SETUP 4.VIDEO SETUP 5.PREFERENCE 6.ACOUSTIC EQ RETURN LOCKED UNLOCK NEXT EXIT SUB MENU 1.INPUT FUNC INPUT 7.1CH SETUP SETUP INPUT FUNCTION 3.SURR 5.PREFERENCE CHANNEL LEVEL PL x MUSIC PARAMETER CS PARAMETER NEO:6 PARAMETER SETUP RENAME HT-EQ LFE LEVEL RETURN NEXT EXIT “1.
FUNC This menu is for setting the matching the output of connected audio devices and the input jacks of this receiver. 7.1CH • FUNC RENAME : “1-3 FUNCTION RENAME” (see page 29) 1. Select “1. INPUT SETUP” from the MAIN MENU with 3 or 4 cursor button, and press the ENTER button. 1.INPUT FUNC INPUT 7.1CH INPUT FUNCTION RETURN SETUP ☞ P. 28 NEXT EXIT ☞ P.
ENGLISH 1-1 FUNC INPUT SETUP (ASSIGNABLE DIGITAL INPUT) The 5 and F (Front) digital inputs can be assigned to a desired source. HDMI and COMPONENT inputs can be assigned to the preferred source. Use this menu to select which digital input jacks are to be assigned to which input source. 1. Select “FUNC INPUT SETUP” from the 1.INPUT SETUP menu with the 3 or 4 cursor buttons and press the ENTER button.
9. Input sources can be registered under any name. This menu is for renaming input source. This menu is for renaming function name. Names can be up to 10 characters long, including spaces. (Characters are selected from those appearing on the display.) This name appears on the receiver's FL display and the OSD, but it does not appear in the OSD Setup menu. 1. Select “FUNCTION RENAME” from the 1. INPUT SETUP menu with the 3 or 4 cursor buttons and press the ENTER button.
ENGLISH 2.SPKR 2 SPKR (SPEAKER) SETUP After you have installed the SR6001 connected all the components and determined the speaker layout, it is now time to perform the settings in the Speaker Setup menu for the optimum sound acoustics for your environment and speaker layout. Before you perform the following settings, it is important that you first determine the following characteristics: • AUTO SETUP: “2-1 AUTO SETUP (MultEQ Setup)” (see page 31) • MANUAL SETUP: “2-2 MANUAL SETUP” (see page 34) 1.
The AUTO SETUP (MultEQ™ Setup) feature of the SR6001 measures sound characteristics of the speaker system and room where the receiver is used and automatically optimizes settings. The Audyssey MultEQ™ technology adopted by the SR6001 provides the best listening environment for multiple listeners. To do this, the AUTO SETUP feature measures a test tone emitted by each channel in a maximum of 6 listening positions, using the supplied microphone.
ENGLISH 8. 8. Move the microphone to the second listening position, select “START” with the 3/4 cursor buttons and press the ENTER button to measure the second point. At this point, you can cancel second point measurement and calculate measurement results by selecting “CALCULATE” and pressing the ENTER button. AUTO SPEAKERS 2ND SETUP CHECK:OK When calculations for the measurement results end, a screen appears for confirming the calculation results.
Displayed Error Cause MIC SET ERROR!! AUTO AUTO SETUP: START 2CH MIC SET AUTO SETUP SPEAKERS • During measurement, turn off devices that make noise such as air conditioners. • Measure at a time when the surrounding area is quiet. • The speakers required for suitable playback were not detected. • Speaker polarity is connected backwards. • Check the speaker that is indicated as having reversed polarity ([REV] can appear with some speakers even when properly connected.
ENGLISH 2-2 MANUAL SETUP 1. Select “2. SPKR SETUP” from the MAIN MENU. 2. Select “MANUAL SETUP” with the 3 or 4 cursor buttons. 3. Press the ENTER button to enter the selection. SPEAKER SIZE INI.SET SPKR: YES SUB W : YES FRONT : SMALL CENTER : SMALL SURR. : SMALL SURR.B : 2CH SURR.B SIZE : SMALL LPF/HPF : 80Hz BASS MIX : RETURN NEXT EXIT When setting the speaker size in the SPEAKER SIZE menu, use the guidelines below. INI.
Notes: • Set the distance to each speaker in meters (m) or feet (ft) as follows. m: 0.03 - 9.15 m in 0.03 m steps ft: 0.1 - 30.0 ft in 0.1 ft steps (The values appearing on the FL display are approximate.) • For the speakers that you have selected “NONE” the speaker size menu will not appear. • The setting for surr.back L and surr.back R appears if it is set, two surround back speakers in the SPEAKER SIZE menu. • The setting of SURR.
ENGLISH 3.SURR 3 SURROUND SETUP This menu is for setting surround effect parameters for the various surround input signals so as to bring out the live audio effect of your speaker system. • CHANNEL LEVEL: “3-1 CHANNEL LEVEL” (see page 36) • PLIIx MUSIC PARAMETER: “3-2 PLIIx MUSIC PARAMETER” (see page 37) • CSII PARAMETER: “3-3 CSII PARAMETER” (see page 37) • NEO:6 PARAMETER: “3-4 NEO:6 PARAMETER” (see page 37) 1. 2. Select “3.
Note: • Setting to a mode other than multichannel stereo or CSII will affect the speaker level as explained in “2-2 MANUAL SETUP”. After you complete this portion of the setup, move the cursor to “RETURN” with the 3, 4, 1 and 2 cursor buttons and press the ENTER button to go to the 3. SURR SETUP menu. 3-2 PLIIx (PRO LOGIC IIx) MUSIC PARAMETER Pro LogicIIx-Music mode creates a rich and enveloping surround ambience from stereo sources such as CDs.
ENGLISH 4-1 VIDEO CONVERT 4 VIDEO SETUP Video settings are made as follows. 1. Select “4. VIDEO SETUP” from the MAIN MENU with the 3/4 cursor buttons and press the ENTER button. 4.VIDEO VIDEO SETUP The SR6001 is equipped to convert video signals for monitor output. This section explains how to set up conversion for each type of video input. 1. Select “4. VIDEO SETUP” from the MAIN MENU with the 3 / 4 cursor buttons and press the ENTER button. 2.
MULTI ROOM DC TRIGGER • MULTI ROOM SETUP : “5-1 MULTI ROOM SETUP” (see page 40) • DC TRIGGER SETUP : “5-2 DC TRIGGER SETUP” (see page 40) 1. STANDBY : BILINGUAL : HDMI AUDIO: RETURN Select “5. PREFERENCE” from MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. DC 5.PREFERENCE MULTI ROOM DC TRIGGER STANDBY : BILINGUAL : HDMI AUDIO: SETUP SETUP NORMAL MAIN ENABLE DC TRIGGER SETUP TRIG:DISABLE TV DVD VCR DSS AUX1 RETURN RETURN 2. NEXT : : : : : TAPE CD/R AUX2 TUNER 7.
ENGLISH 5-1 MULTI ROOM SETUP The SR6001 has source selectors, sleep timers and multispeaker output remote control units for the other rooms in the multi room system. These features can be set from this menu. 1. Select “5. PREFERENCE” from the MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. 2. Select “MULTI ROOM SETUP” with the 3 or 4 cursor buttons. 3. Press the ENTER button to enter the setting.
This display is for setting up the equalizer and changing the Equalizer mode. • PRESET G. EQ ADJ : “6-1 PRESET G. EQ ADJ” (see page 42) • CHECK AUTO : “6-2 CHECK AUTO” (see page 42) EQ MODE: There are 4 equalizer modes to choose from: PRESET G. EQ that allows the user to manually adjust the equalizer, and AUDYSSEY, FRONT and FLAT that automatically adjust the equalizer from the measurement results of the AUTO SETUP feature (see page 31). ENGLISH 3.
ENGLISH 6-1 PRESET G. EQ ADJ 6-2 CHECK AUTO These modes allow you to set a 9-band graphic equalizer for each of the 7 channels. These menus are for confirming the results of AUTO SETUP function equalizer measurement (AUDYSSEY, FRONT, FLAT). 1. Select “6. ACOUSTIC EQ” from MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. 2. 3. 1. Select “6. ACOUSTIC EQ” from MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. Select “PRESET G.
ADJUSTING THE MAIN VOLUME SELECTING THE SURROUND MODE Example: AUTO SURROUND (PLAY BACK) 7.1CH IN A/D HT-EQ 0 +10 MEMO SPKR A/B MUTE MULTI/ CAT M-SPKR VOLUME CL SOURCE SET OFF ON l/ AV SURROUND RECEIVER SR6001 EAK ATT ANALOG GHT EQ DIGITAL SLEEP SELECTING AN INPUT SOURCE DISPLAY P.DIRECT SURROUND AAC CH/ CAT DIGITAL C R LFE PCM SL S DOWN DISP SLEEP Before you can listen to any input media, you must first select the input source on the SR6001.
ENGLISH VIDEO CONVERT ANALOG VIDEO CONVERSION CONNECTION EXAMPLE • When a monitor is connected to the HDMI MONITOR OUT terminal of the SR6001 • When a monitor is connected to the COMPONENT VIDEO MONITOR OUT terminal of the SR6001 TEMPORARILY TURNING OFF THE SOUND AV SURROUND RECEIVER SR6001 INPUT SELECTOR CL DSD DOWN The SR6001 is equipped to convert video signals for monitor output.
SURROUND The SR6001 is equipped with many surround modes. These are provided to reproduce a variety of surround sound effects, according to the content of the source to be played. The available surround modes may be restricted depending on the input signal and speaker setup. SOURCE DIRECT In the Source Direct mode, the tone control circuit Acoustic EQ. and bass management configuration are bypassed for full-range frequency response and the purist audio reproduction.
ENGLISH Neo:6 Cinema, Neo:6 Music This mode decodes 2 channel signals into 6 channel signals using high-accuracy digital matrix technology. The DTS Neo:6 decoder has near-discrete properties in the frequency characteristics of the channels as well as in channel separation. According to the signals to be played back, DTS Neo:6 uses either the Neo:6 Cinema mode optimized for movie playback or the Neo:6 Music mode optimized for music playback.
Surround Mode Input Signal Decoding AUTO Dolby Surr.EX Dolby D (5.1ch) Dolby D (2ch) Dolby D (2ch Surr) DTS-ES DTS 96/24 DTS (5.1ch) Multi Ch-PCM Multi Ch-PCM 96kHz DSD (5.1ch) DSD (2ch) PCM (Audio) PCM 96kHz HDCD Analog 7.1ch input Dolby Surr.EX Dolby D (5.1ch) Dolby D (2ch) Dolby D (2ch Surr) DTS-ES DTS 96/24 DTS (5.1ch) Multi Ch-PCM Multi Ch-PCM 96kHz DSD (5.1ch) DSD (2ch) PCM (Audio) PCM 96kHz HDCD Analog 7.1ch input Dolby Surr.EX Dolby D (5.1ch) DTS-ES DTS (5.1ch) Multi-PCM DSD (5.1ch) Dolby Surr.
ENGLISH Surround Mode Input Signal Decoding Dolby Virtual Speaker Dolby Surr.EX Dolby D (5.1ch) Dolby D (2ch) Dolby D (2ch Surr) DTS-ES DTS 96/24 DTS (5.1ch) Multi Ch-PCM DSD (5.1ch) DSD (2ch) PCM (Audio) HDCD Analog Dolby Surr.EX Dolby D (5.1ch) Dolby D (2ch) Dolby D (2ch Surr) DTS-ES DTS 96/24 DTS (5.1ch) Multi Ch-PCM Multi Ch-PCM 96kHz DSD (5.1ch) DSD (2ch) PCM (Audio) HDCD Analog Dolby Surr.EX Dolby D (5.1ch) Dolby D (2ch) Dolby D (2ch Surr) DTS-ES DTS 96/24 DTS (5.1ch) Multi Ch-PCM DSD (5.
ATTENUATION TO ANALOG INPUT SIGNAL REC TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the SR6001. AUTO POWER ON 1. 2. 3. Be sure the TV auto mode is ENABLED. (Refer to page 38: PREFERENCE) Connect your TV TUNER (etc) to the TVVIDEO in terminal. Be sure to connect the VIDEO input. Turn OFF the power to the TV TUNER and the SR6001. 4. Turn ON the TV TUNER and tune in a receivable station. 5.
ENGLISH DISPLAY MODE SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT AV SURROUND RECEIVER SR6001 LEARN PURE DIRECT DISP SLEEP MULTI AUTO AUTO SURR TUNED DIRECT ST SPKR A B DISC 6.1 V-OFF MT X 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL TUNER SURROUND C SL S SOURCE SR SET OFF MD TAPE DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT AUX1 AUX2 AMP MULTI AUTO MULTI SPEAKER BAND 7.
The SR6001 is equipped for future expansion through the use of Multi channel Super Audio CD multichannel player or DVD-Audio player. When this is selected, the input signals connected to the L(front left), R (front right), CENTER, SL (surround left), SR (surround right) and SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH.
ENGLISH BASIC OPERATION (TUNER) To operate the unit from the remote control, press the TUNER button on the remote control so that the tuner mode is engaged. LISTENING TO THE TUNER (Using the SR6001) (Using the SR6001) 1. Turn the INPUT SELECTOR knob to select “TUNER”. 1. 2. Press the BAND button to select either FM or AM. 2. Press the BAND button to select either FM or AM. 3. Press the 3 or 4 cursor buttons on the front Panel for more than 1 second to start the auto tuning function. 3.
With this unit you can preset up to 60 FM/AM stations in any order. For each station, you can memorize the frequency and reception mode if desired. 3. 2. 4. SLEEP DISPLAY P.DIRECT SURROUND dts LIP SYNC/ INPUT AUTO 1 SLEEP MULTI AUTO AUTO SURR TUNED DIRECT ST SPKR A B DISC 6.1 V-OFF MTX 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL SL OUND DE C R LFE PCM S CS 3.
ENGLISH CLEARING STORED PRESET STATIONS 2. 3. SPKR A B V-OFF MTX 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL C 2. S dts ST SPKR A B DISC 6.1 V-OFF MTX 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL SURROUND DIGITAL C R LFE PCM SL S SR LIP SYNC/ INPUT 2 3 BAND EX/ES VIRTUAL T.MODE DOWN SURROUND 5 6 STEREO NIGHT 7 8 9 7.1CH IN A/D HT-EQ 0 +10 MEMO SPKR A/B MUTE UP MODE AUTO PURE DIRECT HT-EQ MULTI SPEAKER BAND T-MODE MEMORY 4.
Now in use in many countries, RDS (Radio Data System) is a description of the station’s programming hidden space in the FM signal. Your new receiver is equipped with RDS to assist in the selection of FM stations using station and network names, rather than broadcast frequencies. Additional RDS functions include the ability to search for programme types. PROGRAMME TYPE (PTY) DISPLAY PTY AUTO SEARCH The RDS system categorizes programmes according to their genre into different programme type (PTY) groups.
ENGLISH MULTI ROOM SYSTEM 2. The Multiroom System mode allows the same source or different sources to be heard in two rooms other than where this receiver is installed. 1. 4. 3. VOLUME DISP SLEEP MULTI AUTO AUTO SURR TUNED ST DIRECT SPKR A B DISC 6.1 V-OFF MT X 6.1 PEAK ATT ANALOG NIGHT EQ DIGITAL SURROUND DIGITAL L AAC R C LFE PCM SL DSD S SR DOWN SURROUND UP MULTI MODE AUTO PURE DIRECT HT-EQ SPEAKER MULTI BAND 7.
General: Controlling volume level, sleep timer, and muting. SeIecting input audio and video source. Multi Room output can be operated from a room where the receiver is not installed. This requires a separately sold IR receiver. (For connections, see page 23.) Tuner: Selecting band, controlling preset channel up and down, tuning up and down direct frequency call. 0 CH/ CAT +10 BASS VOLUME SPKR A/B MUTE MULTI/ CAT M-SPKR INFO MENU 2. 1.
ENGLISH TROUBLESHOOTING In case of trouble, check the following before calling for service: 1. 2. 3. Are the connections made properly ? Are you operating the unit properly following the user’s guide ? Are the power amplifiers and speaker working properly ? If the unit does not operate properly, check items shown in the following table.
SYMPTOM CAUSE The display does not appear over an HDMI connection. The connected monitor or projector does not support HDCP. REMEDY The HDMI input of on the TV is not on. Set HDMI input so that it turns on, as explained in the TV's instruction manual. The HDMI output on the source component (DVD, Set Top Box, etc.) is not on. Set HDMI output so that it turns on, as explained in the source component's instruction manual. The HDMI mode is not correctly set on the SR6001.
disconnect the plug from the AC line supply - after waiting at least three minutes, reconnect the plug to the AC line supply - re-attempt to operate the equipment Memory backup • In case a power outage occurs or the power cord is accidentally unplugged, the SR6001 is equipped with a backup function to prevent memory data such as the preset memory from being erased. HOW TO RESET THE UNIT AUTO SURR TUNED DIRECT ST SPKR A B DISC 6.1 V-OFF MTX 6.
SETUP CODES TV Acer .......................................................... 1141 Admiral .................................1002, 1009, 1089 Aiko .......................................................... 1059 Aiwa................................................1117, 1118 Akai .......................................................... 1001 Amtron ...................................................... 1023 Anam ........................................................ 1113 Anam National......................
Dimensia ..............................3004, 3063, 3085 Dixon ..............................................3077, 3081 Dynatech .................................................. 3035 Electrohome ............................................. 3052 Electrophonic ........................................... 3052 Emerson .................... 3009, 3015, 3016, 3017 3018, 3019, 3022, 3035 3047, 3052, 3054, 3073 Fisher .............................................3029, 3032 Fuji.....................................
Hughes ...........................................4001, 4016 Janeil ........................................................ 4025 JVC........................................................... 4017 Mitsubishi ................................................. 4001 Panasonic.......................................4004, 4010 Philips .............................................4031, 4035 Proscan ..................... 4002, 4008, 4009, 4011 Radio Shack ...................................4036, 4037 RCA ..........
www.marantz.com You can find your nearest authorized distributor or dealer on our website. is a registered trademark. Printed in China SR6001N DFU_8_Setup.indd iv 12/2006 00M25CW851310 mzh-d 06.12.
