User guide

66
(1*/,6+ '(876&+ )5$1d$,6 ,7$/,$12 (63$f2/ 1('(5/$1'6 69(16.$(1*/,6+ '(876&+ )5$1d$,6 ,7$/,$12 (63$f2/ 1('(5/$1'6 69(16.$
Operating learn mode
This remote control unit is capable of learning and storing codes used
by other remote controls that you already own.
For codes which are not learned, the remote control unit will transmit
either the Marantz preset codes from the initial settings, or remote
codes from another manufacturer’s AV equipment which is set by the
customer.
The receiver sensor for the remote control unit signals is located at the
top of the remote control unit.
This remote control unit is capable of learning around 160 codes.
NOTE
The learning procedure does not operate correctly if the batteries have
become worn.
n Learning procedure
1
3ODFHWKH0DUDQW]UHPRWHFRQWURODQGUHPRWH
FRQWUROIURPWKHRWKHUGHYLFHDSSUR[LPDWHO\FP
DSDUWZLWKWKHUHPRWHFRQWUROVLJQDOWUDQVPLVVLRQ
VHFWLRQVIDFLQJHDFKRWKHU
2
3UHVVDQGKROGGRZQSETDQG
SOURCE SEL XQWLOWKH/($51
LQGLFDWRUEOLQNV
3
3UHVVLQSXWVRXUFHVHOHFW
EXWWRQVWRVHOHFWWKHLQSXW
VRXUFH
4
6HOHFWWKHEXWWRQWREHOHDUQHG
LEARN indicator lights up.
NOTE
• The learning function is unavailable for all SOURCE and D.MODE in
any mode.
• The learning function is unavailable for all buttons in TUNER mode
and AMP mode.
5
3UHVV DQG KROG WKH EXWWRQ RI WKH RULJLQDO UHPRWH
FRQWUROXQLWWREHOHDUQHGXQWLOWKH6(1'LQGLFDWRU
EOLQNVWZLFH
NOTE
• If the SEND indicator blinks once, repeat this step.
• If the LEARN indicator flashes when the SEND indicator is lit, then
the button cannot be learned.
• When the memory of the remote control unit is full, the LEARN and
SEND indicators blink once. If you want to learn the code, you need
to erase a different learned button.
6
5HSHDWVWHSVDQG  WR OHDUQ RWKHU EXWWRQV IRU WKH
VDPHLQSXWVRXUFH
7
5HSHDWVWHSVWRWROHDUQRWKHULQSXWVRXUFHV
8
:KHQSURJUDPPLQJRIWKHUHPRWHFRQWUROXQLWLV
FRPSOHWHGSUHVV
SET
The LEARN display disappears, and the remote control unit
exits learn mode.
NOTE
• When the SEND indicator blinks once again, the transmitting code
is unavailable for remote control unit, or the transmitting signal has
been interrupted by noise.
• If no buttons are pressed for approximately 1 minutes while in the
LEARN mode, the remote control unit automatically exits from the
LEARN mode.
n Erasing programmed codes
Codes can be erased in three ways: by buttons, sources, and by all
memory contents.
Erasing the code by buttons
1
3UHVVDQGKROGGRZQSETDQG
SOURCE SELXQWLOWKH/($51
LQGLFDWRUEOLQNV
2
3UHVVLQSXWVRXUFHVHOHFWEXWWRQV
WRVHOHFWWKHLQSXWVRXUFH\RX
ZDQWWRGHOHWH
3
3UHVVDQGKROGGRZQD.MODE
DQGSUHVVWKHOHDUQHGEXWWRQWR
EHHUDVHGWZLFH
SEND indicator blinks twice and the
mode returns to LEARN mode.
4
7RUHWXUQWKHQRUPDOPRGHSUHVVSET
Erasing the code by SOURCE
1
3UHVVDQGKROGGRZQSETDQG
SOURCE SELXQWLOWKH/($51
LQGLFDWRUEOLQNV
2
3UHVVDQGKROGGRZQD.MODE
DQGSUHVVWKHOHDUQHGLQSXW
VRXUFHVHOHFWEXWWRQVWREHHUDVHG
WZLFH
LEARN indicator lights.
3
3UHVVENTERWRFRQWLQXHHUDVLQJ
• The SEND indicator blinks twice and
the mode returns to LEARN mode.
• To cancel the erasing operation, do not
press
ENTER, and simply press any
other button.
4
7RUHWXUQWKHQRUPDOPRGH
SUHVV
SET
5 cm